brcm2708: add kernel 4.14 support

Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89

Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""

Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
  MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch

Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.

Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

1 files changed, 259 insertions, 0 deletions

diff --git a/target/linux/brcm2708/patches-4.14/950-0049-Add-cpufreq-driver.patch b/target/linux/brcm2708/patches-4.14/950-0049-Add-cpufreq-driver.patch
new file mode 100644
index 0000000000..4886d28ffe
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.14/950-0049-Add-cpufreq-driver.patch
@@ -0,0 +1,259 @@
+From 1466a5baed955602aa2f5283a41b3988794d3caf Mon Sep 17 00:00:00 2001
+From: popcornmix <popcornmix@gmail.com>
+Date: Wed, 3 Jul 2013 00:49:20 +0100
+Subject: [PATCH 049/454] Add cpufreq driver
+
+Signed-off-by: popcornmix <popcornmix@gmail.com>
+
+bcm2835-cpufreq: Change licence to GPLv2
+
+Signed-off-by: Eben Upton <eben.upton@broadcom.com>
+Signed-off-by: Dom Cobley <dom@raspberrypi.com>
+---
+ drivers/cpufreq/Kconfig.arm       |   9 ++
+ drivers/cpufreq/Makefile          |   1 +
+ drivers/cpufreq/bcm2835-cpufreq.c | 210 ++++++++++++++++++++++++++++++
+ 3 files changed, 220 insertions(+)
+ create mode 100644 drivers/cpufreq/bcm2835-cpufreq.c
+
+--- a/drivers/cpufreq/Kconfig.arm
++++ b/drivers/cpufreq/Kconfig.arm
+@@ -237,6 +237,15 @@ config ARM_TANGO_CPUFREQ
+ 	depends on CPUFREQ_DT && ARCH_TANGO
+ 	default y
+ 
++config ARM_BCM2835_CPUFREQ
++	depends on RASPBERRYPI_FIRMWARE
++	bool "BCM2835 Driver"
++	default y
++	help
++	  This adds the CPUFreq driver for BCM2835
++
++	  If in doubt, say N.
++
+ config ARM_TEGRA20_CPUFREQ
+ 	bool "Tegra20 CPUFreq support"
+ 	depends on ARCH_TEGRA
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -76,6 +76,7 @@ obj-$(CONFIG_ARM_SCPI_CPUFREQ)		+= scpi-
+ obj-$(CONFIG_ARM_SPEAR_CPUFREQ)		+= spear-cpufreq.o
+ obj-$(CONFIG_ARM_STI_CPUFREQ)		+= sti-cpufreq.o
+ obj-$(CONFIG_ARM_TANGO_CPUFREQ)		+= tango-cpufreq.o
++obj-$(CONFIG_ARM_BCM2835_CPUFREQ)	+= bcm2835-cpufreq.o
+ obj-$(CONFIG_ARM_TEGRA20_CPUFREQ)	+= tegra20-cpufreq.o
+ obj-$(CONFIG_ARM_TEGRA124_CPUFREQ)	+= tegra124-cpufreq.o
+ obj-$(CONFIG_ARM_TEGRA186_CPUFREQ)	+= tegra186-cpufreq.o
+--- /dev/null
++++ b/drivers/cpufreq/bcm2835-cpufreq.c
+@@ -0,0 +1,210 @@
++/*
++ * Copyright 2011 Broadcom Corporation.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; version 2
++ * of the License.
++ *
++ * This driver dynamically manages the CPU Frequency of the ARM
++ * processor. Messages are sent to Videocore either setting or requesting the
++ * frequency of the ARM in order to match an appropiate frequency to the current
++ * usage of the processor. The policy which selects the frequency to use is
++ * defined in the kernel .config file, but can be changed during runtime.
++ */
++
++/* ---------- INCLUDES ---------- */
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/cpufreq.h>
++#include <soc/bcm2835/raspberrypi-firmware.h>
++
++/* ---------- DEFINES ---------- */
++/*#define CPUFREQ_DEBUG_ENABLE*/		/* enable debugging */
++#define MODULE_NAME "bcm2835-cpufreq"
++
++#define VCMSG_ID_ARM_CLOCK 0x000000003		/* Clock/Voltage ID's */
++
++/* debug printk macros */
++#ifdef CPUFREQ_DEBUG_ENABLE
++#define print_debug(fmt,...) pr_debug("%s:%s:%d: "fmt, MODULE_NAME, __func__, __LINE__, ##__VA_ARGS__)
++#else
++#define print_debug(fmt,...)
++#endif
++#define print_err(fmt,...) pr_err("%s:%s:%d: "fmt, MODULE_NAME, __func__,__LINE__, ##__VA_ARGS__)
++#define print_info(fmt,...) pr_info("%s: "fmt, MODULE_NAME, ##__VA_ARGS__)
++
++/* ---------- GLOBALS ---------- */
++static struct cpufreq_driver bcm2835_cpufreq_driver;	/* the cpufreq driver global */
++static unsigned int min_frequency, max_frequency;
++static struct cpufreq_frequency_table bcm2835_freq_table[3];
++
++/*
++ ===============================================
++  clk_rate either gets or sets the clock rates.
++ ===============================================
++*/
++
++static int bcm2835_cpufreq_clock_property(u32 tag, u32 id, u32 *val)
++{
++	struct rpi_firmware *fw = rpi_firmware_get(NULL);
++	struct {
++		u32 id;
++		u32 val;
++	} packet;
++	int ret;
++
++	packet.id = id;
++	packet.val = *val;
++	ret = rpi_firmware_property(fw, tag, &packet, sizeof(packet));
++	if (ret)
++		return ret;
++
++	*val = packet.val;
++
++	return 0;
++}
++
