ath79: Add support for OpenMesh OM5P

Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here.

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[add LED swap comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

1 files changed, 166 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/ar9344_openmesh_om5p.dts b/target/linux/ath79/dts/ar9344_openmesh_om5p.dts
new file mode 100644
index 0000000000..a733a922e4
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_openmesh_om5p.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "openmesh,om5p", "qca,ar9344";
+	model = "OpenMesh OM5P";
+
+	chosen {
+		/delete-property/ bootargs;
+	};
+
+	aliases {
+		serial0 = &uart;
+		led-boot = &led_power_blue;
+		led-failsafe = &led_power_blue;
+		led-running = &led_power_blue;
+		led-upgrade = &led_power_blue;
+		label-mac-device = &eth1;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_lan_wan_blue_pin>;
+
+		led_power_blue: power_blue {
+			label = "blue:power";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wan_blue {
+			label = "blue:wan";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		lan_blue {
+			label = "blue:lan";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi_green {
+			label = "green:wifi";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wifi_yellow {
+			label = "yellow:wifi";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi_red {
+			label = "red:wifi";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	watchdog {
+		compatible = "linux,wdt-gpio";
+		gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		hw_algo = "toggle";
+		/* hw_margin_ms is actually 300s but driver limits it to 60s */
+		hw_margin_ms = <60000>;
+		always-running;
+	};
+};
+
+&ref {
+	clock-frequency = <40000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&pinmux {
+	led_lan_wan_blue_pin: pinmux_lan_wan_blue_pin {
+		pinctrl-single,bits = <0xc 0x0 0xffff0000>;
+	};
+};
+
+&spi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		/* partitions are passed via bootloader */
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@50000 {
+				label = "custom";
+				reg = <0x050000 0x060000>;
+				read-only;
+			};
+
+			partition@b0000 {
+				label = "inactive";
+				reg = <0x0b0000 0x7a0000>;
+			};
+
+			partition@850000 {
+				label = "inactive2";
+				reg = <0x850000 0x7a0000>;
+			};
+
+			art: partition@ff0000 {
+				label = "ART";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&swphy4>;
+
+	mtd-mac-address = <&art 0x6>;
+};
+
+&eth1 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x0>;
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};