brcm2708: update to latest version

As usual these patches were extracted from the raspberry pi repo:
https://github.com/raspberrypi/linux/commits/rpi-4.4.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

1 files changed, 0 insertions, 635 deletions

diff --git a/target/linux/brcm2708/patches-4.4/0046-Add-Chris-Boot-s-i2c-driver.patch b/target/linux/brcm2708/patches-4.4/0046-Add-Chris-Boot-s-i2c-driver.patch
deleted file mode 100644
index 6730ee6fd8..0000000000
--- a/target/linux/brcm2708/patches-4.4/0046-Add-Chris-Boot-s-i2c-driver.patch
+++ /dev/null
@@ -1,635 +0,0 @@
-From 72181304010d3aa74cd2b98db592554a541ce4c2 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix@gmail.com>
-Date: Wed, 17 Jun 2015 15:44:08 +0100
-Subject: [PATCH 046/170] Add Chris Boot's i2c driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-i2c-bcm2708: fixed baudrate
-
-Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
-In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
-This resulted in incorrect setting of CDIV and higher baudrate than intended.
-Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
-After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
-The correct baudrate is shown in the log after the cdiv > 0xffff correction.
-
-Perform I2C combined transactions when possible
-
-Perform I2C combined transactions whenever possible, within the
-restrictions of the Broadcomm Serial Controller.
-
-Disable DONE interrupt during TA poll
-
-Prevent interrupt from being triggered if poll is missed and transfer
-starts and finishes.
-
-i2c: Make combined transactions optional and disabled by default
-
-i2c: bcm2708: add device tree support
-
-Add DT support to driver and add to .dtsi file.
-Setup pins in .dts file.
-i2c is disabled by default.
-
-Signed-off-by: Noralf Tronnes <notro@tronnes.org>
-
-bcm2708: don't register i2c controllers when using DT
-
-The devices for the i2c controllers are in the Device Tree.
-Only register devices when not using DT.
-
-Signed-off-by: Noralf Tronnes <notro@tronnes.org>
-
-I2C: Only register the I2C device for the current board revision
-
-i2c_bcm2708: Fix clock reference counting
-
-Fix grabbing lock from atomic context in i2c driver
-
-2 main changes:
-- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
-      /* poll for transfer start bit (should only take 1-20 polls) */
-  This implies that the setup function can now fail so account for this everywhere it's called
-- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
-
-i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
-
-i2c-bcm2708: Increase timeouts to allow larger transfers
-
-Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
-for completion. The default timeout is 1 second.
-
-See: https://github.com/raspberrypi/linux/issues/260
-
-i2c-bcm2708/BCM270X_DT: Add support for I2C2
-
-The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
-use of this bus can break an attached display - use with caution.
-
-It is recommended to disable accesses by VideoCore by setting
-hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
-
-The interface is disabled by default - enable using the
-i2c2_iknowwhatimdoing DT parameter.
-
-bcm2708-spi: Don't use static pin configuration with DT
-
-Also remove superfluous error checking - the SPI framework ensures the
-validity of the chip_select value.
-
-i2c-bcm2708: Remove non-DT support
-
-Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
----
- drivers/i2c/busses/Kconfig       |  21 +-
- drivers/i2c/busses/Makefile      |   2 +
- drivers/i2c/busses/i2c-bcm2708.c | 493 +++++++++++++++++++++++++++++++++++++++
- 3 files changed, 515 insertions(+), 1 deletion(-)
- create mode 100644 drivers/i2c/busses/i2c-bcm2708.c
-
---- a/drivers/i2c/busses/Kconfig
-+++ b/drivers/i2c/busses/Kconfig
-@@ -8,6 +8,25 @@ menu "I2C Hardware Bus support"
- comment "PC SMBus host controller drivers"
- 	depends on PCI
- 
-+config I2C_BCM2708
-+	tristate "BCM2708 BSC"
-+	depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-+	help
-+	  Enabling this option will add BSC (Broadcom Serial Controller)
-+	  support for the BCM2708. BSC is a Broadcom proprietary bus compatible
-+	  with I2C/TWI/SMBus.
