ath79: refactor ZTE MF28x dts files

Move common dts entries of ZTE MF281 and ZTE MF286 to a common .dtsi file
to reduce redundancies.

Signed-off-by: Andreas Böhler <dev@aboehler.at>

3 files changed, 233 insertions, 329 deletions

diff --git a/target/linux/ath79/dts/qca9563_zte_mf281.dts b/target/linux/ath79/dts/qca9563_zte_mf281.dts
index 2f4b7316bf..9205061e24 100644
--- a/target/linux/ath79/dts/qca9563_zte_mf281.dts
+++ b/target/linux/ath79/dts/qca9563_zte_mf281.dts
@@ -3,246 +3,157 @@
 // Copyright (c) 2021, 2022 Lech Perczak
 // Copyright (c) 2022 David Bauer <mail@david-bauer.net>
 
-#include "qca956x.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
+#include "qca9563_zte_mf28x.dtsi"
 
 / {
 	model = "ZTE MF281";
 	compatible = "zte,mf281", "qca,qca9563";
 
-	aliases {
-		led-boot = &led_debug;
-		led-failsafe = &led_debug;
-		led-running = &led_debug;
-		led-upgrade = &led_debug;
-		label-mac-device = &eth0;
-	};
-
 	leds {
-		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&enable_wlan_led_gpio>;
-
-		/* Hidden SMD LED below signal strength LEDs.
-		 * Visible through slits underside of the case.
-		 */
-		led_debug: debug {
-			label = "green:debug";
-			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
-			default-state = "on";
-		};
 	};
+};
 
-	keys {
-		compatible = "gpio-keys";
+&led_debug {
+	label = "green:debug";
+	color = <LED_COLOR_ID_GREEN>;
+};
 
-		reset {
-			label = "reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
+&boot_flash {
+	partitions {
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0xa0000>;
+			read-only;
 		};
 
-		wps {
-			label = "wps";
-			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
+		partition@80000 {
+			label = "u-boot-env";
+			reg = <0xa0000 0x20000>;
+			read-only;
 		};
 	};
-
-	/* This GPIO is used to reset whole board _including_ the modem */
-	gpio-restart {
-		compatible = "gpio-restart";
-		gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
-		active-delay = <3000>;
-		inactive-delay = <1000>;
-	};
 };
 
-&spi {
-	status = "okay";
+&system_flash {
+	partitions {
+		partition@0 {
+			label = "fota-flag";
+			reg = <0x000000 0xa0000>;
+			read-only;
+		};
 
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <25000000>;
+		partition@a0000 {
+			label = "art";
+			reg = <0xa0000 0x80000>;
+			read-only;
 
-		partitions {
-			compatible = "fixed-partitions";
+			compatible = "nvmem-cells";
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			partition@0 {
-				label = "u-boot";
-				reg = <0x0 0xa0000>;
-				read-only;
+			cal_caldata_1000: cal@1000 {
+				reg = <0x1000 0x440>;
 			};
 
-			partition@80000 {
-				label = "u-boot-env";
-				reg = <0xa0000 0x20000>;
-				read-only;
+			cal_caldata_5000: cal@5000 {
+				reg = <0x5000 0x2f20>;
 			};
 		};
-	};
 
-	flash@1 {
-		compatible = "spi-nand";
-		reg = <1>;
-		spi-max-frequency = <25000000>;
+		partition@120000 {
+			label = "mac";
+			reg = <0x120000 0x80000>;
+			read-only;
 
-		partitions {
-			compatible = "fixed-partitions";
+			compatible = "nvmem-cells";
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			partition@0 {
-				label = "fota-flag";
-				reg = <0x000000 0xa0000>;
-				read-only;
-			};
-
-			partition@a0000 {
-				label = "art";
-				reg = <0xa0000 0x80000>;
-				read-only;
-
-				compatible = "nvmem-cells";
-				#address-cells = <1>;
-				#size-cells = <1>;
-
-				cal_caldata_1000: cal@1000 {
-					reg = <0x1000 0x440>;
-				};
-
-				cal_caldata_5000: cal@5000 {
-					reg = <0x5000 0x2f20>;
-				};
-			};
-
-			partition@120000 {
-				label = "mac";
-				reg = <0x120000 0x80000>;
-				read-only;
-
-				compatible = "nvmem-cells";
-				#address-cells = <1>;
-				#size-cells = <1>;
-
-				macaddr_mac_0: macaddr@0 {
-					reg = <0x0 0x6>;
-				};
-			};
-
-			partition@1a0000 {
-				label = "reserved2";
-				reg = <0x1a0000 0xc0000>;
-				read-only;
-			};
-
-			partition@260000 {
-				label = "cfg-param";
-				reg = <0x260000 0x400000>;
-				read-only;
+			macaddr_mac_0: macaddr@0 {
+				reg = <0x0 0x6>;
 			};
+		};
 
