aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
diff options
context:
space:
mode:
authorChristian Lamparter <chunkeey@gmail.com>2021-07-30 17:59:25 +0200
committerChristian Lamparter <chunkeey@gmail.com>2023-05-14 00:08:35 +0200
commit1d49310fdb5e6febd2e7a60d55deb0adb4364307 (patch)
treef1c9b003fd8dbcf1ca46349b44cf5628567f5b8d /target/linux/ath79
parentcb9ccd644bf986d5c23e40dda92576d36a1d3b1b (diff)
downloadupstream-1d49310fdb5e6febd2e7a60d55deb0adb4364307.tar.gz
upstream-1d49310fdb5e6febd2e7a60d55deb0adb4364307.tar.bz2
upstream-1d49310fdb5e6febd2e7a60d55deb0adb4364307.zip
ath79: add Cisco Meraki MR18
Specifications: SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz RAM: 2x Winbond W9751G6KB-25 (128 MiB) FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB) WIFI1: Atheros AR9550 5.0GHz (SoC) WIFI2: Atheros AR9582-AR1A 2.4GHz WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN) LED: 1x Power-LED, 1 x RGB Tricolor-LED INPUT: One Reset Button UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8 (VCC, RX, TX, GND - VCC is closest to the boot set jumper under the console pins.) Flashing instructions: Depending on the installed firmware, there are vastly different methods to flash a MR18. These have been documented on: <https://openwrt.org/toh/meraki/mr18> Tip: Use an initramfs from a previous release and then use sysupgrade to get to the later releases. This is because the initramfs can no longer be built by the build-bots due to its size (>8 MiB). Note on that: Upgrades from AR71XX releases are possible, but they will require the force sysupgrade option ( -F ). Please backup your MR18's configuration before starting the update. The reason here is that a lot of development happend since AR71XX got removed, so I do advise to use the ( -n ) option for sysupgrade as well. This will cause the device to drop the old AR71xx configuration and make a new configurations from scratch. Note on LEDs: The LEDs has changed since AR71XX. The white LED is now used during the boot and when upgrading instead of the green tricolor LED. The technical reason is that currently the RGB-LED is brought up later by a userspace daemon. (added warning note about odm-caldata partition. remove initramfs - it's too big to be built by the bots. MerakiNAND -> meraki-header. sort nu801's targets) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ath79')
-rw-r--r--target/linux/ath79/dts/qca9557_meraki_mr18.dts203
-rw-r--r--target/linux/ath79/image/lzma-loader/src/ar71xx_regs.h17
-rw-r--r--target/linux/ath79/image/lzma-loader/src/board.c133
-rw-r--r--target/linux/ath79/image/nand.mk25
-rw-r--r--target/linux/ath79/nand/base-files/etc/board.d/02_network6
-rw-r--r--target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom44
6 files changed, 427 insertions, 1 deletions
diff --git a/target/linux/ath79/dts/qca9557_meraki_mr18.dts b/target/linux/ath79/dts/qca9557_meraki_mr18.dts
new file mode 100644
index 0000000000..a88e2bcd37
--- /dev/null
+++ b/target/linux/ath79/dts/qca9557_meraki_mr18.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "meraki,mr18", "qca,qca9558";
+ model = "Meraki MR18";
+
+ aliases {
+ label-mac-device = &eth0;
+ led-boot = &white;
+ led-failsafe = &orange;
+ led-running = &green;
+ led-upgrade = &white;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ white: white {
+ label = "white:power";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+
+ orange: orange {
+ label = "orange:power";
+ gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+ };
+
+ uleds {
+ compatible = "virtual-leds";
+#if 0
+ /*
+ * RGB leds are not supported by uleds driver.
+ * but this is what the definitions for a as
+ * of yet unwritten leds_nu801 would look like.
+ */
+
+ rgbled-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RGB>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ green: led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+
+#else
+ red {
+ label = "red:tricolor";
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ green: green {
+ label = "green:tricolor";
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ blue {
+ label = "blue:tricolor";
+ color = <LED_COLOR_ID_BLUE>;
+ };
+#endif
+ };
+
+ button {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ };
+};
+
+&nand {
+ status = "okay";
+
+ nand-ecc-mode = "soft";
+ nand-ecc-algo = "bch";
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-is-boot-medium;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "nandloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "kernel";
+ reg = <0x80000 0x800000>;
+ };
+
+ partition@880000 {
+ label = "recovery";
+ reg = <0x880000 0x800000>;
+ };
+
+ partition@1080000 {
+ label = "ubi";
+ reg = <0x1080000 0x6f00000>;
+ };
+
+ partition@7fe0000 {
+ /*
+ * This is not always present. And if
+ * it is, then Meraki (or contractor)
+ * used a different ecc method than
+ * the one we need for the UBI partition.
