brcm2708: rename all patches from raspberrypi git tree to use 950 prefix

Right now all brcm2708 patches are extracted from the non-mainline
raspberrypi/linux git tree. Many of them are hacks and/or are unneeded
in LEDE. Raspberry Pi is getting better and better mainline support so
it would be nice to finally start maintaining patches in a cleaner way:
1) Backport patches accepted in upstream tree
2) Start using upstream drivers
3) Pick only these patches that are needed for more complete support

Handling above tasks requires grouping patches - ideally using the same
prefixes as generic ones. It means we should rename existing patches to
use some high prefix. This will allow e.g. use 0xx for backported code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>

1 files changed, 1743 insertions, 0 deletions

diff --git a/target/linux/brcm2708/patches-4.9/950-0034-MMC-added-alternative-MMC-driver.patch b/target/linux/brcm2708/patches-4.9/950-0034-MMC-added-alternative-MMC-driver.patch
new file mode 100644
index 0000000000..70fb8f3d8c
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.9/950-0034-MMC-added-alternative-MMC-driver.patch
@@ -0,0 +1,1743 @@
+From 1620619c5fa6acae1e119d6461b5c9a2a9416e69 Mon Sep 17 00:00:00 2001
+From: gellert <gellert@raspberrypi.org>
+Date: Fri, 15 Aug 2014 16:35:06 +0100
+Subject: [PATCH] MMC: added alternative MMC driver
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+mmc: Disable CMD23 transfers on all cards
+
+Pending wire-level investigation of these types of transfers
+and associated errors on bcm2835-mmc, disable for now. Fallback of
+CMD18/CMD25 transfers will be used automatically by the MMC layer.
+
+Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
+
+mmc: bcm2835-mmc: enable DT support for all architectures
+
+Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
+Enable Device Tree support for all architectures.
+
+Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
+
+mmc: bcm2835-mmc: fix probe error handling
+
+Probe error handling is broken in several places.
+Simplify error handling by using device managed functions.
+Replace pr_{err,info} with dev_{err,info}.
+
+Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
+
+bcm2835-mmc: Add locks when accessing sdhost registers
+
+bcm2835-mmc: Add range of debug options for slowing things down
+
+bcm2835-mmc: Add option to disable some delays
+
+bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
+
+bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
+
+bcm2835-mmc: Adding overclocking option
+
+Allow a different clock speed to be substitued for a requested 50MHz.
+This option is exposed using the "overclock_50" DT parameter.
+Note that the mmc interface is restricted to EVEN integer divisions of
+250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
+next being 125 (250/2) which is much too high.
+
+Use at your own risk.
+
+bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
+
+Also only warn once for each overclock setting.
+
+mmc: bcm2835-mmc: Make available on ARCH_BCM2835
+
+Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
+
+Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
+
+BCM270x_DT: add bcm2835-mmc entry
+
+Add Device Tree entry for bcm2835-mmc.
+In non-DT mode, don't add the device in the board file.
+
+Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
+
+bcm2835-mmc: Don't overwrite MMC capabilities from DT
+
+bcm2835-mmc: Don't override bus width capabilities from devicetree
+
+Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
+so that the result read from devicetree via mmc_of_parse() is
+preserved.
+
+bcm2835-mmc: Only claim one DMA channel
+
+With both MMC controllers enabled there are few DMA channels left. The
+bcm2835-mmc driver only uses DMA in one direction at a time, so it
+doesn't need to claim two channels.
+
+See: https://github.com/raspberrypi/linux/issues/1327
+
+Signed-off-by: Phil Elwell <phil@raspberrypi.org>
+---
+ drivers/mmc/core/quirks.c      |   10 +
+ drivers/mmc/host/Kconfig       |   29 +
+ drivers/mmc/host/Makefile      |    1 +
+ drivers/mmc/host/bcm2835-mmc.c | 1574 ++++++++++++++++++++++++++++++++++++++++
+ 4 files changed, 1614 insertions(+)
+ create mode 100644 drivers/mmc/host/bcm2835-mmc.c
+
+--- a/drivers/mmc/core/quirks.c
++++ b/drivers/mmc/core/quirks.c
+@@ -53,6 +53,9 @@ static const struct mmc_fixup mmc_fixup_
+ 
+ void mmc_fixup_device(struct mmc_card *card, const struct mmc_fixup *table)
+ {
++#ifdef CONFIG_MMC_BCM2835
++	extern unsigned mmc_debug;
++#endif
+ 	const struct mmc_fixup *f;
+ 	u64 rev = cid_rev_card(card);
+ 
+@@ -79,5 +82,12 @@ void mmc_fixup_device(struct mmc_card *c
+ 			f->vendor_fixup(card, f->data);
+ 		}
+ 	}
++	/* SDHCI on BCM2708 - bug causes a certain sequence of CMD23 operations to fail.
++	 * Disable this flag for all cards (fall-back to CMD25/CMD18 multi-block transfers).
++	 */
++#ifdef CONFIG_MMC_BCM2835
++	if (mmc_debug & (1<<13))
++	card->quirks |= MMC_QUIRK_BLK_NO_CMD23;
++#endif
+ }
+ EXPORT_SYMBOL(mmc_fixup_device);
+--- a/drivers/mmc/host/Kconfig
++++ b/drivers/mmc/host/Kconfig
+@@ -4,6 +4,35 @@
+ 
+ comment "MMC/SD/SDIO Host Controller Drivers"
+ 
++config MMC_BCM2835
++	tristate "MMC support on BCM2835"
++	depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
++	help
++	  This selects the MMC Interface on BCM2835.
++
++	  If you have a controller with this interface, say Y or M here.
++
++	  If unsure, say N.
++
++config MMC_BCM2835_DMA
++	bool "DMA support on BCM2835 Arasan controller"
++	depends on MMC_BCM2835
++	help
++	  Enable DMA support on the Arasan SDHCI controller in Broadcom 2708
++	  based chips.
++
++	  If unsure, say N.
++
++config MMC_BCM2835_PIO_DMA_BARRIER
++	int "Block count limit for PIO transfers"
++	depends on MMC_BCM2835 && MMC_BCM2835_DMA
++	range 0 256
++	default 2
++	help
++	  The inclusive limit in bytes under which PIO will be used instead of DMA
++
++	  If unsure, say 2 here.
++
+ config MMC_ARMMMCI
+ 	tristate "ARM AMBA Multimedia Card Interface support"
+ 	depends on ARM_AMBA
+--- a/drivers/mmc/host/Makefile
++++ b/drivers/mmc/host/Makefile
+@@ -18,6 +18,7 @@ obj-$(CONFIG_MMC_SDHCI_S3C)	+= sdhci-s3c
+ obj-$(CONFIG_MMC_SDHCI_SIRF)   	+= sdhci-sirf.o
+ obj-$(CONFIG_MMC_SDHCI_F_SDH30)	+= sdhci_f_sdh30.o
+ obj-$(CONFIG_MMC_SDHCI_SPEAR)	+= sdhci-spear.o
++obj-$(CONFIG_MMC_BCM2835)	+= bcm2835-mmc.o
+ obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
+ obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
+ obj-$(CONFIG_MMC_MTK)		+= mtk-sd.o
+--- /dev/null
++++ b/drivers/mmc/host/bcm2835-mmc.c
+@@ -0,0 +1,1574 @@
++/*
++ * BCM2835 MMC host driver.
