diff options
| author | Sander Vanheule <sander@svanheule.net> | 2020-07-26 22:40:54 +0200 |
|---|---|---|
| committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-09-12 19:37:24 +0200 |
| commit | c9f51a9ad6e8f99ed7adb78d208740b7d351985b (patch) | |
| tree | 2ac82f84c562304068d1345b16fca19dd468bde4 /target/linux/ath79/image | |
| parent | 53df30f02beab977991431c6f687f5ac5d88999c (diff) | |
| download | upstream-c9f51a9ad6e8f99ed7adb78d208740b7d351985b.tar.gz upstream-c9f51a9ad6e8f99ed7adb78d208740b7d351985b.tar.bz2 upstream-c9f51a9ad6e8f99ed7adb78d208740b7d351985b.zip | |
ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/ath79/image')
| -rw-r--r-- | target/linux/ath79/image/generic-tp-link.mk | 13 |
1 files changed, 12 insertions, 1 deletions
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index daf793671f..22d1ac8a9e 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -364,7 +364,6 @@ TARGET_DEVICES += tplink_cpe610-v2 define Device/tplink-eap2x5 $(Device/tplink-safeloader) - SOC := qca9563 LOADER_TYPE := elf KERNEL := kernel-bin | append-dtb | lzma | loader-kernel KERNEL_INITRAMFS := $$(KERNEL) @@ -372,8 +371,20 @@ define Device/tplink-eap2x5 pad-extra 128 endef +define Device/tplink_eap225-wall-v2 + $(Device/tplink-eap2x5) + SOC := qca9561 + IMAGE_SIZE := 13824k + DEVICE_MODEL := EAP225-Wall + DEVICE_VARIANT := v2 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := EAP225-WALL-V2 +endef +TARGET_DEVICES += tplink_eap225-wall-v2 + define Device/tplink_eap245-v3 $(Device/tplink-eap2x5) + SOC := qca9563 IMAGE_SIZE := 14592k DEVICE_MODEL := EAP245 DEVICE_VARIANT := v3 |