diff options
| author | Sander Vanheule <sander@svanheule.net> | 2020-07-10 13:41:21 +0200 |
|---|---|---|
| committer | Petr Štetiar <ynezz@true.cz> | 2020-11-23 22:53:15 +0100 |
| commit | b0ecae504b58bf65627138fe14eb605ad77224c9 (patch) | |
| tree | 8ebcf8ff600137a140aa184f7fa962bd380add5b /target/linux/ath79/generic/base-files | |
| parent | 4f86edf477edbc0f20b5a49a69f658fa82158284 (diff) | |
| download | upstream-b0ecae504b58bf65627138fe14eb605ad77224c9.tar.gz upstream-b0ecae504b58bf65627138fe14eb605ad77224c9.tar.bz2 upstream-b0ecae504b58bf65627138fe14eb605ad77224c9.zip | |
ath79: support for TP-Link EAP225 v3
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:
Using interface ath0 with hwaddr b0:...:3e and ssid "..."
Using interface ath10 with hwaddr b0:...:3f and ssid "..."
Tested by forum user blinkstar88
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Diffstat (limited to 'target/linux/ath79/generic/base-files')
| -rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/02_network | 1 | ||||
| -rw-r--r-- | target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 1 |
2 files changed, 2 insertions, 0 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 928b6c8903..5fbf4e2561 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -49,6 +49,7 @@ ath79_setup_interfaces() tplink,cpe610-v1|\ tplink,cpe610-v2|\ tplink,eap225-outdoor-v1|\ + tplink,eap225-v3|\ tplink,eap245-v1|\ tplink,re350k-v1|\ tplink,re355-v1|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 5be1c72ab0..ff15414ead 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -209,6 +209,7 @@ case "$FIRMWARE" in /lib/firmware/ath10k/QCA9888/hw2.0/board.bin ;; tplink,eap225-outdoor-v1|\ + tplink,eap225-v3|\ tplink,eap225-wall-v2|\ tplink,tl-wpa8630p-v2-int|\ tplink,tl-wpa8630p-v2.0-eu|\ |