diff options
| author | David Bauer <mail@david-bauer.net> | 2018-12-27 02:32:38 +0100 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2018-12-27 14:06:38 +0100 |
| commit | 1724d4e9ed7716a5444eca42adf045c2f3afc554 (patch) | |
| tree | 633979e9b4ba8d4ca6693c06ac8aae889c6d3a49 /target/linux/ath79/base-files/etc | |
| parent | 8471944325db80ca37f7c756130070d0add58ff6 (diff) | |
| download | upstream-1724d4e9ed7716a5444eca42adf045c2f3afc554.tar.gz upstream-1724d4e9ed7716a5444eca42adf045c2f3afc554.tar.bz2 upstream-1724d4e9ed7716a5444eca42adf045c2f3afc554.zip | |
ath79: add support for devolo WiFi pro 1200e
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ath79/base-files/etc')
| -rwxr-xr-x | target/linux/ath79/base-files/etc/board.d/02_network | 3 | ||||
| -rw-r--r-- | target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 4 |
2 files changed, 7 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 5e1df97a87..b2c7762bb5 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -58,6 +58,9 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan" ;; + devolo,dvl1200e) + ucidef_set_interface_lan "eth0 eth1" + ;; dlink,dir-825-b1) ucidef_set_interface_wan "eth1" ucidef_add_switch "switch0" \ diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index da39fd7195..deaac72174 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -87,6 +87,10 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/cal-pci-0000:00:00.0.bin") case $board in + devolo,dvl1200e) + ath10kcal_extract "art" 20480 2116 + ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1) + ;; glinet,gl-x750) ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1) |