+ * Reading this causes various reading
+ * errors.
+ *
+ * As a result: Please don't convert
+ * this to nvmem-cells. Instead there's
+ * a ubi-volume "caldata" that has the
+ * necessary data.
+ */
+
+ label = "odm-caldata";
+ reg = <0x7fe0000 0x20000>;
+ read-only;
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "pci168c,0033";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ };
+};
+
+&pcie1 {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "pci168c,0033";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy: ethernet-phy@3 {
+ reg = <3>;
+ };
+};
+
+&eth0 {
+ status = "okay";
+ pll-data = <0xa6000000 0xa0000101 0x80001313>;
+ phy-handle = <&phy>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-enabled = <1>;
+ rxd-delay = <3>;
+ rxdv-delay = <3>;
+ };
+};
+
+&wmac {
+ status = "okay";
+ qca,no-eeprom;
+};
diff --git a/target/linux/ath79/image/lzma-loader/src/ar71xx_regs.h b/target/linux/ath79/image/lzma-loader/src/ar71xx_regs.h
index 19a4785bb4..245042fdab 100644
--- a/target/linux/ath79/image/lzma-loader/src/ar71xx_regs.h
+++ b/target/linux/ath79/image/lzma-loader/src/ar71xx_regs.h
@@ -128,6 +128,17 @@
#define AR9300_OTP_STATUS_SM_BUSY 0x1
#define AR9300_OTP_READ_DATA 0x15f1c
+#define QCA955X_OTP_BASE (AR71XX_APB_BASE + 0x00130000)
+#define QCA955X_OTP_REG_MEM_0 0x0000
+#define QCA955X_OTP_REG_INTF2 0x1008
+#define QCA955X_OTP_REG_STATUS0 0x1018
+#define QCA955X_OTP_STATUS0_EFUSE_VALID BIT(2)
+
+#define QCA955X_OTP_REG_STATUS1 0x101c
+#define QCA955X_OTP_REG_LDO_CTRL 0x1024
+#define QCA955X_OTP_REG_LDO_STATUS 0x102c
+#define QCA955X_OTP_LDO_STATUS_POWER_ON BIT(0)
+
/*
* DDR_CTRL block
*/
@@ -344,6 +355,7 @@
#define QCA955X_RESET_REG_BOOTSTRAP 0xb0
#define QCA955X_RESET_REG_EXT_INT_STATUS 0xac
+#define QCA955X_RESET_REG_RESET_MODULE 0x1c
#define MISC_INT_ETHSW BIT(12)
#define MISC_INT_TIMER4 BIT(10)
@@ -436,6 +448,9 @@
#define AR934X_RESET_MBOX BIT(1)
#define AR934X_RESET_I2S BIT(0)
+#define QCA955X_RESET_SGMII_ANALOG BIT(12)
+#define QCA955X_RESET_SGMII BIT(8)
+
#define AR933X_BOOTSTRAP_MDIO_GPIO_EN BIT(18)
#define AR933X_BOOTSTRAP_EEPBUSY BIT(4)
#define AR933X_BOOTSTRAP_REF_CLK_40 BIT(0)
@@ -722,4 +737,6 @@
#define QCA955X_ETH_CFG_RGMII_GMAC0 BIT(0)
#define QCA955X_ETH_CFG_SGMII_GMAC0 BIT(6)
+#define QCA955X_GMAC_REG_SGMII_SERDES 0x0018
+
#endif /* __ASM_MACH_AR71XX_REGS_H */
diff --git a/target/linux/ath79/image/lzma-loader/src/board.c b/target/linux/ath79/image/lzma-loader/src/board.c
index 2f4dd6b1f6..7b1e110ee2 100644
--- a/target/linux/ath79/image/lzma-loader/src/board.c
+++ b/target/linux/ath79/image/lzma-loader/src/board.c
@@ -10,6 +10,7 @@
#include <stddef.h>
#include "config.h"
+#include "printf.h"
#include "ar71xx_regs.h"
#define READREG(r) *(volatile unsigned int *)(r)
@@ -50,7 +51,139 @@ static void tlwr1043nd_init(void)
static inline void tlwr1043nd_init(void) {}
#endif
+#ifdef CONFIG_BOARD_MERAKI_MR18
+
+static int mr18_extract_sgmii_res_cal(void)
+{
+ unsigned int base;
+ unsigned int reversed_sgmii_value;
+
+ unsigned int otp_value, otp_per_val, rbias_per, read_data;
+ unsigned int rbias_pos_or_neg;
+ unsigned int sgmii_res_cal_value;
+ int res_cal_val;
+
+ base = KSEG1ADDR(QCA955X_OTP_BASE);
+
+ WRITEREG(base + QCA955X_OTP_REG_INTF2, 0x7d);
