diff options
| author | Joe Mullally <jwmullally@gmail.com> | 2021-08-30 22:35:05 +0100 |
|---|---|---|
| committer | Petr Štetiar <ynezz@true.cz> | 2022-04-16 14:59:34 +0200 |
| commit | 1d4dea6d4f4d34914e4622809b8b4a7c2c35ab47 (patch) | |
| tree | 66e0b5f87e3424d1f066a7392f3fb05d5127e191 /target/linux/ath79/generic/base-files | |
| parent | 41a97c207438903c309371ba695cea01ae78aba4 (diff) | |
| download | upstream-1d4dea6d4f4d34914e4622809b8b4a7c2c35ab47.tar.gz upstream-1d4dea6d4f4d34914e4622809b8b4a7c2c35ab47.tar.bz2 upstream-1d4dea6d4f4d34914e4622809b8b4a7c2c35ab47.zip | |
ath79: Move TPLink WPA8630Pv2 to ath79-tiny target
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.
Note for users sysupgrading from the previous ath79-generic snapshot
images:
The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.
To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".
If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:
* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message facelift]
(cherry picked from commit 44e1e5d)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Diffstat (limited to 'target/linux/ath79/generic/base-files')
3 files changed, 3 insertions, 12 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index b6c68db813..146470855d 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -348,10 +348,7 @@ tplink,tl-mr6400-v1) ucidef_set_led_netdev "wan" "WAN" "white:wan" "eth1" ucidef_set_led_netdev "4g" "4G" "white:4g" "usb0" ;; -tplink,tl-wpa8630-v1|\ -tplink,tl-wpa8630p-v2-int|\ -tplink,tl-wpa8630p-v2.0-eu|\ -tplink,tl-wpa8630p-v2.1-eu) +tplink,tl-wpa8630-v1) ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3c" ;; tplink,tl-wr842n-v2) diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 5bf78117e1..b01dfa41d1 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -382,10 +382,7 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:1" "2:lan:3" "3:lan:2" ;; - tplink,tl-wpa8630-v1|\ - tplink,tl-wpa8630p-v2-int|\ - tplink,tl-wpa8630p-v2.0-eu|\ - tplink,tl-wpa8630p-v2.1-eu) + tplink,tl-wpa8630-v1) # port 5 (internal) is the power-line port ucidef_add_switch "switch0" \ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4" diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index c562fa7c74..c7dbaafac1 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -228,10 +228,7 @@ case "$FIRMWARE" in ;; tplink,eap225-outdoor-v1|\ tplink,eap225-v3|\ - tplink,eap225-wall-v2|\ - tplink,tl-wpa8630p-v2-int|\ - tplink,tl-wpa8630p-v2.0-eu|\ - tplink,tl-wpa8630p-v2.1-eu) + tplink,eap225-wall-v2) caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1) ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ |