diff options
| author | David Bauer <mail@david-bauer.net> | 2018-08-08 22:13:44 +0200 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-08-09 18:44:57 +0200 |
| commit | c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c (patch) | |
| tree | c714a77976744b2c4dd86013962680f1e064478e /target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | |
| parent | 387736af41444945da6a5e51748e91011569c03e (diff) | |
| download | upstream-c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c.tar.gz upstream-c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c.tar.bz2 upstream-c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c.zip | |
ath79: add support for OCEDO Koala
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata')
| -rw-r--r-- | target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 4 |
1 files changed, 4 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 038573f3e8..57d9744af2 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -87,6 +87,10 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/cal-pci-0000:00:00.0.bin") case $board in + ocedo,koala) + ath10kcal_extract "art" 20480 2116 + ath10kcal_patch_mac $(mtd_get_mac_binary art 12) + ;; openmesh,om5p-ac-v2) ath10kcal_extract "ART" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16) |