++ *
++ * Author:      Gellert Weisz <gellert@raspberrypi.org>
++ *              Copyright 2014
++ *
++ * Based on
++ *  sdhci-bcm2708.c by Broadcom
++ *  sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko
++ *  sdhci.c and sdhci-pci.c by Pierre Ossman
++ *
++ * This program is free software; you can redistribute it and/or modify it
++ * under the terms and conditions of the GNU General Public License,
++ * version 2, as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope it will be useful, but WITHOUT
++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
++ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
++ * more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
++ */
++
++#include <linux/delay.h>
++#include <linux/module.h>
++#include <linux/io.h>
++#include <linux/mmc/mmc.h>
++#include <linux/mmc/host.h>
++#include <linux/mmc/sd.h>
++#include <linux/scatterlist.h>
++#include <linux/of_address.h>
++#include <linux/of_irq.h>
++#include <linux/clk.h>
++#include <linux/platform_device.h>
++#include <linux/err.h>
++#include <linux/blkdev.h>
++#include <linux/dmaengine.h>
++#include <linux/dma-mapping.h>
++#include <linux/of_dma.h>
++
++#include "sdhci.h"
++
++
++#define DRIVER_NAME "mmc-bcm2835"
++
++#define DBG(f, x...) \
++pr_debug(DRIVER_NAME " [%s()]: " f, __func__, ## x)
++
++#ifndef CONFIG_MMC_BCM2835_DMA
++ #define FORCE_PIO
++#endif
++
++
++/* the inclusive limit in bytes under which PIO will be used instead of DMA */
++#ifdef CONFIG_MMC_BCM2835_PIO_DMA_BARRIER
++#define PIO_DMA_BARRIER CONFIG_MMC_BCM2835_PIO_DMA_BARRIER
++#else
++#define PIO_DMA_BARRIER 00
++#endif
++
++#define MIN_FREQ 400000
++#define TIMEOUT_VAL 0xE
++#define BCM2835_SDHCI_WRITE_DELAY(f)	(((2 * 1000000) / f) + 1)
++
++
++unsigned mmc_debug;
++unsigned mmc_debug2;
++
++struct bcm2835_host {
++	spinlock_t				lock;
++
++	void __iomem			*ioaddr;
++	u32						bus_addr;
++
++	struct mmc_host			*mmc;
++
++	u32						timeout;
++
++	int						clock;	/* Current clock speed */
++	u8						pwr;	/* Current voltage */
++
++	unsigned int			max_clk;		/* Max possible freq */
++	unsigned int			timeout_clk;	/* Timeout freq (KHz) */
++	unsigned int			clk_mul;		/* Clock Muliplier value */
++
++	struct tasklet_struct	finish_tasklet;		/* Tasklet structures */
++
++	struct timer_list		timer;			/* Timer for timeouts */
++
++	struct sg_mapping_iter	sg_miter;		/* SG state for PIO */
++	unsigned int			blocks;			/* remaining PIO blocks */
++
++	int						irq;			/* Device IRQ */
++
++
++	u32						ier;			/* cached registers */
++
++	struct mmc_request		*mrq;			/* Current request */
++	struct mmc_command		*cmd;			/* Current command */
++	struct mmc_data			*data;			/* Current data request */
++	unsigned int			data_early:1;		/* Data finished before cmd */
++
++	wait_queue_head_t		buf_ready_int;		/* Waitqueue for Buffer Read Ready interrupt */
++
++	u32						thread_isr;
++
++	u32						shadow;
++
++	/*DMA part*/
++	struct dma_chan			*dma_chan_rxtx;		/* DMA channel for reads and writes */
++	struct dma_slave_config		dma_cfg_rx;
++	struct dma_slave_config		dma_cfg_tx;
++	struct dma_async_tx_descriptor	*tx_desc;	/* descriptor */
++
++	bool					have_dma;
++	bool					use_dma;
++	/*end of DMA part*/
++
++	int						max_delay;	/* maximum length of time spent waiting */
++
++	int						flags;				/* Host attributes */
++#define SDHCI_REQ_USE_DMA	(1<<2)	/* Use DMA for this req. */
++#define SDHCI_DEVICE_DEAD	(1<<3)	/* Device unresponsive */
++#define SDHCI_AUTO_CMD12	(1<<6)	/* Auto CMD12 support */
++#define SDHCI_AUTO_CMD23	(1<<7)	/* Auto CMD23 support */
++#define SDHCI_SDIO_IRQ_ENABLED	(1<<9)	/* SDIO irq enabled */
++
++	u32				overclock_50;	/* frequency to use when 50MHz is requested (in MHz) */
++	u32				max_overclock;	/* Highest reported */
++};
++
++
++static inline void bcm2835_mmc_writel(struct bcm2835_host *host, u32 val, int reg, int from)
++{
++	unsigned delay;
++	lockdep_assert_held_once(&host->lock);
++	writel(val, host->ioaddr + reg);
++	udelay(BCM2835_SDHCI_WRITE_DELAY(max(host->clock, MIN_FREQ)));
++
++	delay = ((mmc_debug >> 16) & 0xf) << ((mmc_debug >> 20) & 0xf);
++	if (delay && !((1<<from) & mmc_debug2))
++		udelay(delay);
++}
++
++static inline void mmc_raw_writel(struct bcm2835_host *host, u32 val, int reg)
++{
++	unsigned delay;
++	lockdep_assert_held_once(&host->lock);
++	writel(val, host->ioaddr + reg);
++
++	delay = ((mmc_debug >> 24) & 0xf) << ((mmc_debug >> 28) & 0xf);
++	if (delay)
++		udelay(delay);
++}
++
++static inline u32 bcm2835_mmc_readl(struct bcm2835_host *host, int reg)
++{
++	lockdep_assert_held_once(&host->lock);
++	return readl(host->ioaddr + reg);
++}
++
++static inline void bcm2835_mmc_writew(struct bcm2835_host *host, u16 val, int reg)
++{
++	u32 oldval = (reg == SDHCI_COMMAND) ? host->shadow :
++		bcm2835_mmc_readl(host, reg & ~3);
++	u32 word_num = (reg >> 1) & 1;
++	u32 word_shift = word_num * 16;
++	u32 mask = 0xffff << word_shift;
++	u32 newval = (oldval & ~mask) | (val << word_shift);
++
++	if (reg == SDHCI_TRANSFER_MODE)
++		host->shadow = newval;
++	else
++		bcm2835_mmc_writel(host, newval, reg & ~3, 0);
++
++}
++
++static inline void bcm2835_mmc_writeb(struct bcm2835_host *host, u8 val, int reg)
++{
++	u32 oldval = bcm2835_mmc_readl(host, reg & ~3);
++	u32 byte_num = reg & 3;
++	u32 byte_shift = byte_num * 8;
++	u32 mask = 0xff << byte_shift;
++	u32 newval = (oldval & ~mask) | (val << byte_shift);
++
++	bcm2835_mmc_writel(host, newval, reg & ~3, 1);
++}
++
++
++static inline u16 bcm2835_mmc_readw(struct bcm2835_host *host, int reg)
++{
++	u32 val = bcm2835_mmc_readl(host, (reg & ~3));
++	u32 word_num = (reg >> 1) & 1;
++	u32 word_shift = word_num * 16;
++	u32 word = (val >> word_shift) & 0xffff;
++
++	return word;
++}
++
++static inline u8 bcm2835_mmc_readb(struct bcm2835_host *host, int reg)
++{
++	u32 val = bcm2835_mmc_readl(host, (reg & ~3));
