diff options
author | Piotr Dymacz <pepe2k@gmail.com> | 2020-03-21 23:20:31 +0100 |
---|---|---|
committer | Piotr Dymacz <pepe2k@gmail.com> | 2020-09-28 01:28:37 +0200 |
commit | 66abd58196a8e1195f1e2cd9871b4fc194b6570b (patch) | |
tree | d0959571e260cfdd3083fd4f8d1ba132379d270a /target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts | |
parent | 7f96cbd2a11a382a940ecdfc75d45bad44283414 (diff) | |
download | upstream-66abd58196a8e1195f1e2cd9871b4fc194b6570b.tar.gz upstream-66abd58196a8e1195f1e2cd9871b4fc194b6570b.tar.bz2 upstream-66abd58196a8e1195f1e2cd9871b4fc194b6570b.zip |
ath79: add support for ALFA Network AP121FE
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts')
-rw-r--r-- | target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts | 104 |
1 files changed, 1 insertions, 103 deletions
diff --git a/target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts b/target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts index 286b6d1be2..bfb6d3152c 100644 --- a/target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts +++ b/target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts @@ -1,38 +1,11 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "ar9331.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> +#include "ar9331_alfa-network_ap121f.dtsi" / { model = "ALFA Network AP121F"; compatible = "alfa-network,ap121f", "qca,ar9331"; - aliases { - label-mac-device = &wmac; - led-boot = &led_vpn; - led-failsafe = &led_vpn; - led-upgrade = &led_vpn; - serial0 = &uart; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - linux,code = <KEY_RESTART>; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - - switch { - label = "switch"; - linux,code = <BTN_0>; - gpios = <&gpio 21 GPIO_ACTIVE_HIGH>; - }; - }; - leds { compatible = "gpio-leds"; @@ -54,81 +27,6 @@ }; }; -ð0 { - status = "okay"; - - mtd-mac-address = <&art 0x0>; - - gmac-config { - device = <&gmac>; - switch-phy-addr-swap = <0>; - switch-phy-swap = <0>; - }; -}; - -ð1 { - status = "okay"; - - compatible = "syscon", "simple-mfd"; -}; - -&spi { - status = "okay"; - - num-cs = <1>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <50000000>; - m25p,fast-read; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x000000 0x030000>; - read-only; - }; - - partition@30000 { - label = "u-boot-env"; - reg = <0x030000 0x010000>; - }; - - art: partition@40000 { - label = "art"; - reg = <0x040000 0x010000>; - read-only; - }; - - partition@50000 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x050000 0xfb0000>; - }; - }; - }; -}; - -&uart { - status = "okay"; -}; - &usb { - status = "okay"; dr_mode = "host"; }; - -&usb_phy { - status = "okay"; -}; - -&wmac { - status = "okay"; - - mtd-cal-data = <&art 0x1000>; -}; |