diff options
| author | Paul Maruhn <paulmaruhn@posteo.de> | 2022-03-22 21:06:42 +0100 |
|---|---|---|
| committer | Sander Vanheule <sander@svanheule.net> | 2022-06-22 17:47:11 +0200 |
| commit | 7e4de89e631aaf56be5375662b7d5ed0f27e26f6 (patch) | |
| tree | 1a70fe34a823bc6e415148edb52bb03760564a49 /target/linux/ath79/generic | |
| parent | 8bd5bbad1ea8376f619d61ba36963bab9f4d3361 (diff) | |
| download | upstream-7e4de89e631aaf56be5375662b7d5ed0f27e26f6.tar.gz upstream-7e4de89e631aaf56be5375662b7d5ed0f27e26f6.tar.bz2 upstream-7e4de89e631aaf56be5375662b7d5ed0f27e26f6.zip | |
ath79: support for TP-Link EAP225-Outdoor v3
This model is almost identical to the EAP225-Outdoor v1.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de>
Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de>
Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
[Add pre-calibraton nvme-cells]
Tested-by: Tido Klaassen <tido_ff@4gh.eu>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Diffstat (limited to 'target/linux/ath79/generic')
| -rw-r--r-- | target/linux/ath79/generic/base-files/etc/board.d/02_network | 1 |
1 files changed, 1 insertions, 0 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index d4e956c406..209395f024 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -76,6 +76,7 @@ ath79_setup_interfaces() tplink,cpe610-v2|\ tplink,cpe710-v1|\ tplink,eap225-outdoor-v1|\ + tplink,eap225-outdoor-v3|\ tplink,eap225-v1|\ tplink,eap225-v3|\ tplink,eap245-v1|\ |