aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
diff options
context:
space:
mode:
authorTomasz Maciej Nowak <tomek_n@o2.pl>2019-03-04 15:18:53 +0100
committerChristian Lamparter <chunkeey@gmail.com>2019-03-13 16:25:35 +0100
commitee34740ca3f90a5359392d629544e4520030e52e (patch)
treec0557dd0779d4005be44fba43dee8821824a58c3 /target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
parent41a86debe3c0a01e075e749d0bb1c6d631e35c32 (diff)
downloadupstream-ee34740ca3f90a5359392d629544e4520030e52e.tar.gz
upstream-ee34740ca3f90a5359392d629544e4520030e52e.tar.bz2
upstream-ee34740ca3f90a5359392d629544e4520030e52e.zip
ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Diffstat (limited to 'target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata')
-rw-r--r--target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata11
1 files changed, 6 insertions, 5 deletions
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 501a475571..cf8dcde711 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -102,6 +102,12 @@ case "$FIRMWARE" in
elecom,wrc-1750ghbk2-i)
ath10kcal_extract "ART" 20480 2116
;;
+ engenius,epg5000|\
+ iodata,wn-ac1167dgr|\
+ iodata,wn-ac1600dgr2)
+ ath10kcal_extract "art" 20480 2116
+ ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
+ ;;
engenius,ews511ap|\
glinet,gl-ar750s|\
glinet,gl-x750|\
@@ -109,11 +115,6 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
- iodata,wn-ac1167dgr|\
- iodata,wn-ac1600dgr2)
- ath10kcal_extract "art" 20480 2116
- ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
- ;;
nec,wg800hp)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)