brcm2708: rename target to bcm27xx

This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.

Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).

This also renames the packages brcm2708-userland and brcm2708-gpu-fw.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>

1 files changed, 66 insertions, 0 deletions

diff --git a/target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch b/target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch
new file mode 100644
index 0000000000..4291f9fee5
--- /dev/null
+++ b/target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch
@@ -0,0 +1,66 @@
+From b4f8b92cdfd8ad2e04cdd3f0a73aa4e95d172fb1 Mon Sep 17 00:00:00 2001
+From: Markus Proeller <markus.proeller@pieye.org>
+Date: Thu, 10 Oct 2019 19:12:08 +0200
+Subject: [PATCH] dt-bindings: Add binding for the Infineon IRS1125
+ sensor
+
+Adds a binding for the Infineon IRS1125 time-of-flight depth
+sensor.
+
+Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
+---
+ .../devicetree/bindings/media/i2c/irs1125.txt | 48 +++++++++++++++++++
+ 1 file changed, 48 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/media/i2c/irs1125.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/media/i2c/irs1125.txt
+@@ -0,0 +1,48 @@
++* Infineon irs1125 time of flight sensor
++
++The Infineon irs1125 is a time of flight digital image sensor with
++an active array size of 352H x 286V. It is programmable through I2C
++interface. The I2C address defaults to 0x3D, but can be reconfigured
++to address 0x3C or 0x41 via I2C commands. Image data is sent through
++MIPI CSI-2, which is configured as either 1 or 2 data lanes.
++
++Required Properties:
++- compatible: value should be "infineon,irs1125" for irs1125 sensor
++- reg: I2C bus address of the device
++- clocks: reference to the xclk input clock.
++- pwdn-gpios: reference to the GPIO connected to the reset pin.
++	      This is an active low signal to the iirs1125.
++
++The irs1125 device node should contain one 'port' child node with
++an 'endpoint' subnode. For further reading on port node refer to
++Documentation/devicetree/bindings/media/video-interfaces.txt.
++
++Endpoint node required properties for CSI-2 connection are:
++- remote-endpoint: a phandle to the bus receiver's endpoint node.
++- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
++- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2
++  supported)
++
++Example:
++	sensor@10 {
++		compatible = "infineon,irs1125";
++		reg = <0x3D>;
++		#address-cells = <1>;
++		#size-cells = <0>;
++		clocks = <&irs1125_clk>;
++		pwdn-gpios = <&gpio 5 0>;
++
++		irs1125_clk: camera-clk {
++			compatible = "fixed-clock";
++			#clock-cells = <0>;
++			clock-frequency = <26000000>;
++		};
++
++		port {
++			sensor_out: endpoint {
++				remote-endpoint = <&csiss_in>;
++				clock-lanes = <0>;
++				data-lanes = <1 2>;
++			};
++		};
++	};