-+
-+config I2C_BCM2708_BAUDRATE
-+	prompt "BCM2708 I2C baudrate"
-+	depends on I2C_BCM2708
-+	int
-+	default 100000
-+	help
-+	  Set the I2C baudrate. This will alter the default value. A
-+	  different baudrate can be set by using a module parameter as well. If
-+	  no parameter is provided when loading, this is the value that will be
-+	  used.
-+
- config I2C_ALI1535
- 	tristate "ALI 1535"
- 	depends on PCI
-@@ -365,7 +384,7 @@ config I2C_AXXIA
- 
- config I2C_BCM2835
- 	tristate "Broadcom BCM2835 I2C controller"
--	depends on ARCH_BCM2835
-+	depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- 	help
- 	  If you say yes to this option, support will be included for the
- 	  BCM2835 I2C controller.
---- a/drivers/i2c/busses/Makefile
-+++ b/drivers/i2c/busses/Makefile
-@@ -2,6 +2,8 @@
- # Makefile for the i2c bus drivers.
- #
- 
-+obj-$(CONFIG_I2C_BCM2708)	+= i2c-bcm2708.o
-+
- # ACPI drivers
- obj-$(CONFIG_I2C_SCMI)		+= i2c-scmi.o
- 
---- /dev/null
-+++ b/drivers/i2c/busses/i2c-bcm2708.c
-@@ -0,0 +1,493 @@
-+/*
-+ * Driver for Broadcom BCM2708 BSC Controllers
-+ *
-+ * Copyright (C) 2012 Chris Boot & Frank Buss
-+ *
-+ * This driver is inspired by:
-+ * i2c-ocores.c, by Peter Korsgaard <jacmet@sunsite.dk>
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/spinlock.h>
-+#include <linux/clk.h>
-+#include <linux/err.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/io.h>
-+#include <linux/slab.h>
-+#include <linux/i2c.h>
-+#include <linux/interrupt.h>
-+#include <linux/sched.h>
-+#include <linux/wait.h>
-+
-+/* BSC register offsets */
-+#define BSC_C			0x00
-+#define BSC_S			0x04
-+#define BSC_DLEN		0x08
-+#define BSC_A			0x0c
-+#define BSC_FIFO		0x10
-+#define BSC_DIV			0x14
-+#define BSC_DEL			0x18
-+#define BSC_CLKT		0x1c
-+
-+/* Bitfields in BSC_C */
-+#define BSC_C_I2CEN		0x00008000
-+#define BSC_C_INTR		0x00000400
-+#define BSC_C_INTT		0x00000200
-+#define BSC_C_INTD		0x00000100
-+#define BSC_C_ST		0x00000080
-+#define BSC_C_CLEAR_1		0x00000020
-+#define BSC_C_CLEAR_2		0x00000010
-+#define BSC_C_READ		0x00000001
-+
-+/* Bitfields in BSC_S */
-+#define BSC_S_CLKT		0x00000200
-+#define BSC_S_ERR		0x00000100
-+#define BSC_S_RXF		0x00000080
-+#define BSC_S_TXE		0x00000040
-+#define BSC_S_RXD		0x00000020
-+#define BSC_S_TXD		0x00000010