++	u32 byte_num = reg & 3;
++	u32 byte_shift = byte_num * 8;
++	u32 byte = (val >> byte_shift) & 0xff;
++
++	return byte;
++}
++
++static void bcm2835_mmc_unsignal_irqs(struct bcm2835_host *host, u32 clear)
++{
++	u32 ier;
++
++	ier = bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE);
++	ier &= ~clear;
++	/* change which requests generate IRQs - makes no difference to
++	   the content of SDHCI_INT_STATUS, or the need to acknowledge IRQs */
++	bcm2835_mmc_writel(host, ier, SDHCI_SIGNAL_ENABLE, 2);
++}
++
++
++static void bcm2835_mmc_dumpregs(struct bcm2835_host *host)
++{
++	pr_debug(DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n",
++		mmc_hostname(host->mmc));
++
++	pr_debug(DRIVER_NAME ": Sys addr: 0x%08x | Version:  0x%08x\n",
++		bcm2835_mmc_readl(host, SDHCI_DMA_ADDRESS),
++		bcm2835_mmc_readw(host, SDHCI_HOST_VERSION));
++	pr_debug(DRIVER_NAME ": Blk size: 0x%08x | Blk cnt:  0x%08x\n",
++		bcm2835_mmc_readw(host, SDHCI_BLOCK_SIZE),
++		bcm2835_mmc_readw(host, SDHCI_BLOCK_COUNT));
++	pr_debug(DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n",
++		bcm2835_mmc_readl(host, SDHCI_ARGUMENT),
++		bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE));
++	pr_debug(DRIVER_NAME ": Present:  0x%08x | Host ctl: 0x%08x\n",
++		bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE),
++		bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL));
++	pr_debug(DRIVER_NAME ": Power:    0x%08x | Blk gap:  0x%08x\n",
++		bcm2835_mmc_readb(host, SDHCI_POWER_CONTROL),
++		bcm2835_mmc_readb(host, SDHCI_BLOCK_GAP_CONTROL));
++	pr_debug(DRIVER_NAME ": Wake-up:  0x%08x | Clock:    0x%08x\n",
++		bcm2835_mmc_readb(host, SDHCI_WAKE_UP_CONTROL),
++		bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL));
++	pr_debug(DRIVER_NAME ": Timeout:  0x%08x | Int stat: 0x%08x\n",
++		bcm2835_mmc_readb(host, SDHCI_TIMEOUT_CONTROL),
++		bcm2835_mmc_readl(host, SDHCI_INT_STATUS));
++	pr_debug(DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n",
++		bcm2835_mmc_readl(host, SDHCI_INT_ENABLE),
++		bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE));
++	pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
++		bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
++		bcm2835_mmc_readw(host, SDHCI_SLOT_INT_STATUS));
++	pr_debug(DRIVER_NAME ": Caps:     0x%08x | Caps_1:   0x%08x\n",
++		bcm2835_mmc_readl(host, SDHCI_CAPABILITIES),
++		bcm2835_mmc_readl(host, SDHCI_CAPABILITIES_1));
++	pr_debug(DRIVER_NAME ": Cmd:      0x%08x | Max curr: 0x%08x\n",
++		bcm2835_mmc_readw(host, SDHCI_COMMAND),
++		bcm2835_mmc_readl(host, SDHCI_MAX_CURRENT));
++	pr_debug(DRIVER_NAME ": Host ctl2: 0x%08x\n",
++		bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2));
++
++	pr_debug(DRIVER_NAME ": ===========================================\n");
++}
++
++
++static void bcm2835_mmc_reset(struct bcm2835_host *host, u8 mask)
++{
++	unsigned long timeout;
++	unsigned long flags;
++
++	spin_lock_irqsave(&host->lock, flags);
++	bcm2835_mmc_writeb(host, mask, SDHCI_SOFTWARE_RESET);
++
++	if (mask & SDHCI_RESET_ALL)
++		host->clock = 0;
++
++	/* Wait max 100 ms */
++	timeout = 100;
++
++	/* hw clears the bit when it's done */
++	while (bcm2835_mmc_readb(host, SDHCI_SOFTWARE_RESET) & mask) {
++		if (timeout == 0) {
++			pr_err("%s: Reset 0x%x never completed.\n",
++				mmc_hostname(host->mmc), (int)mask);
++			bcm2835_mmc_dumpregs(host);
++			return;
++		}
++		timeout--;
++		spin_unlock_irqrestore(&host->lock, flags);
++		mdelay(1);
++		spin_lock_irqsave(&host->lock, flags);
++	}
++
++	if (100-timeout > 10 && 100-timeout > host->max_delay) {
++		host->max_delay = 100-timeout;
++		pr_warning("Warning: MMC controller hung for %d ms\n", host->max_delay);
++	}
++	spin_unlock_irqrestore(&host->lock, flags);
++}
++
++static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
++
++static void bcm2835_mmc_init(struct bcm2835_host *host, int soft)
++{
++	unsigned long flags;
++	if (soft)
++		bcm2835_mmc_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
++	else
++		bcm2835_mmc_reset(host, SDHCI_RESET_ALL);
++
++	host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
++		    SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT |
++		    SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC |
++		    SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END |
++		    SDHCI_INT_RESPONSE;
++
++	spin_lock_irqsave(&host->lock, flags);
++	bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 3);
++	bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 3);
++	spin_unlock_irqrestore(&host->lock, flags);
++
++	if (soft) {
++		/* force clock reconfiguration */
++		host->clock = 0;
++		bcm2835_mmc_set_ios(host->mmc, &host->mmc->ios);
++	}
++}
++
++
++
++static void bcm2835_mmc_finish_data(struct bcm2835_host *host);
++
++static void bcm2835_mmc_dma_complete(void *param)
++{
++	struct bcm2835_host *host = param;
++	struct dma_chan *dma_chan;
++	unsigned long flags;
++	u32 dir_data;
++
++	spin_lock_irqsave(&host->lock, flags);
++
++	if (host->data && !(host->data->flags & MMC_DATA_WRITE)) {
++		/* otherwise handled in SDHCI IRQ */
++		dma_chan = host->dma_chan_rxtx;
++		dir_data = DMA_FROM_DEVICE;
++
++		dma_unmap_sg(dma_chan->device->dev,
++		     host->data->sg, host->data->sg_len,
++		     dir_data);
++
++		bcm2835_mmc_finish_data(host);
++	}
++
++	spin_unlock_irqrestore(&host->lock, flags);
++}
++
++static void bcm2835_bcm2835_mmc_read_block_pio(struct bcm2835_host *host)
++{
++	unsigned long flags;
++	size_t blksize, len, chunk;
++
++	u32 uninitialized_var(scratch);
++	u8 *buf;
++
++	blksize = host->data->blksz;
++	chunk = 0;
++
++	local_irq_save(flags);
++
++	while (blksize) {
++		if (!sg_miter_next(&host->sg_miter))
++			BUG();
++
++		len = min(host->sg_miter.length, blksize);
++
++		blksize -= len;
++		host->sg_miter.consumed = len;
++
++		buf = host->sg_miter.addr;
++
++		while (len) {
