bcm63xx: add support for Technicolor TG582n Telecom Italia branded

Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.

Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)

Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
  .bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file

PCB:   |GPIO:   |TG582n:          |AGTWI:

LED2R  |488(08) |red    Power     |red   Power
LED2G  |484(04) |green  Power     |green Power

LED10R |486(06) |                 |missing R85 end LED
LED13G |485(05) |green  Ethernet  |green ADSL

LED11R |494(14) |                 |red   Internet
LED14G |491(11) |green  Broadband |green Internet

LED5R  |487(07) |red    Internet  |red   Wi-Fi
LED5G  |481(01) |green  Internet  |green Wi-Fi

LED12R |498(18) |                 |red   Service
LED12G |499(19) |                 |green Service

LED6R  |482(02) |red    Wi-Fi     |missing R108 end LED
LED6G  |483(03) |green  Wi-Fi     |missing R107 end LED

LED7R  |490(10) |red    WPS       |missing R91 end LED
LED7G  |489(09) |green  WPS       |missing R92 end LED

LED4   |508(28) |ethernet port 4  |ethernet port 4
LED3   |507(27) |ethernet port 3  |ethernet port 3

LED9   |506(26) |ethernet port 2  |ethernet port 2
LED8   |505(25) |ethernet port 1  |ethernet port 1

SW3    |503(23) |key Reset        |key Reset

SW5    |504(24) |key WPS          |key Wi-Fi/LED

SW4    |495(15) |key Wi-Fi        |missing R127 end key

SW6    |493(13) |                 |missing R171 end key

SW1    |492(12) |                 |missing R1 end key

Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

1 files changed, 48 insertions, 3 deletions

diff --git a/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch b/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch
index a8c13dedd9..ebe1ac4d94 100644
--- a/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch
+++ b/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch
@@ -1,6 +1,6 @@
 --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
 +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -348,6 +348,525 @@ static struct board_info __initdata boar
+@@ -348,6 +348,568 @@ static struct board_info __initdata boar
  		},
  	},
  };
@@ -523,10 +523,53 @@
 +		.pci_dev = 0,
 +	},
 +};
++
++static struct board_info __initdata board_TG582N_TELECOM_ITALIA = {
++	.name = "DANT-V",
++	.expected_cpu_id = 0x6328,
++
++	.has_pci = 1,
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++	.num_usbh_ports = 1,
++
++	.has_enetsw = 1,
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used = 1,
++				.phy_id = 1,
++				.name = "Port 1",
++			},
++			[1] = {
++				.used = 1,
++				.phy_id = 2,
++				.name = "Port 2",
++			},
++			[2] = {
++				.used = 1,
++				.phy_id = 3,
++				.name = "Port 3",
++			},
++			[3] = {
++				.used = 1,
++				.phy_id = 4,
++				.name = "Port 4",
++			},
++		},
++	},
++
++	.use_fallback_sprom = 1,
++	.fallback_sprom = {
++		.type = SPROM_BCM43225,
++		.pci_bus = 1,
++		.pci_dev = 0,
++	},
++};
  #endif /* CONFIG_BCM63XX_CPU_6328 */
  
  /*
-@@ -703,6 +1222,17 @@ static const struct board_info __initcon
+@@ -703,6 +1265,18 @@ static const struct board_info __initcon
  #endif /* CONFIG_BCM63XX_CPU_6318 */
  #ifdef CONFIG_BCM63XX_CPU_6328
  	&board_96328avng,
@@ -540,11 +583,12 @@
 +	&board_FAST2704V2,
 +	&board_PDG_A4001N_A_000_1A1_AX,
 +	&board_PDG_A4101N_A_000_1A1_AE,
++	&board_TG582N_TELECOM_ITALIA,
 +	&board_R5010UNV2,
  #endif /* CONFIG_BCM63XX_CPU_6328 */
  #ifdef CONFIG_BCM63XX_CPU_6338
  	&board_96338gw,
-@@ -742,7 +1272,20 @@ static struct of_device_id const bcm963x
+@@ -742,7 +1316,21 @@ static struct of_device_id const bcm963x
  	{ .compatible = "sagem,fast-2704n", .data = &board_FAST2704N, },
  #endif /* CONFIG_BCM63XX_CPU_6318 */
  #ifdef CONFIG_BCM63XX_CPU_6328
@@ -562,6 +606,7 @@
 +	{ .compatible = "sagem,fast-2704-v2", .data = &board_FAST2704V2, },
 +	{ .compatible = "sercomm,ad1018", .data = &board_AD1018, },
 +	{ .compatible = "sercomm,ad1018-nor", .data = &board_AD1018, },
++	{ .compatible = "technicolor,tg582n-telecom-italia", .data = &board_TG582N_TELECOM_ITALIA, },
  #endif /* CONFIG_BCM63XX_CPU_6328 */
  #ifdef CONFIG_BCM63XX_CPU_6338
  	{ .compatible = "brcm,bcm96338gw", .data = &board_96338gw, },