-+#define BSC_S_RXR		0x00000008
-+#define BSC_S_TXW		0x00000004
-+#define BSC_S_DONE		0x00000002
-+#define BSC_S_TA		0x00000001
-+
-+#define I2C_WAIT_LOOP_COUNT	200
-+
-+#define DRV_NAME		"bcm2708_i2c"
-+
-+static unsigned int baudrate = CONFIG_I2C_BCM2708_BAUDRATE;
-+module_param(baudrate, uint, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
-+MODULE_PARM_DESC(baudrate, "The I2C baudrate");
-+
-+static bool combined = false;
-+module_param(combined, bool, 0644);
-+MODULE_PARM_DESC(combined, "Use combined transactions");
-+
-+struct bcm2708_i2c {
-+	struct i2c_adapter adapter;
-+
-+	spinlock_t lock;
-+	void __iomem *base;
-+	int irq;
-+	struct clk *clk;
-+	u32 cdiv;
-+
-+	struct completion done;
-+
-+	struct i2c_msg *msg;
-+	int pos;
-+	int nmsgs;
-+	bool error;
-+};
-+
-+static inline u32 bcm2708_rd(struct bcm2708_i2c *bi, unsigned reg)
-+{
-+	return readl(bi->base + reg);
-+}
-+
-+static inline void bcm2708_wr(struct bcm2708_i2c *bi, unsigned reg, u32 val)
-+{
-+	writel(val, bi->base + reg);
-+}
-+
-+static inline void bcm2708_bsc_reset(struct bcm2708_i2c *bi)
-+{
-+	bcm2708_wr(bi, BSC_C, 0);
-+	bcm2708_wr(bi, BSC_S, BSC_S_CLKT | BSC_S_ERR | BSC_S_DONE);
-+}
-+
-+static inline void bcm2708_bsc_fifo_drain(struct bcm2708_i2c *bi)
-+{
-+	while ((bcm2708_rd(bi, BSC_S) & BSC_S_RXD) && (bi->pos < bi->msg->len))
-+		bi->msg->buf[bi->pos++] = bcm2708_rd(bi, BSC_FIFO);
-+}
-+
-+static inline void bcm2708_bsc_fifo_fill(struct bcm2708_i2c *bi)
-+{
-+	while ((bcm2708_rd(bi, BSC_S) & BSC_S_TXD) && (bi->pos < bi->msg->len))
-+		bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]);
-+}
-+
-+static inline int bcm2708_bsc_setup(struct bcm2708_i2c *bi)
-+{
-+	u32 cdiv, s;
-+	u32 c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_ST | BSC_C_CLEAR_1;
-+	int wait_loops = I2C_WAIT_LOOP_COUNT;
-+
-+	/* Can't call clk_get_rate as it locks a mutex and here we are spinlocked.
-+	 * Use the value that we cached in the probe.
-+	 */
-+	cdiv = bi->cdiv;
-+
-+	if (bi->msg->flags & I2C_M_RD)
-+		c |= BSC_C_INTR | BSC_C_READ;
-+	else
-+		c |= BSC_C_INTT;
-+
-+	bcm2708_wr(bi, BSC_DIV, cdiv);
-+	bcm2708_wr(bi, BSC_A, bi->msg->addr);
-+	bcm2708_wr(bi, BSC_DLEN, bi->msg->len);
-+	if (combined)
-+	{
-+		/* Do the next two messages meet combined transaction criteria?