-			partition@660000 {
-				label = "log";
-				reg = <0x660000 0x400000>;
-				read-only;
-			};
+		partition@1a0000 {
+			label = "reserved2";
+			reg = <0x1a0000 0xc0000>;
+			read-only;
+		};
 
-			partition@a60000 {
-				label = "oops";
-				reg = <0xa60000 0xa0000>;
-				read-only;
-			};
+		partition@260000 {
+			label = "cfg-param";
+			reg = <0x260000 0x400000>;
+			read-only;
+		};
 
-			partition@b00000 {
-				label = "reserved3";
-				reg = <0xb00000 0x500000>;
-				read-only;
-			};
+		partition@660000 {
+			label = "log";
+			reg = <0x660000 0x400000>;
+			read-only;
+		};
 
-			partition@1000000 {
-				label = "web";
-				reg = <0x1000000 0x800000>;
-				read-only;
-			};
+		partition@a60000 {
+			label = "oops";
+			reg = <0xa60000 0xa0000>;
+			read-only;
+		};
 
-			partition@1800000 {
-				label = "firmware";
-				reg = <0x1800000 0x1d00000>;
+		partition@b00000 {
+			label = "reserved3";
+			reg = <0xb00000 0x500000>;
+			read-only;
+		};
 
-				compatible = "fixed-partitions";
-				#address-cells = <1>;
-				#size-cells = <1>;
+		partition@1000000 {
+			label = "web";
+			reg = <0x1000000 0x800000>;
+			read-only;
+		};
 
-				partition@0 {
-					label = "kernel";
-					reg = <0x0 0x600000>;
-				};
+		partition@1800000 {
+			label = "firmware";
+			reg = <0x1800000 0x1d00000>;
 
-				partition@600000 {
-					label = "ubi";
-					reg = <0x600000 0x1700000>;
-				};
-			};
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-			partition@3500000 {
-				label = "data";
-				reg = <0x3500000 0x1900000>;
-				read-only;
+			partition@0 {
+				label = "kernel";
+				reg = <0x0 0x600000>;
 			};
 
-			partition@4e00000 {
-				label = "fota";
-				reg = <0x4e00000 0x3200000>;
-				read-only;
+			partition@600000 {
+				label = "ubi";
+				reg = <0x600000 0x1700000>;
 			};
 		};
-	};
-};
 
-&mdio0 {
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		phy-mode = "sgmii";
+		partition@3500000 {
+			label = "data";
+			reg = <0x3500000 0x1900000>;
+			read-only;
+		};
 
-		qca,ar8327-initvals = <
-			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
-			0x7c 0x0000007e /* PORT0_STATUS */
-		>;
+		partition@4e00000 {
+			label = "fota";
+			reg = <0x4e00000 0x3200000>;
+			read-only;
+		};
 	};
 };
 
 &eth0 {
-	status = "okay";
-
-	phy-mode = "sgmii";
-	phy-handle = <&phy0>;
-
 	nvmem-cells = <&macaddr_mac_0>;
 	nvmem-cell-names = "mac-address";
 };
 
-&pcie {
-	status = "okay";
-
-	wifi@0,0 {
-		compatible = "qcom,ath10k";
-		reg = <0x0 0 0 0 0>;
-
-		nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_5000>;
-		nvmem-cell-names = "mac-address", "pre-calibration";
-		mac-address-increment = <1>;
-	};
+&wifi_ath10k {
+	nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_5000>;
+	nvmem-cell-names = "mac-address", "pre-calibration";
+	mac-address-increment = <1>;
 };
 
 &pinmux {
@@ -252,24 +163,6 @@
 };
 
