diff options
| author | Perry Melange <isprotejesvalkata@gmail.com> | 2019-08-07 19:25:13 +0200 |
|---|---|---|
| committer | David Bauer <mail@david-bauer.net> | 2019-08-07 21:17:40 +0200 |
| commit | 796ad2f7ef6fefcf821a3b21cadfdb7ef3126e95 (patch) | |
| tree | fe459a659f69dbd28bee860efa758ce19e875a80 /target/linux/ath79/base-files/etc | |
| parent | d7b4b5ec24184d322ccfc204c22120d5b4f02312 (diff) | |
| download | upstream-796ad2f7ef6fefcf821a3b21cadfdb7ef3126e95.tar.gz upstream-796ad2f7ef6fefcf821a3b21cadfdb7ef3126e95.tar.bz2 upstream-796ad2f7ef6fefcf821a3b21cadfdb7ef3126e95.zip | |
ath79: add support for D-Link DIR-842 C3
Hardware spec of DIR-842 C3:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
Diffstat (limited to 'target/linux/ath79/base-files/etc')
4 files changed, 5 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 35cb74db28..aad41b0dad 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -64,6 +64,7 @@ comfast,cf-e5) ;; dlink,dir-842-c1|\ dlink,dir-842-c2|\ +dlink,dir-842-c3|\ dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" ;; diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 9c6429984f..e3c1f423f1 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -123,6 +123,7 @@ ath79_setup_interfaces() dlink,dir-835-a1|\ dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ dlink,dir-859-a1|\ engenius,epg5000|\ tplink,archer-c2-v3|\ @@ -316,6 +317,7 @@ ath79_setup_macs() ;; dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ dlink,dir-859-a1|\ nec,wg1200cr|\ wd,mynet-n750) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index a7d482580b..62d53248bc 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -107,6 +107,7 @@ case "$FIRMWARE" in ;; dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ dlink,dir-859-a1|\ nec,wg1200cr|\ wd,mynet-n750) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index f6e2b801cb..501053e9d7 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -191,6 +191,7 @@ case "$FIRMWARE" in case $board in dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ nec,wg1200cr) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac) |