generic: backport at803x fixes

As patches for the AR8031/AR8033 copper page selection were merged
upstream, we can backport these patches.

This also fixes a PHY capabilities detection issue on the Ubiquiti
ER-X-SFP.

Signed-off-by: David Bauer <mail@david-bauer.net>

2 files changed, 0 insertions, 87 deletions

diff --git a/target/linux/generic/pending-5.10/735-net-phy-at803x-fix-at8033-sgmii-mode.patch b/target/linux/generic/pending-5.10/735-net-phy-at803x-fix-at8033-sgmii-mode.patch
deleted file mode 100644
index b063b10251..0000000000
--- a/target/linux/generic/pending-5.10/735-net-phy-at803x-fix-at8033-sgmii-mode.patch
+++ /dev/null
@@ -1,51 +0,0 @@
-From: Roman Yeryomin <roman@advem.lv>
-Subject: kernel: add at803x fix for sgmii mode
-
-Some (possibly broken) bootloaders incorreclty initialize at8033
-phy. This patch enables sgmii autonegotiation mode.
-
-[john@phrozen.org: felix added this to his upstream queue]
-
-Signed-off-by: Roman Yeryomin <roman@advem.lv>
----
- drivers/net/phy/at803x.c | 25 +++++++++++++++++++++++++
- 1 file changed, 25 insertions(+)
-
---- a/drivers/net/phy/at803x.c
-+++ b/drivers/net/phy/at803x.c
-@@ -76,6 +76,7 @@
- #define AT803X_LOC_MAC_ADDR_32_47_OFFSET	0x804A
- #define AT803X_REG_CHIP_CONFIG			0x1f
- #define AT803X_BT_BX_REG_SEL			0x8000
-+#define AT803X_SGMII_ANEG_EN			0x1000
- 
- #define AT803X_DEBUG_ADDR			0x1D
- #define AT803X_DEBUG_DATA			0x1E
-@@ -562,6 +563,27 @@ static int at8031_pll_config(struct phy_
- static int at803x_config_init(struct phy_device *phydev)
- {
- 	int ret;
-+	u32 v;
-+
-+	if (phydev->drv->phy_id == ATH8031_PHY_ID &&
-+		phydev->interface == PHY_INTERFACE_MODE_SGMII)
-+	{
-+		v = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
-+		/* select SGMII/fiber page */
-+		ret = phy_write(phydev, AT803X_REG_CHIP_CONFIG,
-+						v & ~AT803X_BT_BX_REG_SEL);
-+		if (ret)
-+			return ret;
-+		/* enable SGMII autonegotiation */
-+		ret = phy_write(phydev, MII_BMCR, AT803X_SGMII_ANEG_EN);
-+		if (ret)
-+			return ret;
-+		/* select copper page */
-+		ret = phy_write(phydev, AT803X_REG_CHIP_CONFIG,
-+						v | AT803X_BT_BX_REG_SEL);
-+		if (ret)
-+			return ret;
-+	}
- 
- 	/* The RX and TX delay default is:
- 	 *   after HW reset: RX delay enabled and TX delay disabled
diff --git a/target/linux/generic/pending-5.10/736-net-phy-at803x-add-at8031-features.patch b/target/linux/generic/pending-5.10/736-net-phy-at803x-add-at8031-features.patch
deleted file mode 100644
index 77d3946aae..0000000000
--- a/target/linux/generic/pending-5.10/736-net-phy-at803x-add-at8031-features.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-Add back explicit PHY feature flags for the AR8031 and
-AR8033 PHY instead of reading them from the PHY.
-
-The Botloader for Ubiquiti UniFi AC boards (and possibly more)
-leave fiber page selected, thus we will end up reading the PHY
-capabilities of the SGMII side (which does not offer 10 Mbit/s).
-
-We already have a hack in place, which switches back to the copper
-page, however this happens after capabilities are read.
-
-The original conversation about 735-net-phy-at803x-fix-at8033-sgmii-mode
-back in 2015 explicitly mention the UniFi AC Lite. The issue however is
-not missing autonegotiation on the Fiber side, but the fact the PHY
-is never switched to the copper side. So half of this patch is superfluous.
-
-A fix is currently being upstreamed. Once this is mainlined and available to us,
-these patches can be dropped:
-
-735-net-phy-at803x-fix-at8033-sgmii-mode.patch
-736-net-phy-at803x-add-at8031-features.patch
-
-This was tested on a UniFi AC Lite.
-
-See https://patchwork.kernel.org/project/netdevbpf/list/?series=467341
-
---- a/drivers/net/phy/at803x.c
-+++ b/drivers/net/phy/at803x.c
-@@ -1119,7 +1119,7 @@ static struct phy_driver at803x_driver[]
- 	.get_wol		= at803x_get_wol,
- 	.suspend		= at803x_suspend,
- 	.resume			= at803x_resume,
--	/* PHY_GBIT_FEATURES */
-+	.features               = PHY_GBIT_FEATURES,
- 	.read_status		= at803x_read_status,
- 	.aneg_done		= at803x_aneg_done,
- 	.ack_interrupt		= &at803x_ack_interrupt,