ar71xx: Add support for Netgear WNR2000v1

This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.

The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.

Short specification:

- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button

Factory/Initial flash instructions:

- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
  ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
  the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
  script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.

Commands to type in u-boot:

	# tells u-boot that we have a tftp server on 192.168.1.10
	setenv serverip 192.168.1.10

	# tells u-boot that the router should take the address 192.168.1.1
	setenv ipaddr 192.168.1.1

	# erase the region from 0x050000-0x3f0000
	erase 0xbf050000 +0x3A0000

	# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
	tftpboot 0x81000000 sqfs.bin
	# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
	# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
	cp.b 0x81000000 0xbf050000 0xZZZZZZ

	# same to the uImage.bin, write it right next to sqfs.bin
	# again, 0xYYYYYY is the length that tftpboot reports
	tftpboot 0x81000000 uImage.bin
	cp.b 0x81000000 0xbf2a0000 0xYYYYYY

	# We need to tell the kernel what board it is booting into, and where to find the partitions
	setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"

	# Tell u-boot where to find the uImage
	setenv bootcmd "bootm 0xbf2a0000"

	# Tell u-boot to save parameters to the u-boot-env partitions
	saveenv

	# Reset the board
	reset

Tested on:

- WNR2000v1 board.
- Initial flash works.

Known bugs:

- I don't know why factory image doesn't work on initial flash on stock
  firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
  installation (requiring a reinstall of sqfs and uImage).

Signed-off-by: Huan Truong <htruong@tnhh.net>

1 files changed, 2 insertions, 0 deletions

diff --git a/target/linux/generic/files/drivers/mtd/mtdsplit/mtdsplit_uimage.c b/target/linux/generic/files/drivers/mtd/mtdsplit/mtdsplit_uimage.c
index 26cb66ac7f..41a1b3746d 100644
--- a/target/linux/generic/files/drivers/mtd/mtdsplit/mtdsplit_uimage.c
+++ b/target/linux/generic/files/drivers/mtd/mtdsplit/mtdsplit_uimage.c
@@ -246,6 +246,7 @@ static struct mtd_part_parser uimage_generic_parser = {
 	.type = MTD_PARSER_TYPE_FIRMWARE,
 };
 
+#define FW_MAGIC_WNR2000V1	0x32303031
 #define FW_MAGIC_WNR2000V3	0x32303033
 #define FW_MAGIC_WNR2000V4	0x32303034
 #define FW_MAGIC_WNR2200	0x32323030
@@ -265,6 +266,7 @@ static ssize_t uimage_verify_wndr3700(u_char *buf, size_t len)
 	case FW_MAGIC_WNR612V2:
 	case FW_MAGIC_WNR1000V2:
 	case FW_MAGIC_WNR1000V2_VC:
+	case FW_MAGIC_WNR2000V1:
 	case FW_MAGIC_WNR2000V3:
 	case FW_MAGIC_WNR2200:
 	case FW_MAGIC_WNDR3700: