diff options
| author | Piotr Dymacz <pepe2k@gmail.com> | 2021-09-17 14:52:04 +0200 |
|---|---|---|
| committer | Piotr Dymacz <pepe2k@gmail.com> | 2021-11-03 12:45:40 +0100 |
| commit | 5dfa89be9900819a2796f3ff9c3f395735035f3c (patch) | |
| tree | a0ecd88aa53a3ee2d002c1792dde019bfbc86718 /target/linux/ath79/nand | |
| parent | 20d3e236b2a85e22ffeb9da7cbc699d6103ca212 (diff) | |
| download | upstream-5dfa89be9900819a2796f3ff9c3f395735035f3c.tar.gz upstream-5dfa89be9900819a2796f3ff9c3f395735035f3c.tar.bz2 upstream-5dfa89be9900819a2796f3ff9c3f395735035f3c.zip | |
ath79: add support for Netgear R6100
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.
Specifications:
- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)
WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.
Installation:
Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ath79/nand')
3 files changed, 11 insertions, 0 deletions
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/01_leds b/target/linux/ath79/nand/base-files/etc/board.d/01_leds index f694d07e9c..dc7d84df95 100644 --- a/target/linux/ath79/nand/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/nand/base-files/etc/board.d/01_leds @@ -14,6 +14,9 @@ glinet,gl-ar300m-nand|\ glinet,gl-ar300m-nor) ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" ;; +netgear,r6100) + ucidef_set_led_netdev "wan-green" "WAN (green)" "green:wan" "eth1" + ;; netgear,wndr3700-v4|\ netgear,wndr4300|\ netgear,wndr4300sw|\ diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network index dbb9e68150..76cdab18f8 100644 --- a/target/linux/ath79/nand/base-files/etc/board.d/02_network +++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network @@ -25,6 +25,11 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "2:lan:2" "3:lan:1" "1:wan" ;; + netgear,r6100) + ucidef_set_interface_wan "eth1" + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3" + ;; netgear,wndr3700-v4|\ netgear,wndr4300|\ netgear,wndr4300sw|\ diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 71dfb161e4..03e225ddde 100644 --- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -23,6 +23,9 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) 1) ;; + netgear,r6100) + caldata_extract "caldata" 0x5000 0x844 + ;; zyxel,nbg6716) caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 1) |