ath79: add new OF only target for QCA MIPS silicon

This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.

Signed-off-by: John Crispin <john@phrozen.org>

5 files changed, 201 insertions, 0 deletions

diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
new file mode 100644
index 0000000000..9d42861939
--- /dev/null
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -0,0 +1,21 @@
+#!/bin/sh
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+"glinet,ar150")
+	ucidef_set_led_wlan "wlan" "WLAN" "gl-ar150:orange:wlan" "phy0tpt"
+	;;
+"tplink,tl-wr1043nd-v1")
+	ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
+	ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
+	;;
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
new file mode 100644
index 0000000000..941d2ab511
--- /dev/null
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -0,0 +1,44 @@
+#!/bin/sh
+
+. /lib/functions/system.sh
+. /lib/functions/uci-defaults.sh
+
+ath79_setup_interfaces()
+{
+	local board="$1"
+
+	case "$board" in
+	"ubnt,unifi")
+		ucidef_set_interface_lan "eth0"
+		;;
+
+	"tplink,tl-wr1043nd-v1")
+		ucidef_add_switch "switch0" \
+			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
+		;;
+	"netgear,wndr3800")
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		ucidef_add_switch "switch0" \
+			"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
+
+		ucidef_add_switch_attr "switch0" "blinkrate" 2
+		ucidef_add_switch_port_attr "switch0" 1 led 6
+		ucidef_add_switch_port_attr "switch0" 2 led 9
+		ucidef_add_switch_port_attr "switch0" 5 led 2
+		;;
+	"buffalo,wzr-hp-g450h")
+		ucidef_add_switch "switch0" \
+			"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
+		;;
+	*)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		;;
+	esac
+}
+
+board_config_update
+board=$(board_name)
+ath79_setup_interfaces $board
+board_config_flush
+
+exit 0
diff --git a/target/linux/ath79/base-files/etc/diag.sh b/target/linux/ath79/base-files/etc/diag.sh
new file mode 100644
index 0000000000..c9b32df94e
--- /dev/null
+++ b/target/linux/ath79/base-files/etc/diag.sh
@@ -0,0 +1,38 @@
+#!/bin/sh
+
+. /lib/functions/leds.sh
+
+get_status_led() {
+	local board=$(board_name)
+
+	case $board in
+	"glinet,ar150")
+		status_led="gl-ar150:orange:wlan"
+		;;
+	"tplink,tl-wr1043nd-v1")
+		status_led="tp-link:green:system"
+		;;
+	"ubnt,unifi")
+		status_led="ubnt:green:dome"
+		;;
+	esac
+}
+
+set_state() {
+	get_status_led
+
+	case "$1" in
+	preinit)
+		status_led_blink_preinit
+		;;
+	failsafe)
+		status_led_blink_failsafe
+		;;
+	preinit_regular)
+		status_led_blink_preinit_regular
+		;;
+	done)
+		status_led_on
+		;;
+	esac
+}
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
new file mode 100644
index 0000000000..fc15caea6f
--- /dev/null
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -0,0 +1,40 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+ath9k_eeprom_die() {
+	echo "ath9k eeprom: " "$*"
+	exit 1
+}
+
+ath9k_eeprom_extract() {
+	local part=$1
+	local offset=$2
+	local count=$3
+	local mtd
+
+	mtd=$(find_mtd_chardev $part)
+	[ -n "$mtd" ] || \
+		ath9k_eeprom_die "no mtd device found for partition $part"
+
+	dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+		ath9k_eeprom_die "failed to extract from $mtd"
+}
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath9k-eeprom-pci-0000:00:00.0.bin")
+	case $board in
+	"ubnt,unifi")
+		ath9k_eeprom_extract "art" 4096 2048
+		;;
+	*)
+		ath9k_eeprom_die "board $board is not supported yet"
+		;;
+	esac
+	;;
+esac
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
new file mode 100644
index 0000000000..2bbe5923bc
--- /dev/null
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -0,0 +1,58 @@
+#!/bin/sh
+
+ath10kcal_die() {
+	echo "ath10cal: " "$*"
+	exit 1
+}
+
+ath10kcal_from_file() {
+	local source=$1
+	local offset=$2
+	local count=$3
+
+	dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+		ath10kcal_die "failed to extract calibration data from $source"
+}
+
+ath10kcal_extract() {
+	local part=$1
+	local offset=$2
+	local count=$3
+	local mtd
+
+	mtd=$(find_mtd_chardev $part)
+	[ -n "$mtd" ] || \
+		ath10kcal_die "no mtd device found for partition $part"
+
+	dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+		ath10kcal_die "failed to extract calibration data from $mtd"
+}
+
+ath10kcal_patch_mac() {
+	local mac=$1
+
+	[ -z "$mac" ] && return
+
+	macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
+}
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath10k/cal-pci-0000:00:00.0.bin")
+	case $board in
+	openmesh,om5p-ac-v2)
+		ath10kcal_extract "ART" 20480 2116
+		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
+		;;
+	esac
+	;;
+*)
+	exit 1
+	;;
+esac