++			if (chunk == 0) {
++				scratch = bcm2835_mmc_readl(host, SDHCI_BUFFER);
++				chunk = 4;
++			}
++
++			*buf = scratch & 0xFF;
++
++			buf++;
++			scratch >>= 8;
++			chunk--;
++			len--;
++		}
++	}
++
++	sg_miter_stop(&host->sg_miter);
++
++	local_irq_restore(flags);
++}
++
++static void bcm2835_bcm2835_mmc_write_block_pio(struct bcm2835_host *host)
++{
++	unsigned long flags;
++	size_t blksize, len, chunk;
++	u32 scratch;
++	u8 *buf;
++
++	blksize = host->data->blksz;
++	chunk = 0;
++	chunk = 0;
++	scratch = 0;
++
++	local_irq_save(flags);
++
++	while (blksize) {
++		if (!sg_miter_next(&host->sg_miter))
++			BUG();
++
++		len = min(host->sg_miter.length, blksize);
++
++		blksize -= len;
++		host->sg_miter.consumed = len;
++
++		buf = host->sg_miter.addr;
++
++		while (len) {
++			scratch |= (u32)*buf << (chunk * 8);
++
++			buf++;
++			chunk++;
++			len--;
++
++			if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
++				mmc_raw_writel(host, scratch, SDHCI_BUFFER);
++				chunk = 0;
++				scratch = 0;
++			}
++		}
++	}
++
++	sg_miter_stop(&host->sg_miter);
++
++	local_irq_restore(flags);
++}
++
++
++static void bcm2835_mmc_transfer_pio(struct bcm2835_host *host)
++{
++	u32 mask;
++
++	BUG_ON(!host->data);
++
++	if (host->blocks == 0)
++		return;
++
++	if (host->data->flags & MMC_DATA_READ)
++		mask = SDHCI_DATA_AVAILABLE;
++	else
++		mask = SDHCI_SPACE_AVAILABLE;
++
++	while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) {
++
++		if (host->data->flags & MMC_DATA_READ)
++			bcm2835_bcm2835_mmc_read_block_pio(host);
++		else
++			bcm2835_bcm2835_mmc_write_block_pio(host);
++
++		host->blocks--;
++
++		/* QUIRK used in sdhci.c removes the 'if' */
++		/* but it seems this is unnecessary */
++		if (host->blocks == 0)
++			break;
++
++
++	}
++}
++
++
++static void bcm2835_mmc_transfer_dma(struct bcm2835_host *host)
++{
++	u32 len, dir_data, dir_slave;
++	struct dma_async_tx_descriptor *desc = NULL;
++	struct dma_chan *dma_chan;
++
++
++	WARN_ON(!host->data);
++
++	if (!host->data)
++		return;
++
++	if (host->blocks == 0)
++		return;
++
++	dma_chan = host->dma_chan_rxtx;
++	if (host->data->flags & MMC_DATA_READ) {
++		dir_data = DMA_FROM_DEVICE;
++		dir_slave = DMA_DEV_TO_MEM;
++	} else {
++		dir_data = DMA_TO_DEVICE;
++		dir_slave = DMA_MEM_TO_DEV;
++	}
++
++	/* The parameters have already been validated, so this will not fail */
++	(void)dmaengine_slave_config(dma_chan,
++				     (dir_data == DMA_FROM_DEVICE) ?
++				     &host->dma_cfg_rx :
++				     &host->dma_cfg_tx);
++
++	BUG_ON(!dma_chan->device);
++	BUG_ON(!dma_chan->device->dev);
++	BUG_ON(!host->data->sg);
++
++	len = dma_map_sg(dma_chan->device->dev, host->data->sg,
++			 host->data->sg_len, dir_data);
++	if (len > 0) {
++		desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg,
++					       len, dir_slave,
++					       DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
++	} else {
++		dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n");
++	}
++	if (desc) {
++		unsigned long flags;
++		spin_lock_irqsave(&host->lock, flags);
++		bcm2835_mmc_unsignal_irqs(host, SDHCI_INT_DATA_AVAIL |
++						    SDHCI_INT_SPACE_AVAIL);
++		host->tx_desc = desc;
++		desc->callback = bcm2835_mmc_dma_complete;
++		desc->callback_param = host;
++		spin_unlock_irqrestore(&host->lock, flags);
++		dmaengine_submit(desc);
++		dma_async_issue_pending(dma_chan);
++	}
++
++}
++
++
++
++static void bcm2835_mmc_set_transfer_irqs(struct bcm2835_host *host)
++{
++	u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
++	u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
++
++	if (host->use_dma)
++		host->ier = (host->ier & ~pio_irqs) | dma_irqs;
++	else
++		host->ier = (host->ier & ~dma_irqs) | pio_irqs;
++
++	bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 4);
++	bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 4);
++}
++
++
++static void bcm2835_mmc_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd)
++{
++	u8 count;
++	struct mmc_data *data = cmd->data;
++
++	WARN_ON(host->data);
++
++	if (data || (cmd->flags & MMC_RSP_BUSY)) {
++		count = TIMEOUT_VAL;
++		bcm2835_mmc_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
++	}
++
++	if (!data)
++		return;
++
++	/* Sanity checks */
++	BUG_ON(data->blksz * data->blocks > 524288);
++	BUG_ON(data->blksz > host->mmc->max_blk_size);
++	BUG_ON(data->blocks > 65535);
++
++	host->data = data;
++	host->data_early = 0;
++	host->data->bytes_xfered = 0;
++
++
++	if (!(host->flags & SDHCI_REQ_USE_DMA)) {
++		int flags;
++
++		flags = SG_MITER_ATOMIC;
++		if (host->data->flags & MMC_DATA_READ)
++			flags |= SG_MITER_TO_SG;
++		else
++			flags |= SG_MITER_FROM_SG;
++		sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
++		host->blocks = data->blocks;
++	}
++
++	host->use_dma = host->have_dma && data->blocks > PIO_DMA_BARRIER;
++
++	bcm2835_mmc_set_transfer_irqs(host);
++
++	/* Set the DMA boundary value and block size */
++	bcm2835_mmc_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
++		data->blksz), SDHCI_BLOCK_SIZE);
++	bcm2835_mmc_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
++
++	BUG_ON(!host->data);
++}
++
++static void bcm2835_mmc_set_transfer_mode(struct bcm2835_host *host,
++	struct mmc_command *cmd)
++{
++	u16 mode;
++	struct mmc_data *data = cmd->data;
++
++	if (data == NULL) {
++		/* clear Auto CMD settings for no data CMDs */
++		mode = bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE);
++		bcm2835_mmc_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
++				SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
++		return;
++	}
++
++	WARN_ON(!host->data);
++
++	mode = SDHCI_TRNS_BLK_CNT_EN;
++
++	if ((mmc_op_multi(cmd->opcode) || data->blocks > 1)) {
++		mode |= SDHCI_TRNS_MULTI;
++
++		/*
++		 * If we are sending CMD23, CMD12 never gets sent
++		 * on successful completion (so no Auto-CMD12).
