ath79: add support for Buffalo WZR-HP-AG300H

Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
    WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
    Diag red, Movie Engine blue, USB green)

It is already supported by the ar71xx target.

For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>

Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
  - via TFTP rescue
  - via factory image
    - on firmware v1.77 (28-05-2012)
    - on pro firmware v24SP2 r30356 (26-03-2018)
  - via sysupgrade from ar71xx
    (wlan devices don't work because of new names)
  - via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)

Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>

2 files changed, 15 insertions, 8 deletions

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 6cd794e3d9..54fbe7b350 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -27,6 +27,11 @@ ath79_setup_interfaces()
 	wd,mynet-wifi-rangeextender)
 		ucidef_set_interface_lan "eth0"
 		;;
+	buffalo,wzr-hp-ag300h)
+		ucidef_set_interface_wan "eth1"
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
+		;;
 	buffalo,wzr-hp-g450h)
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 8c10cb8979..334e7056cf 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -156,15 +156,16 @@ case "$FIRMWARE" in
 	;;
 "ath9k-eeprom-pci-0000:00:11.0.bin")
 	case $board in
-	dlink,dir-825-b1)
-		ath9k_eeprom_extract "caldata" 4096 3768
-		ath9k_patch_fw_mac_crc $(mtd_get_mac_text "caldata" 65440) 524
-		;;
+	buffalo,wzr-hp-ag300h|\
 	netgear,wndr3700|\
 	netgear,wndr3700v2|\
 	netgear,wndr3800)
 		ath9k_eeprom_extract "art" 4096 3768
 		;;
+	dlink,dir-825-b1)
+		ath9k_eeprom_extract "caldata" 4096 3768
+		ath9k_patch_fw_mac_crc $(mtd_get_mac_text "caldata" 65440) 524
+		;;
 	*)
 		ath9k_eeprom_die "board $board is not supported yet"
 		;;
@@ -172,15 +173,16 @@ case "$FIRMWARE" in
 	;;
 "ath9k-eeprom-pci-0000:00:12.0.bin")
 	case $board in
-	dlink,dir-825-b1)
-		ath9k_eeprom_extract "caldata" 20480 3768
-		ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 65460) 1) 524
-		;;
+	buffalo,wzr-hp-ag300h|\
 	netgear,wndr3700|\
 	netgear,wndr3700v2|\
 	netgear,wndr3800)
 		ath9k_eeprom_extract "art" 20480 3768
 		;;
+	dlink,dir-825-b1)
+		ath9k_eeprom_extract "caldata" 20480 3768
+		ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 65460) 1) 524
+		;;
 	*)
 		ath9k_eeprom_die "board $board is not supported yet"
 		;;