diff options
| author | INAGAKI Hiroshi <musashino.open@gmail.com> | 2018-11-30 19:04:23 +0900 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-12-06 20:26:57 +0100 |
| commit | 3358cae5238d66c73b0328b007a1cbb073bc8275 (patch) | |
| tree | 65011b51cf01491bfed2d6f61c5187eafa22bb23 /target/linux/ath79/base-files/etc | |
| parent | 9dd7147f6bce44a49fef594f55b120253baf5556 (diff) | |
| download | upstream-3358cae5238d66c73b0328b007a1cbb073bc8275.tar.gz upstream-3358cae5238d66c73b0328b007a1cbb073bc8275.tar.bz2 upstream-3358cae5238d66c73b0328b007a1cbb073bc8275.zip | |
ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.
WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.
There is no eeprom data for 5 GHz wlan in "art" partition.
Specification:
- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Diffstat (limited to 'target/linux/ath79/base-files/etc')
3 files changed, 11 insertions, 2 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 266a18791a..fa7a618909 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -82,6 +82,7 @@ ath79_setup_interfaces() iodata,etg3-r|\ iodata,wn-ac1167dgr|\ iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr|\ pcs,cr5000) ucidef_add_switch "switch0" \ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" @@ -223,7 +224,8 @@ ath79_setup_macs() wan_mac=$(macaddr_add "$lan_mac" -1) ;; iodata,wn-ac1167dgr|\ - iodata,wn-ac1600dgr2) + iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr) lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr) ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index c5cbac7514..e4d4a597a9 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -101,7 +101,8 @@ case "$FIRMWARE" in ath9k_eeprom_extract_reverse "urlader" 5441 1088 ;; iodata,wn-ac1167dgr|\ - iodata,wn-ac1600dgr2) + iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr) ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2 ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index fe5aa64a19..bb55b1c11c 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -13,6 +13,12 @@ PHYNBR=${DEVPATH##*/phy} board=$(board_name) case "$board" in + iodata,wn-ag300dgr) + # There is no eeprom data for 5 GHz wlan in "art" partition + # which would allow to patch the macaddress + [ "$PHYNBR" -eq 1 ] && \ + echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress + ;; phicomm,k2t) # The K2T factory firmware does use LAN mac address as the 2.4G wifi mac address [ "$PHYNBR" -eq 1 ] && \ |