bcm53xx: switch to the upstream DSA-based b53 driver

1. Drop swconfig
2. Simplify network setup
3. Verify network config
4. Disable Buffalo WZR-900DHP for now - it misses ports definition

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-By: Christian Lamparter <chunkeey@gmail.com>

2 files changed, 32 insertions, 71 deletions

diff --git a/target/linux/bcm53xx/base-files/etc/board.d/02_network b/target/linux/bcm53xx/base-files/etc/board.d/02_network
index e02286027f..9308801b85 100644
--- a/target/linux/bcm53xx/base-files/etc/board.d/02_network
+++ b/target/linux/bcm53xx/base-files/etc/board.d/02_network
@@ -9,74 +9,24 @@ bcm53xx_setup_interfaces()
 {
 	local board="$1"
 
-	# On BCM4708 / BCM4709(4) there are 3 Ethernet interfaces connected to 3 switch
-	# ports. It's up to vendor which to use.
 	case "$board" in
-	tenda,ac9)
-		ucidef_add_switch "switch0" \
-			"1:lan" "2:lan" "3:lan" "4:lan" "8@eth0" "0:wan" "5@eth1"
-		;;
-	buffalo,wxr-1900dhp| \
-	buffalo,wzr-1750dhp)
-		ucidef_add_switch "switch0" \
-			"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan:5" "5@eth0"
-		;;
-	dlink,dir-885l | \
-	netgear,r7900 | \
-	netgear,r8000 | \
-	netgear,r8500)
-		# NVRAM specifies port 8 (eth2) - unsupported by OpenWrt b53
-		# Use port 5 (eth0) as workaround
-		ucidef_add_switch "switch0" \
-			"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5t@eth0"
+	asus,rt-ac87u)
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
 		;;
 	linksys,panamera)
-		ucidef_add_switch "switch1" \
-			"0:lan" "1:lan:7" "2:lan:4" "3:lan:8" "4:wan" "5t@eth0"
-		;;
-	luxul,abr-4500-v1|\
-	luxul,xbr-4500-v1)
-		ucidef_add_switch "switch0" \
-			"0:wan" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5@eth0"
+		ucidef_set_interfaces_lan_wan "lan4 lan7 lan8 extsw" "wan"
 		;;
 	luxul,xap-1610-v1)
-		ucidef_add_switch "switch0" \
-			"0:lan" "1:lan" "5@eth0"
-		ucidef_set_interface_lan "eth0.1" "dhcp"
+		ucidef_set_interface_lan "poe lan" "dhcp"
 		;;
-	luxul,xwr-3150-v1)
-		ucidef_add_switch "switch0" \
-			"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "5@eth0"
+	meraki,mr32)
+		ucidef_set_interface_lan "poe" "dhcp"
 		;;
 	phicomm,k3)
-		ucidef_add_switch "switch0" \
-			"0:lan" "1:lan" "2:lan" "3:wan" "5@eth0"
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
 		;;
 	*)
-		# NVRAM entries may contain unsorted ports, e.g. Netgear R6250 uses
-		# vlan1ports=3 2 1 0 5*
-		# vlan2ports=4 5u
-		# and early Netgear R8000 was using
-		# vlan1ports=3 2 1 0 5 7 8*
-		# (the enclosing echo is needed to convert newline back to space)
-		vlan1ports="$(echo $(nvram get vlan1ports | tr " " "\n" | sort))"
-		vlan2ports="$(echo $(nvram get vlan2ports | tr " " "\n" | sort))"
-		if echo "$vlan1ports" | egrep -q "^1 2 3 4 5" && \
-		   echo "$vlan2ports" | egrep -q "^0 5"; then
-			ucidef_add_switch "switch0" \
-				"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5t@eth0"
-		elif echo "$vlan1ports" | egrep -q "^1 2 3 5 7" && \
-		     echo "$vlan2ports" | egrep -q "^0 7"; then
-			ucidef_add_switch "switch0" \
-				"1:lan" "2:lan" "3:lan" "5:lan" "0:wan" "7t@eth1"
-		elif echo "$vlan1ports" | egrep -q "^0 1 2 3 5 7 8" && \
-		     echo "$vlan2ports" | egrep -q "^4 8"; then
-			ucidef_add_switch "switch0" \
-				"0:lan" "1:lan" "2:lan" "3:lan" "5:lan" "7:lan" "4:wan" "8t@eth2"
-		else
-			ucidef_add_switch "switch0" \
-				"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5t@eth0"
-		fi
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
 		;;
 	esac
 }
@@ -85,20 +35,8 @@ bcm53xx_setup_macs()
 {
 	local board="$1"
 
-	case "$board" in
-	dlink,dir-885l | \
-	linksys,panamera | \
-	netgear,r7900 | \
-	netgear,r8000 | \
-	netgear,r8500)
-		# As vendor doesn't use eth0 its MAC may be missing. Use one from eth2.
-		et2macaddr="$(nvram get et2macaddr)"
-		;;
-	esac
-
-	[ -n "$et2macaddr" ] && ucidef_set_interface_macaddr "lan" "$et2macaddr"
-
 	wan_macaddr="$(nvram get wan_hwaddr)"
+
 	case "$board" in
 	asus,rt-ac87u)
 		etXmacaddr=$(nvram get et1macaddr)
diff --git a/target/linux/bcm53xx/base-files/etc/uci-defaults/03_dsa_migrate b/target/linux/bcm53xx/base-files/etc/uci-defaults/03_dsa_migrate
new file mode 100644
index 0000000000..7350f57e5d
--- /dev/null
+++ b/target/linux/bcm53xx/base-files/etc/uci-defaults/03_dsa_migrate
@@ -0,0 +1,23 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+# Exit if network doesn't contain any swconfig section
+uci -q get network.@switch[0] > /dev/null || exit 0
+
+lan_proto="$(uci -q get network.lan.proto)"
+lan_ipaddr="$(uci -q get network.lan.ipaddr)"
+lan_netmask="$(uci -q get network.lan.netmask)"
+wan_proto="$(uci -q get network.wan.proto)"
+wan_ipaddr="$(uci -q get network.wan.ipaddr)"
+wan_netmask="$(uci -q get network.wan.netmask)"
+
+rm /etc/config/network
+config_generate
+
+uci -q batch <<-EOF
+	set network.lan.proto="$lan_proto"
+	set network.lan.ipaddr="$lan_ipaddr"
+	set network.lan.netmask="$lan_netmask"
+	set network.wan.proto="$wan_proto"
+	set network.wan.ipaddr="$wan_ipaddr"
+	set network.wan.netmask="$wan_netmask"
+EOF