ath79: fix PQI Air Pen support

Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>.

Signed-off-by: Mathias Kresin <dev@kresin.me>

1 files changed, 147 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/ar9330_pqi_air-pen.dts b/target/linux/ath79/dts/ar9330_pqi_air-pen.dts
new file mode 100644
index 0000000000..6c662d2202
--- /dev/null
+++ b/target/linux/ath79/dts/ar9330_pqi_air-pen.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9330.dtsi"
+
+/ {
+	model = "PQI Air-Pen";
+	compatible = "pqi,air-pen", "qca,ar9330";
+
+	aliases {
+		serial0 = &uart;
+		led-boot = &wlan;
+		led-failsafe = &wlan;
+		led-upgrade = &wlan;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan: wlan {
+			label = "air-pen:blue:wlan";
+			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wps {
+			label = "air-pen:blue:wps";
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			debounce-interval = <60>;
+		};
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	num-cs = <1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			art: partition@50000 {
+				label = "art";
+				reg = <0x050000 0x010000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "NVRAM";
+				reg = <0x060000 0x010000>;
+				read-only;
+			};
+
+			partition@70000 {
+				label = "firmware";
+				reg = <0x070000 0x780000>;
+			};
+
+			partition@7f0000 {
+				label = "CONF";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x1002>;
+
+	gmac-config {
+		device = <&gmac>;
+
+		switch-phy-addr-swap = <0>;
+		switch-phy-swap = <0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	compatible = "syscon", "simple-mfd";
+};
+
+&wmac {
+	status = "okay";
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&art 0x2>;
+};