++		 */
++		if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12))
++			mode |= SDHCI_TRNS_AUTO_CMD12;
++		else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
++			mode |= SDHCI_TRNS_AUTO_CMD23;
++			bcm2835_mmc_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2, 5);
++		}
++	}
++
++	if (data->flags & MMC_DATA_READ)
++		mode |= SDHCI_TRNS_READ;
++	if (host->flags & SDHCI_REQ_USE_DMA)
++		mode |= SDHCI_TRNS_DMA;
++
++	bcm2835_mmc_writew(host, mode, SDHCI_TRANSFER_MODE);
++}
++
++void bcm2835_mmc_send_command(struct bcm2835_host *host, struct mmc_command *cmd)
++{
++	int flags;
++	u32 mask;
++	unsigned long timeout;
++
++	WARN_ON(host->cmd);
++
++	/* Wait max 10 ms */
++	timeout = 1000;
++
++	mask = SDHCI_CMD_INHIBIT;
++	if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY))
++		mask |= SDHCI_DATA_INHIBIT;
++
++	/* We shouldn't wait for data inihibit for stop commands, even
++	   though they might use busy signaling */
++	if (host->mrq->data && (cmd == host->mrq->data->stop))
++		mask &= ~SDHCI_DATA_INHIBIT;
++
++	while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) {
++		if (timeout == 0) {
++			pr_err("%s: Controller never released inhibit bit(s).\n",
++				mmc_hostname(host->mmc));
++			bcm2835_mmc_dumpregs(host);
++			cmd->error = -EIO;
++			tasklet_schedule(&host->finish_tasklet);
++			return;
++		}
++		timeout--;
++		udelay(10);
++	}
++
++	if ((1000-timeout)/100 > 1 && (1000-timeout)/100 > host->max_delay) {
++		host->max_delay = (1000-timeout)/100;
++		pr_warning("Warning: MMC controller hung for %d ms\n", host->max_delay);
++	}
++
++	timeout = jiffies;
++	if (!cmd->data && cmd->busy_timeout > 9000)
++		timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
++	else
++		timeout += 10 * HZ;
++	mod_timer(&host->timer, timeout);
++
++	host->cmd = cmd;
++
++	bcm2835_mmc_prepare_data(host, cmd);
++
++	bcm2835_mmc_writel(host, cmd->arg, SDHCI_ARGUMENT, 6);
++
++	bcm2835_mmc_set_transfer_mode(host, cmd);
++
++	if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
++		pr_err("%s: Unsupported response type!\n",
++			mmc_hostname(host->mmc));
++		cmd->error = -EINVAL;
++		tasklet_schedule(&host->finish_tasklet);
++		return;
++	}
++
++	if (!(cmd->flags & MMC_RSP_PRESENT))
++		flags = SDHCI_CMD_RESP_NONE;
++	else if (cmd->flags & MMC_RSP_136)
++		flags = SDHCI_CMD_RESP_LONG;
++	else if (cmd->flags & MMC_RSP_BUSY)
++		flags = SDHCI_CMD_RESP_SHORT_BUSY;
++	else
++		flags = SDHCI_CMD_RESP_SHORT;
++
++	if (cmd->flags & MMC_RSP_CRC)
++		flags |= SDHCI_CMD_CRC;
++	if (cmd->flags & MMC_RSP_OPCODE)
++		flags |= SDHCI_CMD_INDEX;
++
++	if (cmd->data)
++		flags |= SDHCI_CMD_DATA;
++
++	bcm2835_mmc_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
++}
++
++
++static void bcm2835_mmc_finish_data(struct bcm2835_host *host)
++{
++	struct mmc_data *data;
++
++	BUG_ON(!host->data);
++
++	data = host->data;
++	host->data = NULL;
++
++	if (data->error)
++		data->bytes_xfered = 0;
++	else
++		data->bytes_xfered = data->blksz * data->blocks;
++
++	/*
++	 * Need to send CMD12 if -
++	 * a) open-ended multiblock transfer (no CMD23)
++	 * b) error in multiblock transfer
++	 */
++	if (data->stop &&
++	    (data->error ||
++	     !host->mrq->sbc)) {
++
++		/*
++		 * The controller needs a reset of internal state machines
++		 * upon error conditions.
++		 */
++		if (data->error) {
++			bcm2835_mmc_reset(host, SDHCI_RESET_CMD);
++			bcm2835_mmc_reset(host, SDHCI_RESET_DATA);
++		}
++
++		bcm2835_mmc_send_command(host, data->stop);
++	} else
++		tasklet_schedule(&host->finish_tasklet);
++}
++
++static void bcm2835_mmc_finish_command(struct bcm2835_host *host)
++{
++	int i;
++
++	BUG_ON(host->cmd == NULL);
++
++	if (host->cmd->flags & MMC_RSP_PRESENT) {
++		if (host->cmd->flags & MMC_RSP_136) {
++			/* CRC is stripped so we need to do some shifting. */
++			for (i = 0; i < 4; i++) {
++				host->cmd->resp[i] = bcm2835_mmc_readl(host,
++					SDHCI_RESPONSE + (3-i)*4) << 8;
++				if (i != 3)
++					host->cmd->resp[i] |=
++						bcm2835_mmc_readb(host,
++						SDHCI_RESPONSE + (3-i)*4-1);
++			}
++		} else {
++			host->cmd->resp[0] = bcm2835_mmc_readl(host, SDHCI_RESPONSE);
++		}
++	}
++
++	host->cmd->error = 0;
++
++	/* Finished CMD23, now send actual command. */
++	if (host->cmd == host->mrq->sbc) {
++		host->cmd = NULL;
++		bcm2835_mmc_send_command(host, host->mrq->cmd);
++
++		if (host->mrq->cmd->data && host->use_dma) {
++			/* DMA transfer starts now, PIO starts after interrupt */
++			bcm2835_mmc_transfer_dma(host);
++		}
++	} else {
++
++		/* Processed actual command. */
++		if (host->data && host->data_early)
++			bcm2835_mmc_finish_data(host);
++
++		if (!host->cmd->data)
++			tasklet_schedule(&host->finish_tasklet);
++
++		host->cmd = NULL;
++	}
++}
++
++
++static void bcm2835_mmc_timeout_timer(unsigned long data)
++{
++	struct bcm2835_host *host;
++	unsigned long flags;
++
++	host = (struct bcm2835_host *)data;
++
++	spin_lock_irqsave(&host->lock, flags);
++
++	if (host->mrq) {
++		pr_err("%s: Timeout waiting for hardware interrupt.\n",
++			mmc_hostname(host->mmc));
++		bcm2835_mmc_dumpregs(host);
++
++		if (host->data) {
++			host->data->error = -ETIMEDOUT;
++			bcm2835_mmc_finish_data(host);
++		} else {
++			if (host->cmd)
++				host->cmd->error = -ETIMEDOUT;
++			else
++				host->mrq->cmd->error = -ETIMEDOUT;
++
++			tasklet_schedule(&host->finish_tasklet);
++		}
++	}
++
++	mmiowb();
++	spin_unlock_irqrestore(&host->lock, flags);
++}
++
++
++static void bcm2835_mmc_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable)
++{
++	if (!(host->flags & SDHCI_DEVICE_DEAD)) {
++		if (enable)
++			host->ier |= SDHCI_INT_CARD_INT;
++		else
++			host->ier &= ~SDHCI_INT_CARD_INT;
++
++		bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 7);
++		bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 7);
++		mmiowb();
++	}
++}
++
++static void bcm2835_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
++{
++	struct bcm2835_host *host = mmc_priv(mmc);
++	unsigned long flags;
++
++	spin_lock_irqsave(&host->lock, flags);
++	if (enable)
++		host->flags |= SDHCI_SDIO_IRQ_ENABLED;
++	else
++		host->flags &= ~SDHCI_SDIO_IRQ_ENABLED;
++
++	bcm2835_mmc_enable_sdio_irq_nolock(host, enable);
++	spin_unlock_irqrestore(&host->lock, flags);
++}
++
++static void bcm2835_mmc_cmd_irq(struct bcm2835_host *host, u32 intmask)
++{
++
++	BUG_ON(intmask == 0);
++
++	if (!host->cmd) {
++		pr_err("%s: Got command interrupt 0x%08x even "
++			"though no command operation was in progress.\n",
++			mmc_hostname(host->mmc), (unsigned)intmask);
++		bcm2835_mmc_dumpregs(host);
++		return;
++	}
++
++	if (intmask & SDHCI_INT_TIMEOUT)
++		host->cmd->error = -ETIMEDOUT;
++	else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT |
++			SDHCI_INT_INDEX)) {
++			host->cmd->error = -EILSEQ;
++	}
++
++	if (host->cmd->error) {
++		tasklet_schedule(&host->finish_tasklet);
++		return;
++	}
++
++	if (intmask & SDHCI_INT_RESPONSE)
++		bcm2835_mmc_finish_command(host);
++
++}
++
++static void bcm2835_mmc_data_irq(struct bcm2835_host *host, u32 intmask)
++{
++	struct dma_chan *dma_chan;
++	u32 dir_data;
++
++	BUG_ON(intmask == 0);
++
++	if (!host->data) {
++		/*
++		 * The "data complete" interrupt is also used to
++		 * indicate that a busy state has ended. See comment
++		 * above in sdhci_cmd_irq().
