diff options
| author | INAGAKI Hiroshi <musashino.open@gmail.com> | 2019-03-16 13:27:32 +0900 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2019-04-06 19:14:06 +0200 |
| commit | 643fcfc8d64563d6c581a899ff839c9a91432e98 (patch) | |
| tree | 52c375338d37c21dcf61c80977666f9052ac119d /target/linux/ath79/base-files/etc/hotplug.d | |
| parent | fac27643f057d681ec276828dc4d1ba7159b5680 (diff) | |
| download | upstream-643fcfc8d64563d6c581a899ff839c9a91432e98.tar.gz upstream-643fcfc8d64563d6c581a899ff839c9a91432e98.tar.bz2 upstream-643fcfc8d64563d6c581a899ff839c9a91432e98.zip | |
ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.
Specification:
- SoC : Qualcomm Atheros QCA9563
- RAM : DDR2 128 MiB
- Flash : SPI-NOR 8 MiB
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : QCA9563 (SoC)
- 5 GHz : QCA9888
- Ethernet : 2x 10/100/1000 Mbps
- Switch : QCA8334
- LEDs/Input : 12x/4x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- JP1: Vcc, GND, NC, TX, RX from power connector side
- 115200 bps
Flash instruction using factory image:
1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing
Known issues:
- cannot be controlled LEDs other than Power (Green/Red)
- only Power LEDs are connected to SoC GPIO; other LEDs
connected to the gpiochip on ath10k chip (QCA9888)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
Diffstat (limited to 'target/linux/ath79/base-files/etc/hotplug.d')
| -rw-r--r-- | target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom | 4 | ||||
| -rw-r--r-- | target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 6 |
2 files changed, 10 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 72a768c554..90f8ca96d6 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -117,6 +117,10 @@ case "$FIRMWARE" in ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2 ;; + nec,wg1200cr) + ath9k_eeprom_extract "art" 4096 1088 + ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata wlan24mac) 2 + ;; nec,wg800hp) ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2 diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 4f13ae6521..8766862bb6 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -163,6 +163,12 @@ case "$FIRMWARE" in ;; "ath10k/pre-cal-pci-0000:00:00.0.bin") case $board in + nec,wg1200cr) + ath10kcal_extract "art" 20480 12064 + ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac) + ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ + /lib/firmware/ath10k/QCA9888/hw2.0/board.bin + ;; phicomm,k2t) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac") |