kernel: bump 5.15 to 5.15.62

Deleted following upstreamed patches:

 bcm27xx: 950-0006-drm-vc4-hdmi-Fix-HPD-GPIO-detection.patch
 bcm27xx: 950-0420-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
 bcm27xx: 950-0425-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
 bcm27xx: 950-0432-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
 bcm27xx: 950-0433-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
 bcm27xx: 950-0435-drm-vc4-Correct-pixel-order-for-DSI0.patch
 bcm27xx: 950-0436-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
 bcm27xx: 950-0437-drm-vc4-Fix-dsi0-interrupt-support.patch
 bcm27xx: 950-0438-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
 bcm27xx: 950-0443-drm-vc4-Fix-timings-for-interlaced-modes.patch
 bcm27xx: 950-0445-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
 bcm27xx: 950-0475-drm-vc4-Reset-HDMI-MISC_CONTROL-register.patch
 bcm27xx: 950-0476-drm-vc4-Release-workaround-buffer-and-DMA-in-error-p.patch
 bcm27xx: 950-0477-drm-vc4-Correct-DSI-divider-calculations.patch
 bcm27xx: 950-0664-drm-vc4-dsi-Correct-max-divider-to-255-not-7.patch

 bcm53xx: 072-next-ARM_dts_BCM53015-add-mr26.patch

 mediatek: 920-linux-next-dts-mt7622-bpi-r64-fix-wps-button.patch

Manually rebased following patches:

 bcm27xx: 950-0004-drm-vc4-hdmi-Remove-the-DDC-probing-for-status-detec.patch
 bcm27xx: 950-0700-net-phy-lan87xx-Decrease-phy-polling-rate.patch
 bcm27xx: 950-0711-drm-vc4-Rename-bridge-to-out_bridge.patch
 bcm27xx: 950-0713-drm-vc4-Remove-splitting-the-bridge-chain-from-the-d.patch
 bcm27xx: 950-0715-drm-vc4-Convert-vc4_dsi-to-using-a-bridge-instead-of.patch
 bcm27xx: 950-0787-vc4-drm-vc4_plane-Keep-fractional-source-coords-insi.patch
 bcm27xx: 950-0914-mmc-block-Don-t-do-single-sector-reads-during-recove.patch

Runtime tested on turris-omnia and glinet-b1300.

Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>

3 files changed, 2 insertions, 244 deletions

diff --git a/target/linux/bcm53xx/patches-5.15/030-v5.15-0008-ARM-dts-NSP-Add-DT-files-for-Meraki-MX64-series.patch b/target/linux/bcm53xx/patches-5.15/030-v5.15-0008-ARM-dts-NSP-Add-DT-files-for-Meraki-MX64-series.patch
index 813dfa2930..ffdd64fb59 100644
--- a/target/linux/bcm53xx/patches-5.15/030-v5.15-0008-ARM-dts-NSP-Add-DT-files-for-Meraki-MX64-series.patch
+++ b/target/linux/bcm53xx/patches-5.15/030-v5.15-0008-ARM-dts-NSP-Add-DT-files-for-Meraki-MX64-series.patch
@@ -35,7 +35,7 @@ Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -157,6 +157,10 @@ dtb-$(CONFIG_ARCH_BCM_NSP) += \
+@@ -158,6 +158,10 @@ dtb-$(CONFIG_ARCH_BCM_NSP) += \
  	bcm958525xmc.dtb \
  	bcm958622hr.dtb \
  	bcm958623hr.dtb \
diff --git a/target/linux/bcm53xx/patches-5.15/030-v5.15-0009-ARM-dts-NSP-Add-DT-files-for-Meraki-MX65-series.patch b/target/linux/bcm53xx/patches-5.15/030-v5.15-0009-ARM-dts-NSP-Add-DT-files-for-Meraki-MX65-series.patch
index 6e0ab96b71..29f8b5d0fe 100644
--- a/target/linux/bcm53xx/patches-5.15/030-v5.15-0009-ARM-dts-NSP-Add-DT-files-for-Meraki-MX65-series.patch
+++ b/target/linux/bcm53xx/patches-5.15/030-v5.15-0009-ARM-dts-NSP-Add-DT-files-for-Meraki-MX65-series.patch
@@ -31,7 +31,7 @@ Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -161,6 +161,8 @@ dtb-$(CONFIG_ARCH_BCM_NSP) += \
+@@ -162,6 +162,8 @@ dtb-$(CONFIG_ARCH_BCM_NSP) += \
  	bcm958625-meraki-mx64-a0.dtb \
  	bcm958625-meraki-mx64w.dtb \
  	bcm958625-meraki-mx64w-a0.dtb \
diff --git a/target/linux/bcm53xx/patches-5.15/072-next-ARM_dts_BCM53015-add-mr26.patch b/target/linux/bcm53xx/patches-5.15/072-next-ARM_dts_BCM53015-add-mr26.patch
deleted file mode 100644
index c85f27282d..0000000000
--- a/target/linux/bcm53xx/patches-5.15/072-next-ARM_dts_BCM53015-add-mr26.patch
+++ /dev/null
@@ -1,242 +0,0 @@
-From 935327a73553001f8d81375c76985d05f604507f Mon Sep 17 00:00:00 2001
-From: Christian Lamparter <chunkeey@gmail.com>
-Date: Sat, 18 Jun 2022 00:00:29 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Meraki MR26
-
-Meraki MR26 is an EOL wireless access point featuring a
-PoE ethernet port and two dual-band 3x3 MIMO 802.11n
-radios and 1x1 dual-band WIFI dedicated to scanning.
-
-Thank you Amir for the unit and PSU.
-
-Hardware info:
-SOC   : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
-RAM   : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
-NAND  : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
-ETH   : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
-WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
-WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
-WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
-BUTTON: One reset key behind a small hole next to the Ethernet Port
-LEDS  : One amber (fault), one white (indicator) LED, separate RGB-LED
-MISC  : Atmel AT24C64 8KiB EEPROM i2c
-      : Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
-
-SERIAL:
-      WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
-      The Serial setting is 115200-8-N-1. The board has a populated
-      right angle 1x4 0.1" pinheader.
-      The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
-
-Odd stuff:
-
-- uboot does not support lzma compression, but gzip'd uImage/DTB work.
-- uboot claims to support FIT, but fails to pass the DTB to the kernel.
-  Appending the dtb after the kernel image works.
-- RGB-controller is supported through an external userspace program.
-- The ubi partition contains a "board-config" volume. It stores the
-  MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
-- SoC's temperature sensor always reports that it is on fire.
-  This causes the system to immediately shutdown! Looking at reported
-  "418 degree Celsius" suggests that this sensor is not working.
-
-WIFI:
-b43 is able to initialize all three WIFIs @ 802.11bg.
-| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
-| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
-| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
-| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
-| b43-phy0 warning: 5 GHz band is unsupported on this PHY
-| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
-| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
-| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
-| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
-| b43-phy1 warning: 5 GHz band is unsupported on this PHY
-| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
-| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
-| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
-| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
-| Broadcom 43xx driver loaded [ Features: NL ]
-
-Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
-Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
----
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
-@@ -0,0 +1,166 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Broadcom BCM470X / BCM5301X ARM platform code.
-+ * DTS for Meraki MR26 / Codename: Venom
-+ *
-+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm4708.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+#include <dt-bindings/leds/common.h>
-+
-+/ {
-+	compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
-+	model = "Meraki MR26";
-+
-+	memory@0 {
-+		reg = <0x00000000 0x08000000>;
-+		device_type = "memory";
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		led-0 {
-+			function = LED_FUNCTION_FAULT;
-+			color = <LED_COLOR_ID_AMBER>;
-+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
-+			panic-indicator;
-+		};
-+		led-1 {
-+			function = LED_FUNCTION_INDICATOR;
-+			color = <LED_COLOR_ID_WHITE>;
-+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+
-+	keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		key-restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&uart0 {
-+	clock-frequency = <50000000>;
-+	/delete-property/ clocks;
-+};
-+
-+&uart1 {
-+	status = "disabled";
-+};
-+
-+&gmac0 {
-+	status = "okay";
-+};
-+
-+&gmac1 {
-+	status = "disabled";
-+};
-+&gmac2 {
-+	status = "disabled";
-+};
-+&gmac3 {
-+	status = "disabled";
-+};
-+
-+&nandcs {
-+	nand-ecc-algo = "hw";
-+
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <0x1>;
-+		#size-cells = <0x1>;
-+
-+		partition@0 {
-+			label = "u-boot";
-+			reg = <0x0 0x200000>;
-+			read-only;
-+		};
-+
-+		partition@200000 {
-+			label = "u-boot-env";
-+			reg = <0x200000 0x200000>;
-+			/* empty */
-+		};
-+
-+		partition@400000 {
-+			label = "u-boot-backup";
-+			reg = <0x400000 0x200000>;
-+			/* empty */
-+		};
-+
-+		partition@600000 {
-+			label = "u-boot-env-backup";
-+			reg = <0x600000 0x200000>;
-+			/* empty */
-+		};
-+
-+		partition@800000 {
-+			label = "ubi";
-+			reg = <0x800000 0x7780000>;
-+		};
-+	};
-+};
-+
-+&srab {
-+	status = "okay";
-+
-+	ports {
-+		port@0 {
-+			reg = <0>;
-+			label = "poe";
-+		};
-+
-+		port@5 {
-+			reg = <5>;
-+			label = "cpu";
-+			ethernet = <&gmac0>;
-+
-+			fixed-link {
-+				speed = <1000>;
-+				duplex-full;
-+			};
-+		};
-+	};
-+};
-+
-+&i2c0 {
-+	status = "okay";
-+
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinmux_i2c>;
-+
-+	clock-frequency = <100000>;
-+
-+	ina219@40 {
-+		compatible = "ti,ina219"; /* PoE power */
-+		reg = <0x40>;
-+		shunt-resistor = <60000>; /* = 60 mOhms */
-+	};
-+
-+	eeprom@56 {
-+		compatible = "atmel,24c64";
-+		reg = <0x56>;
-+		pagesize = <32>;
-+		read-only;
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		/* it's empty */
-+	};
-+};
-+
-+&thermal {
-+	status = "disabled";
-+	/* does not work, reads 418 degree Celsius */
-+};
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -128,6 +128,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm47094-luxul-xwr-3150-v1.dtb \
- 	bcm47094-netgear-r8500.dtb \
- 	bcm47094-phicomm-k3.dtb \
-+	bcm53015-meraki-mr26.dtb \
- 	bcm53016-meraki-mr32.dtb \
- 	bcm94708.dtb \
- 	bcm94709.dtb \