++		 */
++		if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
++			if (intmask & SDHCI_INT_DATA_END) {
++				bcm2835_mmc_finish_command(host);
++				return;
++			}
++		}
++
++		pr_debug("%s: Got data interrupt 0x%08x even "
++			"though no data operation was in progress.\n",
++			mmc_hostname(host->mmc), (unsigned)intmask);
++		bcm2835_mmc_dumpregs(host);
++
++		return;
++	}
++
++	if (intmask & SDHCI_INT_DATA_TIMEOUT)
++		host->data->error = -ETIMEDOUT;
++	else if (intmask & SDHCI_INT_DATA_END_BIT)
++		host->data->error = -EILSEQ;
++	else if ((intmask & SDHCI_INT_DATA_CRC) &&
++		SDHCI_GET_CMD(bcm2835_mmc_readw(host, SDHCI_COMMAND))
++			!= MMC_BUS_TEST_R)
++		host->data->error = -EILSEQ;
++
++	if (host->use_dma) {
++		if  (host->data->flags & MMC_DATA_WRITE) {
++			/* IRQ handled here */
++
++			dma_chan = host->dma_chan_rxtx;
++			dir_data = DMA_TO_DEVICE;
++			dma_unmap_sg(dma_chan->device->dev,
++				 host->data->sg, host->data->sg_len,
++				 dir_data);
++
++			bcm2835_mmc_finish_data(host);
++		}
++
++	} else {
++		if (host->data->error)
++			bcm2835_mmc_finish_data(host);
++		else {
++			if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
++				bcm2835_mmc_transfer_pio(host);
++
++			if (intmask & SDHCI_INT_DATA_END) {
++				if (host->cmd) {
++					/*
++					 * Data managed to finish before the
++					 * command completed. Make sure we do
++					 * things in the proper order.
++					 */
++					host->data_early = 1;
++				} else {
++					bcm2835_mmc_finish_data(host);
++				}
++			}
++		}
++	}
++}
++
++
++static irqreturn_t bcm2835_mmc_irq(int irq, void *dev_id)
++{
++	irqreturn_t result = IRQ_NONE;
++	struct bcm2835_host *host = dev_id;
++	u32 intmask, mask, unexpected = 0;
++	int max_loops = 16;
++
++	spin_lock(&host->lock);
++
++	intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS);
++
++	if (!intmask || intmask == 0xffffffff) {
++		result = IRQ_NONE;
++		goto out;
++	}
++
++	do {
++		/* Clear selected interrupts. */
++		mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
++				  SDHCI_INT_BUS_POWER);
++		bcm2835_mmc_writel(host, mask, SDHCI_INT_STATUS, 8);
++
++
++		if (intmask & SDHCI_INT_CMD_MASK)
++			bcm2835_mmc_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK);
++
++		if (intmask & SDHCI_INT_DATA_MASK)
++			bcm2835_mmc_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
++
++		if (intmask & SDHCI_INT_BUS_POWER)
++			pr_err("%s: Card is consuming too much power!\n",
++				mmc_hostname(host->mmc));
++
++		if (intmask & SDHCI_INT_CARD_INT) {
++			bcm2835_mmc_enable_sdio_irq_nolock(host, false);
++			host->thread_isr |= SDHCI_INT_CARD_INT;
++			result = IRQ_WAKE_THREAD;
++		}
++
++		intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
++			     SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
++			     SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER |
++			     SDHCI_INT_CARD_INT);
++
++		if (intmask) {
++			unexpected |= intmask;
++			bcm2835_mmc_writel(host, intmask, SDHCI_INT_STATUS, 9);
++		}
++
++		if (result == IRQ_NONE)
++			result = IRQ_HANDLED;
++
++		intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS);
++	} while (intmask && --max_loops);
++out:
++	spin_unlock(&host->lock);
++
++	if (unexpected) {
++		pr_err("%s: Unexpected interrupt 0x%08x.\n",
++			   mmc_hostname(host->mmc), unexpected);
++		bcm2835_mmc_dumpregs(host);
++	}
++
++	return result;
++}
++
++static irqreturn_t bcm2835_mmc_thread_irq(int irq, void *dev_id)
++{
++	struct bcm2835_host *host = dev_id;
++	unsigned long flags;
++	u32 isr;
++
++	spin_lock_irqsave(&host->lock, flags);
++	isr = host->thread_isr;
++	host->thread_isr = 0;
++	spin_unlock_irqrestore(&host->lock, flags);
++
++	if (isr & SDHCI_INT_CARD_INT) {
++		sdio_run_irqs(host->mmc);
++
++		spin_lock_irqsave(&host->lock, flags);
++		if (host->flags & SDHCI_SDIO_IRQ_ENABLED)
++			bcm2835_mmc_enable_sdio_irq_nolock(host, true);
++		spin_unlock_irqrestore(&host->lock, flags);
++	}
++
++	return isr ? IRQ_HANDLED : IRQ_NONE;
++}
++
++
++
++void bcm2835_mmc_set_clock(struct bcm2835_host *host, unsigned int clock)
++{
++	int div = 0; /* Initialized for compiler warning */
++	int real_div = div, clk_mul = 1;
++	u16 clk = 0;
++	unsigned long timeout;
++	unsigned int input_clock = clock;
++
++	if (host->overclock_50 && (clock == 50000000))
++		clock = host->overclock_50 * 1000000 + 999999;
++
++	host->mmc->actual_clock = 0;
++
++	bcm2835_mmc_writew(host, 0, SDHCI_CLOCK_CONTROL);
++
++	if (clock == 0)
++		return;
++
++	/* Version 3.00 divisors must be a multiple of 2. */
++	if (host->max_clk <= clock)
++		div = 1;
++	else {
++		for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
++			 div += 2) {
++			if ((host->max_clk / div) <= clock)
++				break;
++		}
++	}
++
++	real_div = div;
++	div >>= 1;
++
++	if (real_div)
++		clock = (host->max_clk * clk_mul) / real_div;
++	host->mmc->actual_clock = clock;
++
++	if ((clock > input_clock) && (clock > host->max_overclock)) {
++		pr_warn("%s: Overclocking to %dHz\n",
++			mmc_hostname(host->mmc), clock);
++		host->max_overclock = clock;
++	}
++
++	clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
++	clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
++		<< SDHCI_DIVIDER_HI_SHIFT;
++	clk |= SDHCI_CLOCK_INT_EN;
++	bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL);
++
++	/* Wait max 20 ms */
++	timeout = 20;
++	while (!((clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL))
++		& SDHCI_CLOCK_INT_STABLE)) {
++		if (timeout == 0) {
++			pr_err("%s: Internal clock never "
++				"stabilised.\n", mmc_hostname(host->mmc));
++			bcm2835_mmc_dumpregs(host);
++			return;
++		}
++		timeout--;
++		mdelay(1);
++	}
++
++	if (20-timeout > 10 && 20-timeout > host->max_delay) {
++		host->max_delay = 20-timeout;