+ WRITEREG(base + QCA955X_OTP_REG_LDO_CTRL, 0x00);
+
+ while (READREG(base + QCA955X_OTP_REG_LDO_STATUS) &
+ QCA955X_OTP_LDO_STATUS_POWER_ON)
+ ;
+
+ READREG(base + QCA955X_OTP_REG_MEM_0 + 4);
+
+ while (!(READREG(base + QCA955X_OTP_REG_STATUS0) &
+ QCA955X_OTP_STATUS0_EFUSE_VALID))
+ ;
+
+ read_data = READREG(base + QCA955X_OTP_REG_STATUS1);
+
+ if (!(read_data & 0x1fff))
+ return 0;
+
+ if (read_data & 0x00001000)
+ otp_value = (read_data & 0xfc0) >> 6;
+ else
+ otp_value = read_data & 0x3f;
+
+ if (otp_value > 31) {
+ otp_per_val = 63 - otp_value;
+ rbias_pos_or_neg = 1;
+ } else {
+ otp_per_val = otp_value;
+ rbias_pos_or_neg = 0;
+ }
+
+ rbias_per = otp_per_val * 15;
+
+ if (rbias_pos_or_neg == 1)
+ res_cal_val = (rbias_per + 34) / 21;
+ else if (rbias_per > 34)
+ res_cal_val = -((rbias_per - 34) / 21);
+ else
+ res_cal_val = (34 - rbias_per) / 21;
+
+ sgmii_res_cal_value = (8 + res_cal_val) & 0xf;
+
+ reversed_sgmii_value = (sgmii_res_cal_value & 8) >> 3;
+ reversed_sgmii_value |= (sgmii_res_cal_value & 4) >> 1;
+ reversed_sgmii_value |= (sgmii_res_cal_value & 2) << 1;
+ reversed_sgmii_value |= (sgmii_res_cal_value & 1) << 3;
+ printf("SGMII cal value = 0x%x\n", reversed_sgmii_value);
+ return reversed_sgmii_value;
+}
+
+#define QCA955X_SGMII_SERDES_RES_CALIBRATION BIT(23)
+#define QCA955X_SGMII_SERDES_RES_CALIBRATION_MASK 0xf
+#define QCA955X_SGMII_SERDES_RES_CALIBRATION_SHIFT 23
+#define QCA955X_SGMII_SERDES_LOCK_DETECT_STATUS BIT(15)
+#define QCA955X_PLL_ETH_SGMII_SERDES_LOCK_DETECT BIT(2)
+#define QCA955X_PLL_ETH_SGMII_SERDES_PLL_REFCLK BIT(1)
+#define QCA955X_PLL_ETH_SGMII_SERDES_EN_PLL BIT(0)
+#define QCA955X_PLL_CLK_CTRL_REG 0x08
+#define QCA955X_PLL_ETH_XMII_CONTROL_REG 0x28
+#define QCA955X_PLL_ETH_SGMII_CONTROL_REG 0x48
+#define QCA955X_PLL_ETH_SGMII_SERDES_REG 0x4c
+
+static void qca955x_device_reset_clear(unsigned int mask)
+{
+ unsigned int t, reg;
+
+ reg = KSEG1ADDR(AR71XX_RESET_BASE +
+ QCA955X_RESET_REG_RESET_MODULE);
+
+ t = READREG(reg);
+ WRITEREG(reg, t & ~mask);
+}
+
+static void mr18_setup_qca955x_eth_serdes_cal(unsigned int sgmii_value)
+{
+ unsigned int ethbase, pllbase, t;
+
+ ethbase = KSEG1ADDR(QCA955X_GMAC_BASE);
+ pllbase = KSEG1ADDR(AR71XX_PLL_BASE);
+
+ /* To Check the locking of the SGMII PLL */
+ t = READREG(ethbase + QCA955X_GMAC_REG_SGMII_SERDES);
+ t &= ~(QCA955X_SGMII_SERDES_RES_CALIBRATION_MASK <<
+ QCA955X_SGMII_SERDES_RES_CALIBRATION_SHIFT);
+ t |= (sgmii_value & QCA955X_SGMII_SERDES_RES_CALIBRATION_MASK) <<
+ QCA955X_SGMII_SERDES_RES_CALIBRATION_SHIFT;
+ WRITEREG(ethbase + QCA955X_GMAC_REG_SGMII_SERDES, t);
+
+ WRITEREG(pllbase + QCA955X_PLL_ETH_SGMII_SERDES_REG,
+ QCA955X_PLL_ETH_SGMII_SERDES_LOCK_DETECT |
+ QCA955X_PLL_ETH_SGMII_SERDES_PLL_REFCLK |
+ QCA955X_PLL_ETH_SGMII_SERDES_EN_PLL)
+ ;
+
+ qca955x_device_reset_clear(QCA955X_RESET_SGMII_ANALOG);
+ qca955x_device_reset_clear(QCA955X_RESET_SGMII);
+
+ while (!(READREG(ethbase + QCA955X_GMAC_REG_SGMII_SERDES) &
+ QCA955X_SGMII_SERDES_LOCK_DETECT_STATUS))
+ ;
+}
+
+static inline void mr18_init(void)
+{
+ int res;
+
+ printf("Meraki MR18\n");
+
+ res = mr18_extract_sgmii_res_cal();
+ if (res >= 0)
+ mr18_setup_qca955x_eth_serdes_cal(res);
+
+}
+#else
+static inline void mr18_init(void) { }
+#endif
+
void board_init(void)
{
tlwr1043nd_init();
+ mr18_init();
}
diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk
index 10a5485010..4f34521a50 100644
--- a/target/linux/ath79/image/nand.mk
+++ b/target/linux/ath79/image/nand.mk
@@ -11,6 +11,14 @@ define Build/dongwon-header
mv $@.tmp $@
endef
+define Build/meraki-header
+ -$(STAGING_DIR_HOST)/bin/mkmerakifw \
+ -B $(1) -s \
+ -i $@ \
+ -o $@.new
+ @mv $@.new $@
+endef
+
# attention: only zlib compression is allowed for the boot fs
define Build/zyxel-buildkerneljffs
mkdir -p $@.tmp/boot
@@ -260,6 +268,23 @@ define Device/linksys_ea4500-v3
endef
TARGET_DEVICES += linksys_ea4500-v3
+define Device/meraki_mr18
+ SOC := qca9557
+ DEVICE_VENDOR := Meraki
+ DEVICE_MODEL := MR18
+ DEVICE_PACKAGES := kmod-spi-gpio nu801
+ KERNEL_SIZE := 8m
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ LOADER_TYPE := bin
+ KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | meraki-header MR18
+# Initramfs-build fails due to size issues
+# KERNEL_INITRAMFS := $$(KERNEL)
+ KERNEL_INITRAMFS :=
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += meraki_mr18
+
# fake rootfs is mandatory, pad-offset 64 equals (1 * uimage_header)
define Device/netgear_ath79_nand
DEVICE_VENDOR := NETGEAR
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network
index 243c5bb7aa..60f085d378 100644
--- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
@@ -8,7 +8,8 @@ ath79_setup_interfaces()
case "$board" in
aerohive,hiveap-121|\
- glinet,gl-e750)
+ glinet,gl-e750|\
+ meraki,mr18)
ucidef_set_interface_lan "eth0"
;;
domywifi,dw33d)
@@ -102,6 +103,9 @@ ath79_setup_macs()
wan_mac=$(mtd_get_mac_binary art 0x0)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
+ meraki,mr18)
+ lan_mac=$(mtd_get_mac_binary_ubi board-config 102)
+ ;;
netgear,wndr3700-v4|\
netgear,wndr4300|\
netgear,wndr4300sw|\
diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 36ab24e2df..c4ccb04f5b 100644
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -12,6 +12,50 @@ case "$FIRMWARE" in
8dev,rambutan)
caldata_extract "caldata" 0x1000 0x800
;;
+ meraki,mr18)
+ . /lib/upgrade/nand.sh
+
+ if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+ caldata_extract_ubi "caldata" 0x1000 0x440
+ else
+ caldata_extract "odm-caldata" 0x1000 0x440
+ fi
+ ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) 1)
+ ;;
+ *)
+ caldata_die "board $board is not supported yet"
+ ;;
+ esac
+ ;;
+"ath9k-eeprom-pci-0000:00:00.0.bin")
+ case $board in
+ meraki,mr18)
+ . /lib/upgrade/nand.sh
+
+ if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+ caldata_extract_ubi "caldata" 0x5000 0x440
+ else
+ caldata_extract "odm-caldata" 0x5000 0x440
+ fi
+ ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) 2)
+ ;;
+ *)
+ caldata_die "board $board is not supported yet"
+ ;;
+ esac
+ ;;
+"ath9k-eeprom-pci-0000:01:00.0.bin")
+ case $board in
+ meraki,mr18)
+ . /lib/upgrade/nand.sh
+
+ if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+ caldata_extract_ubi "caldata" 0x9000 0x440
+ else
+ caldata_extract "odm-caldata" 0x9000 0x440
+ fi
+ ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) 3)
+ ;;
*)
caldata_die "board $board is not supported yet"
;;