-+		   - Current message is a write, next message is a read
-+		   - Both messages to same slave address
-+		   - Write message can fit inside FIFO (16 bytes or less) */
-+		if ( (bi->nmsgs > 1) &&
-+			!(bi->msg[0].flags & I2C_M_RD) && (bi->msg[1].flags & I2C_M_RD) &&
-+			 (bi->msg[0].addr == bi->msg[1].addr) && (bi->msg[0].len <= 16)) {
-+			/* Fill FIFO with entire write message (16 byte FIFO) */
-+			while (bi->pos < bi->msg->len) {
-+				bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]);
-+			}
-+			/* Start write transfer (no interrupts, don't clear FIFO) */
-+			bcm2708_wr(bi, BSC_C, BSC_C_I2CEN | BSC_C_ST);
-+
-+			/* poll for transfer start bit (should only take 1-20 polls) */
-+			do {
-+				s = bcm2708_rd(bi, BSC_S);
-+			} while (!(s & (BSC_S_TA | BSC_S_ERR | BSC_S_CLKT | BSC_S_DONE)) && --wait_loops >= 0);
-+
-+			/* did we time out or some error occured? */
-+			if (wait_loops < 0 || (s & (BSC_S_ERR | BSC_S_CLKT))) {
-+				return -1;
-+			}
-+
-+			/* Send next read message before the write transfer finishes. */
-+			bi->nmsgs--;
-+			bi->msg++;
-+			bi->pos = 0;
-+			bcm2708_wr(bi, BSC_DLEN, bi->msg->len);
-+			c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_INTR | BSC_C_ST | BSC_C_READ;
-+		}
-+	}
-+	bcm2708_wr(bi, BSC_C, c);
-+
-+	return 0;
-+}
-+
-+static irqreturn_t bcm2708_i2c_interrupt(int irq, void *dev_id)
-+{
-+	struct bcm2708_i2c *bi = dev_id;
-+	bool handled = true;
-+	u32 s;
-+	int ret;
-+
-+	spin_lock(&bi->lock);
-+
-+	/* we may see camera interrupts on the "other" I2C channel
-+		   Just return if we've not sent anything */
-+	if (!bi->nmsgs || !bi->msg) {
-+		goto early_exit;
-+	}
-+
-+	s = bcm2708_rd(bi, BSC_S);
-+
-+	if (s & (BSC_S_CLKT | BSC_S_ERR)) {
-+		bcm2708_bsc_reset(bi);
-+		bi->error = true;
-+
-+		bi->msg = 0; /* to inform the that all work is done */
-+		bi->nmsgs = 0;
-+		/* wake up our bh */
-+		complete(&bi->done);
-+	} else if (s & BSC_S_DONE) {
-+		bi->nmsgs--;
-+
-+		if (bi->msg->flags & I2C_M_RD) {
-+			bcm2708_bsc_fifo_drain(bi);
-+		}
-+
-+		bcm2708_bsc_reset(bi);
-+
-+		if (bi->nmsgs) {
-+			/* advance to next message */
-+			bi->msg++;
-+			bi->pos = 0;
-+			ret = bcm2708_bsc_setup(bi);
-+			if (ret < 0) {
-+				bcm2708_bsc_reset(bi);
-+				bi->error = true;
-+				bi->msg = 0; /* to inform the that all work is done */
-+				bi->nmsgs = 0;
-+				/* wake up our bh */
-+				complete(&bi->done);
-+				goto early_exit;
-+			}
-+		} else {
-+			bi->msg = 0; /* to inform the that all work is done */
-+			bi->nmsgs = 0;
-+			/* wake up our bh */
-+			complete(&bi->done);
-+		}
-+	} else if (s & BSC_S_TXW) {
-+		bcm2708_bsc_fifo_fill(bi);
-+	} else if (s & BSC_S_RXR) {
-+		bcm2708_bsc_fifo_drain(bi);
-+	} else {
-+		handled = false;
-+	}
-+
-+early_exit:
-+	spin_unlock(&bi->lock);
-+
-+	return handled ? IRQ_HANDLED : IRQ_NONE;
-+}
-+
-+static int bcm2708_i2c_master_xfer(struct i2c_adapter *adap,
-+	struct i2c_msg *msgs, int num)
-+{
-+	struct bcm2708_i2c *bi = adap->algo_data;
-+	unsigned long flags;
-+	int ret;
-+
-+	spin_lock_irqsave(&bi->lock, flags);
-+
-+	reinit_completion(&bi->done);
-+	bi->msg = msgs;
-+	bi->pos = 0;
-+	bi->nmsgs = num;
-+	bi->error = false;
-+
-+	ret = bcm2708_bsc_setup(bi);
-+
-+	spin_unlock_irqrestore(&bi->lock, flags);
-+
-+	/* check the result of the setup */
-+	if (ret < 0)
-+	{
-+		dev_err(&adap->dev, "transfer setup timed out\n");
-+		goto error_timeout;
-+	}
-+
-+	ret = wait_for_completion_timeout(&bi->done, adap->timeout);
-+	if (ret == 0) {
-+		dev_err(&adap->dev, "transfer timed out\n");
-+		goto error_timeout;
-+	}
-+
-+	ret = bi->error ? -EIO : num;
-+	return ret;
-+
-+error_timeout:
-+	spin_lock_irqsave(&bi->lock, flags);
-+	bcm2708_bsc_reset(bi);
-+	bi->msg = 0; /* to inform the interrupt handler that there's nothing else to be done */
-+	bi->nmsgs = 0;
-+	spin_unlock_irqrestore(&bi->lock, flags);
-+	return -ETIMEDOUT;
-+}
-+
-+static u32 bcm2708_i2c_functionality(struct i2c_adapter *adap)
-+{
-+	return I2C_FUNC_I2C | /*I2C_FUNC_10BIT_ADDR |*/ I2C_FUNC_SMBUS_EMUL;
-+}
-+
-+static struct i2c_algorithm bcm2708_i2c_algorithm = {
-+	.master_xfer = bcm2708_i2c_master_xfer,
-+	.functionality = bcm2708_i2c_functionality,
-+};
-+
-+static int bcm2708_i2c_probe(struct platform_device *pdev)
-+{
-+	struct resource *regs;
-+	int irq, err = -ENOMEM;
-+	struct clk *clk;
-+	struct bcm2708_i2c *bi;
-+	struct i2c_adapter *adap;
-+	unsigned long bus_hz;
-+	u32 cdiv;
-+
-+	if (pdev->dev.of_node) {
-+		u32 bus_clk_rate;
-+		pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c");
-+		if (pdev->id < 0) {
-+			dev_err(&pdev->dev, "alias is missing\n");
-+			return -EINVAL;
-+		}
-+		if (!of_property_read_u32(pdev->dev.of_node,
-+					"clock-frequency", &bus_clk_rate))
-+			baudrate = bus_clk_rate;
-+		else
-+			dev_warn(&pdev->dev,
-+				"Could not read clock-frequency property\n");
-+	}
-+
-+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+	if (!regs) {
-+		dev_err(&pdev->dev, "could not get IO memory\n");
-+		return -ENXIO;
-+	}
-+
-+	irq = platform_get_irq(pdev, 0);
-+	if (irq < 0) {
-+		dev_err(&pdev->dev, "could not get IRQ\n");
-+		return irq;
-+	}
-+
-+	clk = clk_get(&pdev->dev, NULL);
-+	if (IS_ERR(clk)) {
-+		dev_err(&pdev->dev, "could not find clk: %ld\n", PTR_ERR(clk));
-+		return PTR_ERR(clk);
-+	}
-+
-+	err = clk_prepare_enable(clk);
-+	if (err) {
-+		dev_err(&pdev->dev, "could not enable clk: %d\n", err);
-+		goto out_clk_put;
-+	}
-+
-+	bi = kzalloc(sizeof(*bi), GFP_KERNEL);
-+	if (!bi)
-+		goto out_clk_disable;
-+
-+	platform_set_drvdata(pdev, bi);
-+
-+	adap = &bi->adapter;
-+	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DDC;
-+	adap->algo = &bcm2708_i2c_algorithm;
-+	adap->algo_data = bi;
-+	adap->dev.parent = &pdev->dev;
-+	adap->nr = pdev->id;
