aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files
diff options
context:
space:
mode:
authorDavid Bauer <mail@david-bauer.net>2018-08-08 22:13:44 +0200
committerMathias Kresin <dev@kresin.me>2018-08-09 18:44:57 +0200
commitc4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c (patch)
treec714a77976744b2c4dd86013962680f1e064478e /target/linux/ath79/base-files
parent387736af41444945da6a5e51748e91011569c03e (diff)
downloadupstream-c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c.tar.gz
upstream-c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c.tar.bz2
upstream-c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c.zip
ath79: add support for OCEDO Koala
This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ath79/base-files')
-rwxr-xr-xtarget/linux/ath79/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata4
2 files changed, 5 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 573bc80462..bbb30aa0cc 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -10,6 +10,7 @@ ath79_setup_interfaces()
case "$board" in
avm,fritz300e|\
+ ocedo,koala|\
ocedo,raccoon|\
pcs,cap324|\
tplink,re450-v2|\
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 038573f3e8..57d9744af2 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -87,6 +87,10 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
+ ocedo,koala)
+ ath10kcal_extract "art" 20480 2116
+ ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
+ ;;
openmesh,om5p-ac-v2)
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)