aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/generic/base-files
diff options
context:
space:
mode:
authorSander Vanheule <sander@svanheule.net>2020-07-10 13:41:21 +0200
committerPetr Štetiar <ynezz@true.cz>2020-11-23 22:53:15 +0100
commitb0ecae504b58bf65627138fe14eb605ad77224c9 (patch)
tree8ebcf8ff600137a140aa184f7fa962bd380add5b /target/linux/ath79/generic/base-files
parent4f86edf477edbc0f20b5a49a69f658fa82158284 (diff)
downloadupstream-b0ecae504b58bf65627138fe14eb605ad77224c9.tar.gz
upstream-b0ecae504b58bf65627138fe14eb605ad77224c9.tar.bz2
upstream-b0ecae504b58bf65627138fe14eb605ad77224c9.zip
ath79: support for TP-Link EAP225 v3
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access point. Serial port access for debricking requires fine soldering. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From OEM boot log: Using interface ath0 with hwaddr b0:...:3e and ssid "..." Using interface ath10 with hwaddr b0:...:3f and ssid "..." Tested by forum user blinkstar88 Signed-off-by: Sander Vanheule <sander@svanheule.net>
Diffstat (limited to 'target/linux/ath79/generic/base-files')
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata1
2 files changed, 2 insertions, 0 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 928b6c8903..5fbf4e2561 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -49,6 +49,7 @@ ath79_setup_interfaces()
tplink,cpe610-v1|\
tplink,cpe610-v2|\
tplink,eap225-outdoor-v1|\
+ tplink,eap225-v3|\
tplink,eap245-v1|\
tplink,re350k-v1|\
tplink,re355-v1|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 5be1c72ab0..ff15414ead 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -209,6 +209,7 @@ case "$FIRMWARE" in
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
tplink,eap225-outdoor-v1|\
+ tplink,eap225-v3|\
tplink,eap225-wall-v2|\
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\