-+	strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name));
-+	adap->dev.of_node = pdev->dev.of_node;
-+
-+	switch (pdev->id) {
-+	case 0:
-+		adap->class = I2C_CLASS_HWMON;
-+		break;
-+	case 1:
-+		adap->class = I2C_CLASS_DDC;
-+		break;
-+	case 2:
-+		adap->class = I2C_CLASS_DDC;
-+		break;
-+	default:
-+		dev_err(&pdev->dev, "can only bind to BSC 0, 1 or 2\n");
-+		err = -ENXIO;
-+		goto out_free_bi;
-+	}
-+
-+	spin_lock_init(&bi->lock);
-+	init_completion(&bi->done);
-+
-+	bi->base = ioremap(regs->start, resource_size(regs));
-+	if (!bi->base) {
-+		dev_err(&pdev->dev, "could not remap memory\n");
-+		goto out_free_bi;
-+	}
-+
-+	bi->irq = irq;
-+	bi->clk = clk;
-+
-+	err = request_irq(irq, bcm2708_i2c_interrupt, IRQF_SHARED,
-+			dev_name(&pdev->dev), bi);
-+	if (err) {
-+		dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
-+		goto out_iounmap;
-+	}
-+
-+	bcm2708_bsc_reset(bi);
-+
-+	err = i2c_add_numbered_adapter(adap);
-+	if (err < 0) {
-+		dev_err(&pdev->dev, "could not add I2C adapter: %d\n", err);
-+		goto out_free_irq;
-+	}
-+
-+	bus_hz = clk_get_rate(bi->clk);
-+	cdiv = bus_hz / baudrate;
-+	if (cdiv > 0xffff) {
-+		cdiv = 0xffff;
-+		baudrate = bus_hz / cdiv;
-+	}
-+	bi->cdiv = cdiv;
-+
-+	dev_info(&pdev->dev, "BSC%d Controller at 0x%08lx (irq %d) (baudrate %d)\n",
-+		pdev->id, (unsigned long)regs->start, irq, baudrate);
-+
-+	return 0;
-+
-+out_free_irq:
-+	free_irq(bi->irq, bi);
-+out_iounmap:
-+	iounmap(bi->base);
-+out_free_bi:
-+	kfree(bi);
-+out_clk_disable:
-+	clk_disable_unprepare(clk);
-+out_clk_put:
-+	clk_put(clk);
-+	return err;
-+}
-+
-+static int bcm2708_i2c_remove(struct platform_device *pdev)
-+{
-+	struct bcm2708_i2c *bi = platform_get_drvdata(pdev);
-+
-+	platform_set_drvdata(pdev, NULL);
-+
-+	i2c_del_adapter(&bi->adapter);
-+	free_irq(bi->irq, bi);
-+	iounmap(bi->base);
-+	clk_disable_unprepare(bi->clk);
-+	clk_put(bi->clk);
-+	kfree(bi);
-+
-+	return 0;
-+}
-+
-+static const struct of_device_id bcm2708_i2c_of_match[] = {
-+        { .compatible = "brcm,bcm2708-i2c" },
-+        {},
-+};
-+MODULE_DEVICE_TABLE(of, bcm2708_i2c_of_match);
-+
-+static struct platform_driver bcm2708_i2c_driver = {
-+	.driver		= {
-+		.name	= DRV_NAME,
-+		.owner	= THIS_MODULE,
-+		.of_match_table = bcm2708_i2c_of_match,
-+	},
-+	.probe		= bcm2708_i2c_probe,
-+	.remove		= bcm2708_i2c_remove,
-+};
-+
-+// module_platform_driver(bcm2708_i2c_driver);
-+
-+
-+static int __init bcm2708_i2c_init(void)
-+{
-+	return platform_driver_register(&bcm2708_i2c_driver);
-+}
-+
-+static void __exit bcm2708_i2c_exit(void)
-+{
-+	platform_driver_unregister(&bcm2708_i2c_driver);
-+}
-+
-+module_init(bcm2708_i2c_init);
-+module_exit(bcm2708_i2c_exit);
-+
-+
-+
-+MODULE_DESCRIPTION("BSC controller driver for Broadcom BCM2708");
-+MODULE_AUTHOR("Chris Boot <bootc@bootc.net>");
-+MODULE_LICENSE("GPL v2");
-+MODULE_ALIAS("platform:" DRV_NAME);