++static uint32_t bcm2835_cpufreq_set_clock(int cur_rate, int arm_rate)
++{
++	u32 rate = arm_rate * 1000;
++	int ret;
++
++	ret = bcm2835_cpufreq_clock_property(RPI_FIRMWARE_SET_CLOCK_RATE, VCMSG_ID_ARM_CLOCK, &rate);
++	if (ret) {
++		print_err("Failed to set clock: %d (%d)\n", arm_rate, ret);
++		return 0;
++	}
++
++	rate /= 1000;
++	print_debug("Setting new frequency = %d -> %d (actual %d)\n", cur_rate, arm_rate, rate);
++
++	return rate;
++}
++
++static uint32_t bcm2835_cpufreq_get_clock(int tag)
++{
++	u32 rate;
++	int ret;
++
++	ret = bcm2835_cpufreq_clock_property(tag, VCMSG_ID_ARM_CLOCK, &rate);
++	if (ret) {
++		print_err("Failed to get clock (%d)\n", ret);
++		return 0;
++	}
++
++	rate /= 1000;
++	print_debug("%s frequency = %u\n",
++		tag == RPI_FIRMWARE_GET_CLOCK_RATE ? "Current":
++		tag == RPI_FIRMWARE_GET_MIN_CLOCK_RATE ? "Min":
++		tag == RPI_FIRMWARE_GET_MAX_CLOCK_RATE ? "Max":
++		"Unexpected", rate);
++
++	return rate;
++}
++
++/*
++ ====================================================
++  Module Initialisation registers the cpufreq driver
++ ====================================================
++*/
++static int __init bcm2835_cpufreq_module_init(void)
++{
++	print_debug("IN\n");
++	return cpufreq_register_driver(&bcm2835_cpufreq_driver);
++}
++
++/*
++ =============
++  Module exit
++ =============
++*/
++static void __exit bcm2835_cpufreq_module_exit(void)
++{
++	print_debug("IN\n");
++	cpufreq_unregister_driver(&bcm2835_cpufreq_driver);
++	return;
++}
++
++/*
++ ==============================================================
++  Initialisation function sets up the CPU policy for first use
++ ==============================================================
++*/
++static int bcm2835_cpufreq_driver_init(struct cpufreq_policy *policy)
++{
++	/* measured value of how long it takes to change frequency */
++	const unsigned int transition_latency = 355000; /* ns */
++
++	if (!rpi_firmware_get(NULL)) {
++		print_err("Firmware is not available\n");
++		return -ENODEV;
++	}
++
++	/* now find out what the maximum and minimum frequencies are */
++	min_frequency = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
++	max_frequency = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
++
++	if (min_frequency == max_frequency) {
++		bcm2835_freq_table[0].frequency = min_frequency;
++		bcm2835_freq_table[1].frequency = CPUFREQ_TABLE_END;
++	} else {
++		bcm2835_freq_table[0].frequency = min_frequency;
++		bcm2835_freq_table[1].frequency = max_frequency;
++		bcm2835_freq_table[2].frequency = CPUFREQ_TABLE_END;
++	}
++
++	print_info("min=%d max=%d\n", min_frequency, max_frequency);
++	return cpufreq_generic_init(policy, bcm2835_freq_table, transition_latency);
++}
++
++/*
++ =====================================================================
++  Target index function chooses the requested frequency from the table
++ =====================================================================
++*/
++
++static int bcm2835_cpufreq_driver_target_index(struct cpufreq_policy *policy, unsigned int state)
++{
++	unsigned int target_freq = state == 0 ? min_frequency : max_frequency;
++	unsigned int cur = bcm2835_cpufreq_set_clock(policy->cur, target_freq);
++
++	if (!cur)
++	{
++		print_err("Error occurred setting a new frequency (%d)\n", target_freq);
++		return -EINVAL;
++	}
++	print_debug("%s: %i: freq %d->%d\n", policy->governor->name, state, policy->cur, cur);
++	return 0;
++}
++
++/*
++ ======================================================
++  Get function returns the current frequency from table
++ ======================================================
++*/
++
++static unsigned int bcm2835_cpufreq_driver_get(unsigned int cpu)
++{
++	unsigned int actual_rate = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
++	print_debug("cpu%d: freq=%d\n", cpu, actual_rate);
++	return actual_rate <= min_frequency ? min_frequency : max_frequency;
++}
++
++/* the CPUFreq driver */
++static struct cpufreq_driver bcm2835_cpufreq_driver = {
++	.name         = "BCM2835 CPUFreq",
++	.init         = bcm2835_cpufreq_driver_init,
++	.verify       = cpufreq_generic_frequency_table_verify,
++	.target_index = bcm2835_cpufreq_driver_target_index,
++	.get          = bcm2835_cpufreq_driver_get,
++	.attr         = cpufreq_generic_attr,
++};
++
++MODULE_AUTHOR("Dorian Peake and Dom Cobley");
++MODULE_DESCRIPTION("CPU frequency driver for BCM2835 chip");
++MODULE_LICENSE("GPL");
++
++module_init(bcm2835_cpufreq_module_init);
++module_exit(bcm2835_cpufreq_module_exit);