++		pr_warning("Warning: MMC controller hung for %d ms\n", host->max_delay);
++	}
++
++	clk |= SDHCI_CLOCK_CARD_EN;
++	bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL);
++}
++
++static void bcm2835_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
++{
++	struct bcm2835_host *host;
++	unsigned long flags;
++
++	host = mmc_priv(mmc);
++
++	spin_lock_irqsave(&host->lock, flags);
++
++	WARN_ON(host->mrq != NULL);
++
++	host->mrq = mrq;
++
++	if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
++		bcm2835_mmc_send_command(host, mrq->sbc);
++	else
++		bcm2835_mmc_send_command(host, mrq->cmd);
++
++	mmiowb();
++	spin_unlock_irqrestore(&host->lock, flags);
++
++	if (!(mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23)) && mrq->cmd->data && host->use_dma) {
++		/* DMA transfer starts now, PIO starts after interrupt */
++		bcm2835_mmc_transfer_dma(host);
++	}
++}
++
++
++static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
++{
++
++	struct bcm2835_host *host = mmc_priv(mmc);
++	unsigned long flags;
++	u8 ctrl;
++	u16 clk, ctrl_2;
++
++	pr_debug("bcm2835_mmc_set_ios: clock %d, pwr %d, bus_width %d, timing %d, vdd %d, drv_type %d\n",
++		 ios->clock, ios->power_mode, ios->bus_width,
++		 ios->timing, ios->signal_voltage, ios->drv_type);
++
++	spin_lock_irqsave(&host->lock, flags);
++
++	if (!ios->clock || ios->clock != host->clock) {
++		bcm2835_mmc_set_clock(host, ios->clock);
++		host->clock = ios->clock;
++	}
++
++	if (host->pwr != SDHCI_POWER_330) {
++		host->pwr = SDHCI_POWER_330;
++		bcm2835_mmc_writeb(host, SDHCI_POWER_330 | SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
++	}
++
++	ctrl = bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL);
++
++	/* set bus width */
++	ctrl &= ~SDHCI_CTRL_8BITBUS;
++	if (ios->bus_width == MMC_BUS_WIDTH_4)
++		ctrl |= SDHCI_CTRL_4BITBUS;
++	else
++		ctrl &= ~SDHCI_CTRL_4BITBUS;
++
++	ctrl &= ~SDHCI_CTRL_HISPD; /* NO_HISPD_BIT */
++
++
++	bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL);
++	/*
++	 * We only need to set Driver Strength if the
++	 * preset value enable is not set.
++	 */
++	ctrl_2 = bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2);
++	ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
++	if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
++		ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
++	else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
++		ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
++
++	bcm2835_mmc_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
++
++	/* Reset SD Clock Enable */
++	clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL);
++	clk &= ~SDHCI_CLOCK_CARD_EN;
++	bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL);
++
++	/* Re-enable SD Clock */
++	bcm2835_mmc_set_clock(host, host->clock);
++	bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL);
++
++	mmiowb();
++
++	spin_unlock_irqrestore(&host->lock, flags);
++}
++
++
++static struct mmc_host_ops bcm2835_ops = {
++	.request = bcm2835_mmc_request,
++	.set_ios = bcm2835_mmc_set_ios,
++	.enable_sdio_irq = bcm2835_mmc_enable_sdio_irq,
++};
++
++
++static void bcm2835_mmc_tasklet_finish(unsigned long param)
++{
++	struct bcm2835_host *host;
++	unsigned long flags;
++	struct mmc_request *mrq;
++
++	host = (struct bcm2835_host *)param;
++
++	spin_lock_irqsave(&host->lock, flags);
++
++	/*
++	 * If this tasklet gets rescheduled while running, it will
++	 * be run again afterwards but without any active request.
++	 */
++	if (!host->mrq) {
++		spin_unlock_irqrestore(&host->lock, flags);
++		return;
++	}
++
++	del_timer(&host->timer);
++
++	mrq = host->mrq;
++
++	/*
++	 * The controller needs a reset of internal state machines
++	 * upon error conditions.
++	 */
++	if (!(host->flags & SDHCI_DEVICE_DEAD) &&
++	    ((mrq->cmd && mrq->cmd->error) ||
++		 (mrq->data && (mrq->data->error ||
++		  (mrq->data->stop && mrq->data->stop->error))))) {
++
++		spin_unlock_irqrestore(&host->lock, flags);
++		bcm2835_mmc_reset(host, SDHCI_RESET_CMD);
++		bcm2835_mmc_reset(host, SDHCI_RESET_DATA);
++		spin_lock_irqsave(&host->lock, flags);
++	}
++
++	host->mrq = NULL;
++	host->cmd = NULL;
++	host->data = NULL;
++
++	mmiowb();
++
++	spin_unlock_irqrestore(&host->lock, flags);
++	mmc_request_done(host->mmc, mrq);
++}
++
++
++
++static int bcm2835_mmc_add_host(struct bcm2835_host *host)
++{
++	struct mmc_host *mmc = host->mmc;
++	struct device *dev = mmc->parent;
++#ifndef FORCE_PIO
++	struct dma_slave_config cfg;
++#endif
++	int ret;
++
++	bcm2835_mmc_reset(host, SDHCI_RESET_ALL);
++
++	host->clk_mul = 0;
++
++	mmc->f_max = host->max_clk;
++	mmc->f_max = host->max_clk;
++	mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
++
++	/* SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK */
++	host->timeout_clk = mmc->f_max / 1000;
++	mmc->max_busy_timeout = (1 << 27) / host->timeout_clk;
++
++	/* host controller capabilities */
++	mmc->caps |= MMC_CAP_CMD23 | MMC_CAP_ERASE | MMC_CAP_NEEDS_POLL |
++		MMC_CAP_SDIO_IRQ | MMC_CAP_SD_HIGHSPEED |
++		MMC_CAP_MMC_HIGHSPEED;
++
++	mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
++
++	host->flags = SDHCI_AUTO_CMD23;
++
++	dev_info(dev, "mmc_debug:%x mmc_debug2:%x\n", mmc_debug, mmc_debug2);
++#ifdef FORCE_PIO
++	dev_info(dev, "Forcing PIO mode\n");
++	host->have_dma = false;
++#else
++	if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) {
++		dev_err(dev, "%s: Unable to initialise DMA channel. Falling back to PIO\n",
++			DRIVER_NAME);
++		host->have_dma = false;
++	} else {
++		dev_info(dev, "DMA channel allocated");
++
++		cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
++		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
++		cfg.slave_id = 11;		/* DREQ channel */
++
++		/* Validate the slave configurations */
