diff options
| author | Joe Mullally <jwmullally@gmail.com> | 2021-08-30 22:35:05 +0100 |
|---|---|---|
| committer | Hauke Mehrtens <hauke@hauke-m.de> | 2022-04-09 19:31:46 +0200 |
| commit | 44e1e5d153d00915a7e516c9af3f440cbd84cf78 (patch) | |
| tree | a35a129382631bc3d0cc431ca96c10befd75834d /target/linux/ath79/generic | |
| parent | 6461384c1e3515e38f9ab62fef2ffaabb840da42 (diff) | |
| download | upstream-44e1e5d153d00915a7e516c9af3f440cbd84cf78.tar.gz upstream-44e1e5d153d00915a7e516c9af3f440cbd84cf78.tar.bz2 upstream-44e1e5d153d00915a7e516c9af3f440cbd84cf78.zip | |
ath79: Move TPLink WPA8630Pv2 to ath79-tiny target
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.
Note for users sysupgrading from the previous ath79-generic snapshot
images:
The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.
To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".
If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:
* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
Diffstat (limited to 'target/linux/ath79/generic')
3 files changed, 3 insertions, 12 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 2ce489b0d1..e22cee51a3 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -401,10 +401,7 @@ tplink,tl-mr6400-v1) ucidef_set_led_netdev "wan" "WAN" "white:wan" "eth1" ucidef_set_led_netdev "4g" "4G" "white:4g" "usb0" ;; -tplink,tl-wpa8630-v1|\ -tplink,tl-wpa8630p-v2-int|\ -tplink,tl-wpa8630p-v2.0-eu|\ -tplink,tl-wpa8630p-v2.1-eu) +tplink,tl-wpa8630-v1) ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3c" ;; tplink,tl-wr841hp-v2|\ diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index bc32081910..2f0208b288 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -440,10 +440,7 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:1" "2:lan:3" "3:lan:2" ;; - tplink,tl-wpa8630-v1|\ - tplink,tl-wpa8630p-v2-int|\ - tplink,tl-wpa8630p-v2.0-eu|\ - tplink,tl-wpa8630p-v2.1-eu) + tplink,tl-wpa8630-v1) # port 5 (internal) is the power-line port ucidef_add_switch "switch0" \ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4" diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index b8e99a661f..348b8839b6 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -249,10 +249,7 @@ case "$FIRMWARE" in ;; tplink,eap225-outdoor-v1|\ tplink,eap225-v3|\ - tplink,eap225-wall-v2|\ - tplink,tl-wpa8630p-v2-int|\ - tplink,tl-wpa8630p-v2.0-eu|\ - tplink,tl-wpa8630p-v2.1-eu) + tplink,eap225-wall-v2) caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) 1) ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ |