bcm27xx: update patches from RPi foundation

bcm2708: boot tested on RPi B+ v1.2
bcm2709: boot tested on RPi 3B v1.2
bcm2710: boot tested on RPi 3B v1.2
bcm2711: boot tested on RPi 4B v1.1 4G

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

1 files changed, 0 insertions, 45 deletions

diff --git a/target/linux/bcm27xx/patches-5.4/950-0474-gpio-ir-overlay-add-parameter-to-configure-signal-po.patch b/target/linux/bcm27xx/patches-5.4/950-0474-gpio-ir-overlay-add-parameter-to-configure-signal-po.patch
deleted file mode 100644
index cdd14f7940..0000000000
--- a/target/linux/bcm27xx/patches-5.4/950-0474-gpio-ir-overlay-add-parameter-to-configure-signal-po.patch
+++ /dev/null
@@ -1,45 +0,0 @@
-From e253d03936265dc4ab8ae9ae89d2a885e80a45a6 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias@horus.com>
-Date: Fri, 6 Mar 2020 11:08:10 +0100
-Subject: [PATCH] gpio-ir-overlay: add parameter to configure signal
- polarity (#3490)
-
-Standard IR receivers use inverted / active-low signalling
-and the gpio-ir overlay configures the GPIO appropriately
-as GPIO_ACTIVE_LOW (1).
-
-In order to support (rather rare) non-inverted / active-high
-signalling the GPIO needs to be configured as GPIO_ACTIVE_HIGH (0).
-
-Add an "invert" parameter to override this like in the gpio-ir-tx
-overlay.
-
-Signed-off-by: Matthias Reichl <hias@horus.com>
----
- arch/arm/boot/dts/overlays/README              | 4 ++++
- arch/arm/boot/dts/overlays/gpio-ir-overlay.dts | 1 +
- 2 files changed, 5 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -754,6 +754,10 @@ Params: gpio_pin                Input pi
-         gpio_pull               Desired pull-up/down state (off, down, up)
-                                 Default is "up".
- 
-+        invert                  "1" = invert the input (active-low signalling).
-+                                "0" = non-inverted input (active-high
-+                                signalling). Default is "1".
-+
-         rc-map-name             Default rc keymap (can also be changed by
-                                 ir-keytable), defaults to "rc-rc6-mce"
- 
---- a/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-@@ -42,6 +42,7 @@
-                                 <&gpio_ir_pins>,"brcm,pins:0",
-                                 <&gpio_ir_pins>,"reg:0";
-                 gpio_pull = <&gpio_ir_pins>,"brcm,pull:0";              // pull-up/down state
-+                invert = <&gpio_ir>,"gpios:8";                          // 0 = active high input
- 
-                 rc-map-name = <&gpio_ir>,"linux,rc-map-name";           // default rc map
-         };