ath79: add support for NEC Aterm WG800HP

NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>

1 files changed, 188 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/qca9563_nec_wg800hp.dts b/target/linux/ath79/dts/qca9563_nec_wg800hp.dts
new file mode 100644
index 0000000000..9cba99b6a6
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_nec_wg800hp.dts
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	model = "NEC Aterm WG800HP";
+	compatible = "nec,wg800hp", "qca,qca9563";
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-boot = &power_green;
+		led-failsafe = &power_red;
+		led-running = &power_green;
+		led-upgrade = &power_green;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&jtag_disable_pins>;
+
+		wlan2g_red {
+			label = "wg800hp:red:wlan2g";
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+		};
+
+		active_red {
+			label = "wg800hp:red:active";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		active_green {
+			label = "wg800hp:green:active";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		power_red: power_red {
+			label = "wg800hp:red:power";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		power_green: power_green {
+			label = "wg800hp:green:power";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wlan5g_red {
+			label = "wg800hp:red:wlan5g";
+			gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g_green {
+			label = "wg800hp:green:wlan5g";
+			gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan2g_green {
+			label = "wg800hp:green:wlan2g";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		br {
+			label = "br";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+			debounce-interval = <60>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+				read-only;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0x6f0000>;
+			};
+
+			partition@740000 {
+				label = "user_data";
+				reg = <0x740000 0x0a0000>;
+				read-only;
+			};
+
+			partition@7e0000 {
+				label = "board_data";
+				reg = <0x7e0000 0x010000>;
+				read-only;
+			};
+
+			art: partition@7f0000 {
+				label = "art";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+
+		qca,ar8327-initvals = <
+			0x04 0x00000080 /* PORT0 PAD MODE CTRL */
+			0x50 0xcc35cc35 /* LED_CTRL0 */
+			0x54 0xca35ca35 /* LED_CTRL1 */
+			0x58 0xc935c935 /* LED_CTRL2 */
+			0x5c 0x03ffff00 /* LED_CTRL3 */
+			0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&wmac {
+	status = "okay";
+	qca,no-eeprom;
+};