brcm63xx: remove kernel 4.9 support

This target got bumped to 4.14 a long time ago
in commit: 2308b87204206d84b6bf3dbc3d72591611cc6b78

Remove all leftover 4.9 files.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

1 files changed, 0 insertions, 92 deletions

diff --git a/target/linux/brcm63xx/patches-4.9/511-board_V2500V.patch b/target/linux/brcm63xx/patches-4.9/511-board_V2500V.patch
deleted file mode 100644
index 2d8bcceff2..0000000000
--- a/target/linux/brcm63xx/patches-4.9/511-board_V2500V.patch
+++ /dev/null
@@ -1,92 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -435,6 +435,26 @@ static struct board_info __initdata boar
- 	.has_pccard			= 1,
- 	.has_ehci0			= 1,
- };
-+
-+static struct board_info __initdata board_V2500V_BB = {
-+	.name				= "V2500V_BB",
-+        .expected_cpu_id                = 0x6348,
-+
-+        .has_enet0                      = 1,
-+        .has_enet1                      = 1,
-+        .has_pci                        = 1,
-+
-+        .enet0 = {
-+                .has_phy                = 1,
-+                .use_internal_phy       = 1,
-+        },
-+        .enet1 = {
-+		.has_phy		= 1,
-+		.phy_id			= 0,
-+                .force_speed_100        = 1,
-+                .force_duplex_full      = 1,
-+	},
-+};
- #endif /* CONFIG_BCM63XX_CPU_6348 */
- 
- /*
-@@ -707,6 +727,7 @@ static const struct board_info __initcon
- 	&board_96348_D4PW,
- 	&board_spw500v,
- 	&board_96348sv,
-+	&board_V2500V_BB,
- #endif
- 
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -746,6 +767,7 @@ static struct of_device_id const bcm963x
- 	{ .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, },
- 	{ .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, },
- 	{ .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, },
-+	{ .compatible = "bt,v2500v-bb", .data = &board_V2500V_BB, },
- 	{ .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, },
- 	{ .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, },
- 	{ .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, },
-@@ -805,6 +827,22 @@ void __init board_bcm963xx_init(void)
- 		val &= MPI_CSBASE_BASE_MASK;
- 	}
- 	boot_addr = (u8 *)KSEG1ADDR(val);
-+	pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+	/* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+	/* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+	/* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+	/* Do an early check of CFE and then select bank 0 */
-+
-+	if (boot_addr == (u8 *)0xbf800000) {
-+		u8 *tmp_boot_addr = (u8*)0xbfc00000;
-+
-+		bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
-+		if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
-+			pr_info("V2500V: nvram bank 0\n");
-+			boot_addr = tmp_boot_addr;
-+		}
-+	}
- 
- 	/* dump cfe version */
- 	cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -21,6 +21,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/flash.h>
- 
-+#include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_regs.h>
-@@ -247,6 +248,13 @@ int __init bcm63xx_flash_register(void)
- 			val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- 			val &= MPI_CSBASE_BASE_MASK;
- 
-+			/* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+			/* Loading from CFE always uses Bank 0 */
-+			if (!strcmp(board_get_name(), "V2500V_BB")) {
-+				pr_info("V2500V: Start in Bank 0\n");
-+				val = val + 0x400000; // Select Bank 0 start address
-+			}
-+
- 			mtd_resources[0].start = val;
- 			mtd_resources[0].end = 0x1FFFFFFF;
- 		}