diff options
author | INAGAKI Hiroshi <musashino.open@gmail.com> | 2019-02-05 17:23:58 +0900 |
---|---|---|
committer | Christian Lamparter <chunkeey@gmail.com> | 2019-02-14 16:56:15 +0100 |
commit | 93d4439454247fb3f7cc88d8ad9a7e80bb440145 (patch) | |
tree | 53ab0ce7babe1c478e8285bef69a5b4ab926ccac /target/linux/ath79/base-files/etc/hotplug.d/ieee80211 | |
parent | cc8bd777723f32eca3d8643270dfc765cc772d1c (diff) | |
download | upstream-93d4439454247fb3f7cc88d8ad9a7e80bb440145.tar.gz upstream-93d4439454247fb3f7cc88d8ad9a7e80bb440145.tar.bz2 upstream-93d4439454247fb3f7cc88d8ad9a7e80bb440145.zip |
ath79: add support for I-O DATA WN-AC1600DGR
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- SoC: Qualcomm Atheros QCA9557
- RAM: 128 MB
- Flash: 16 MB
- WLAN: 2.4/5 GHz
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
- Switch: QCA8337N
- LED/key: 6x/6x(4x buttons, 1x slide switch)
- UART: through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Diffstat (limited to 'target/linux/ath79/base-files/etc/hotplug.d/ieee80211')
-rw-r--r-- | target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac | 6 |
1 files changed, 6 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 14d4f6b9d6..2da2e8bfb0 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -19,6 +19,12 @@ case "$board" in [ "$PHYNBR" -eq 1 ] && \ echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress ;; + iodata,wn-ac1600dgr) + # There is no eeprom data for 5 GHz wlan in "art" partition + # which would allow to patch the macaddress + [ "$PHYNBR" -eq 0 ] && \ + echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress + ;; phicomm,k2t) # The K2T factory firmware does use LAN mac address as the 2.4G wifi mac address [ "$PHYNBR" -eq 1 ] && \ |