 &wmac {
-	status = "okay";
-
 	nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_1000>;
 	nvmem-cell-names = "mac-address", "calibration";
 };
-
-&usb_phy0 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&usb_phy1 {
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
diff --git a/target/linux/ath79/dts/qca9563_zte_mf286.dtsi b/target/linux/ath79/dts/qca9563_zte_mf286.dtsi
index f794195c3f..df9a9d3f69 100644
--- a/target/linux/ath79/dts/qca9563_zte_mf286.dtsi
+++ b/target/linux/ath79/dts/qca9563_zte_mf286.dtsi
@@ -1,36 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 // Copyright (c) 2021 Cezary Jackiewicz
 // Copyright (c) 2021, 2022 Lech Perczak
-#include "qca956x.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
+#include "qca9563_zte_mf28x.dtsi"
 
 / {
-	aliases {
-		led-boot = &led_debug;
-		led-failsafe = &led_debug;
-		led-running = &led_debug;
-		led-upgrade = &led_debug;
-		label-mac-device = &eth0;
-	};
-
 	leds {
-		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&enable_wlan_led_gpio>;
 
-		/* Hidden SMD LED below signal strength LEDs.
-		 * Visible through slits underside of the case,
-		 * and slightly through the case below signal state LEDs
-		 */
-		led_debug: led-0 {
-			function = LED_FUNCTION_DEBUG;
-			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
-			default-state = "on";
-		};
-
 		led-1 {
 			function = LED_FUNCTION_WLAN;
 			color = <LED_COLOR_ID_BLUE>;
@@ -40,22 +17,6 @@
 	};
 
 	keys {
-		compatible = "gpio-keys";
-
-		reset {
-			label = "reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
-
-		wps {
-			label = "wps";
-			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
-
 		wifi {
 			label = "wifi";
 			linux,code = <KEY_RFKILL>;
@@ -63,72 +24,6 @@
 			debounce-interval = <60>;
 		};
 	};
-
-	/* This GPIO is used to reset whole board _including_ the modem */
-	gpio-restart {
-		compatible = "gpio-restart";
-		gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
-		active-delay = <3000>;
-		inactive-delay = <1000>;
-	};
-};
-
-&spi {
-	status = "okay";
-
-	boot_flash: flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <25000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-		};
-	};
-
-	system_flash: flash@1 {
-		compatible = "spi-nand";
-		reg = <1>;
-		spi-max-frequency = <25000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-		};
-	};
-};
-
-&mdio0 {
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		phy-mode = "sgmii";
-
-		qca,ar8327-initvals = <
-			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
-			0x7c 0x0000007e /* PORT0_STATUS */
-		>;
-	};
-};
-
-&eth0 {
-	status = "okay";
-
-	phy-mode = "sgmii";
-	phy-handle = <&phy0>;
-};
-
-&pcie {
-	status = "okay";
-
-	wifi_ath10k: wifi@0,0 {
-		compatible = "qcom,ath10k";
-		reg = <0x0 0 0 0 0>;
-	};
 };
 
 &pinmux {
@@ -136,23 +31,3 @@
 		pinctrl-single,bits = <0x10 0x0 0xff000000>;
 	};
 };
-
-&wmac {
-	status = "okay";
-};
-
-&usb_phy0 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&usb_phy1 {
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
diff --git a/target/linux/ath79/dts/qca9563_zte_mf28x.dtsi b/target/linux/ath79/dts/qca9563_zte_mf28x.dtsi
new file mode 100644
index 0000000000..1edcd7e5ea
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_zte_mf28x.dtsi
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2021 Cezary Jackiewicz
+// Copyright (c) 2021, 2022 Lech Perczak
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		led-boot = &led_debug;
+		led-failsafe = &led_debug;
+		led-running = &led_debug;
+		led-upgrade = &led_debug;
+		label-mac-device = &eth0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* Hidden SMD LED below signal strength LEDs.
+		 * Visible through slits underside of the case,
+		 * and slightly through the case below signal state LEDs
+		 */
+		led_debug: led-0 {
+			function = LED_FUNCTION_DEBUG;
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	/* This GPIO is used to reset whole board _including_ the modem */
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+		active-delay = <3000>;
+		inactive-delay = <1000>;
+	};
+};
+
+&spi {
+	status = "okay";
+
+	boot_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+
+	system_flash: flash@1 {
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		phy-mode = "sgmii";
+
+		qca,ar8327-initvals = <
+			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+			0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+};
+
+&pcie {
+	status = "okay";
+
+	wifi_ath10k: wifi@0,0 {
+		compatible = "qcom,ath10k";
+		reg = <0x0 0 0 0 0>;
+	};
+};
+
+&wmac {
+	status = "okay";
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};