++
++		cfg.direction = DMA_MEM_TO_DEV;
++		cfg.src_addr = 0;
++		cfg.dst_addr = host->bus_addr + SDHCI_BUFFER;
++
++		ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg);
++
++		if (ret == 0) {
++			host->dma_cfg_tx = cfg;
++
++			cfg.direction = DMA_DEV_TO_MEM;
++			cfg.src_addr = host->bus_addr + SDHCI_BUFFER;
++			cfg.dst_addr = 0;
++
++			ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg);
++		}
++
++		if (ret == 0) {
++			host->dma_cfg_rx = cfg;
++
++			host->use_dma = true;
++		} else {
++			pr_err("%s: unable to configure DMA channel. "
++			       "Faling back to PIO\n",
++			       mmc_hostname(mmc));
++			dma_release_channel(host->dma_chan_rxtx);
++			host->dma_chan_rxtx = NULL;
++			host->use_dma = false;
++		}
++	}
++#endif
++	mmc->max_segs = 128;
++	mmc->max_req_size = 524288;
++	mmc->max_seg_size = mmc->max_req_size;
++	mmc->max_blk_size = 512;
++	mmc->max_blk_count =  65535;
++
++	/* report supported voltage ranges */
++	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
++
++	tasklet_init(&host->finish_tasklet,
++		bcm2835_mmc_tasklet_finish, (unsigned long)host);
++
++	setup_timer(&host->timer, bcm2835_mmc_timeout_timer, (unsigned long)host);
++	init_waitqueue_head(&host->buf_ready_int);
++
++	bcm2835_mmc_init(host, 0);
++	ret = devm_request_threaded_irq(dev, host->irq, bcm2835_mmc_irq,
++					bcm2835_mmc_thread_irq, IRQF_SHARED,
++					mmc_hostname(mmc), host);
++	if (ret) {
++		dev_err(dev, "Failed to request IRQ %d: %d\n", host->irq, ret);
++		goto untasklet;
++	}
++
++	mmiowb();
++	mmc_add_host(mmc);
++
++	return 0;
++
++untasklet:
++	tasklet_kill(&host->finish_tasklet);
++
++	return ret;
++}
++
++static int bcm2835_mmc_probe(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct device_node *node = dev->of_node;
++	struct clk *clk;
++	struct resource *iomem;
++	struct bcm2835_host *host;
++	struct mmc_host *mmc;
++	const __be32 *addr;
++	int ret;
++
++	mmc = mmc_alloc_host(sizeof(*host), dev);
++	if (!mmc)
++		return -ENOMEM;
++
++	mmc->ops = &bcm2835_ops;
++	host = mmc_priv(mmc);
++	host->mmc = mmc;
++	host->timeout = msecs_to_jiffies(1000);
++	spin_lock_init(&host->lock);
++
++	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	host->ioaddr = devm_ioremap_resource(dev, iomem);
++	if (IS_ERR(host->ioaddr)) {
++		ret = PTR_ERR(host->ioaddr);
++		goto err;
++	}
++
++	addr = of_get_address(node, 0, NULL, NULL);
++	if (!addr) {
++		dev_err(dev, "could not get DMA-register address\n");
++		return -ENODEV;
++	}
++	host->bus_addr = be32_to_cpup(addr);
++	pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n",
++		 (unsigned long)host->ioaddr,
++		 (unsigned long)iomem->start,
++		 (unsigned long)host->bus_addr);
++
++#ifndef FORCE_PIO
++	if (node) {
++		host->dma_chan_rxtx = dma_request_slave_channel(dev, "rx-tx");
++		if (!host->dma_chan_rxtx)
++			host->dma_chan_rxtx =
++				dma_request_slave_channel(dev, "tx");
++		if (!host->dma_chan_rxtx)
++			host->dma_chan_rxtx =
++				dma_request_slave_channel(dev, "rx");
++	} else {
++		dma_cap_mask_t mask;
++
++		dma_cap_zero(mask);
++		/* we don't care about the channel, any would work */
++		dma_cap_set(DMA_SLAVE, mask);
++		host->dma_chan_rxtx = dma_request_channel(mask, NULL, NULL);
++	}
++#endif
++	clk = devm_clk_get(dev, NULL);
++	if (IS_ERR(clk)) {
++		ret = PTR_ERR(clk);
++		if (ret == -EPROBE_DEFER)
++			dev_info(dev, "could not get clk, deferring probe\n");
++		else
++			dev_err(dev, "could not get clk\n");
++		goto err;
++	}
++
++	host->max_clk = clk_get_rate(clk);
++
++	host->irq = platform_get_irq(pdev, 0);
++	if (host->irq <= 0) {
++		dev_err(dev, "get IRQ failed\n");
++		ret = -EINVAL;
++		goto err;
++	}
++
++	if (node) {
++		mmc_of_parse(mmc);
++
++		/* Read any custom properties */
++		of_property_read_u32(node,
++				     "brcm,overclock-50",
++				     &host->overclock_50);
++	} else {
++		mmc->caps |= MMC_CAP_4_BIT_DATA;
++	}
++
++	ret = bcm2835_mmc_add_host(host);
++	if (ret)
++		goto err;
++
++	platform_set_drvdata(pdev, host);
++
++	return 0;
++err:
++	mmc_free_host(mmc);
++
++	return ret;
++}
++
++static int bcm2835_mmc_remove(struct platform_device *pdev)
++{
++	struct bcm2835_host *host = platform_get_drvdata(pdev);
++	unsigned long flags;
++	int dead;
++	u32 scratch;
++
++	dead = 0;
++	scratch = bcm2835_mmc_readl(host, SDHCI_INT_STATUS);
++	if (scratch == (u32)-1)
++		dead = 1;
++
++
++	if (dead) {
++		spin_lock_irqsave(&host->lock, flags);
++
++		host->flags |= SDHCI_DEVICE_DEAD;
++
++		if (host->mrq) {
++			pr_err("%s: Controller removed during "
++				" transfer!\n", mmc_hostname(host->mmc));
++
++			host->mrq->cmd->error = -ENOMEDIUM;
++			tasklet_schedule(&host->finish_tasklet);
++		}
++
++		spin_unlock_irqrestore(&host->lock, flags);
++	}
++
++	mmc_remove_host(host->mmc);
++
++	if (!dead)
++		bcm2835_mmc_reset(host, SDHCI_RESET_ALL);
++
++	free_irq(host->irq, host);
++
++	del_timer_sync(&host->timer);
++
++	tasklet_kill(&host->finish_tasklet);
++
++	mmc_free_host(host->mmc);
++	platform_set_drvdata(pdev, NULL);
++
++	return 0;
++}
++
++
++static const struct of_device_id bcm2835_mmc_match[] = {
++	{ .compatible = "brcm,bcm2835-mmc" },
++	{ }
++};
++MODULE_DEVICE_TABLE(of, bcm2835_mmc_match);
++
++
++
++static struct platform_driver bcm2835_mmc_driver = {
++	.probe      = bcm2835_mmc_probe,
++	.remove     = bcm2835_mmc_remove,
++	.driver     = {
++		.name		= DRIVER_NAME,
++		.owner		= THIS_MODULE,
++		.of_match_table	= bcm2835_mmc_match,
++	},
++};
++module_platform_driver(bcm2835_mmc_driver);
++
++module_param(mmc_debug, uint, 0644);
++module_param(mmc_debug2, uint, 0644);
++MODULE_ALIAS("platform:mmc-bcm2835");
++MODULE_DESCRIPTION("BCM2835 SDHCI driver");
++MODULE_LICENSE("GPL v2");
++MODULE_AUTHOR("Gellert Weisz");