aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
diff options
context:
space:
mode:
authorChristian Lamparter <chunkeey@gmail.com>2018-09-04 23:27:02 +0200
committerJohn Crispin <john@phrozen.org>2018-09-10 09:07:41 +0200
commit745dee11ac787e9ffb4c15799961fa02d6462c8b (patch)
treed763015dd03d96cef2403434bc7a5cc8d54525a8 /target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
parentcd9c2492c18d1c2abd200e5911ad546d7c77a617 (diff)
downloadupstream-745dee11ac787e9ffb4c15799961fa02d6462c8b.tar.gz
upstream-745dee11ac787e9ffb4c15799961fa02d6462c8b.tar.bz2
upstream-745dee11ac787e9ffb4c15799961fa02d6462c8b.zip
ath79: add support for WD My Net Wi-Fi Range Extender
This patch ports over support for the device from ar71xx. SOC: AR7370 (Wasp - AR9344 rev2 0001974c) RAM: Winbond W9725G6KB-25 32MiB FLASH: Winbond 25Q64FVSIG 8MiB WLAN: AR9380 Dual-Band 802.11abgn 3x3:3 INPUT: WPS, RESET button (hardware on/off toggle button) LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high) Serial: Header Next to the winbond flash chip (labeld JP1) Pinout is GND - NC - RX - TX - 3V3 (JP1) The Serial setting is 115200-8-N-1. - Installation via uboot's upgrade command 0. attach serial cable 1. interrupt uboot and enter "upgrade code.bin" into the u-boot prompt ar7240> upgrade code.bin 2. rename openwrt...sysupgrade.bin to code.bin on PC 3. run a tftp-client on the PC (shell)$ tftp 192.168.1.230 binary put code.bin 4. wait for the device to finish [...] Copy buff to Flash from 0x9f040000 length 0x79f000 Copy to Flash... write addr: 9f040000 done 5. enter "go" in the u-boot prompt ar7240> go - TFTP ramdisk image boot from the uboot prompt (tftp server defaults to serverip 192.168.1.254) => tftpboot 81000000 initramfs.bin => bootm Tested and working: - LEDs - Buttons - Ethernet - Wi-Fi - OpenWRT sysupgrade For flashing and debricking information see: <https://openwrt.org/toh/wd/rext> Users coming from ar71xx can use sysupgrade too. But I highly advise to no save the old configuration and start from a clean state. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom')
-rw-r--r--target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom4
1 files changed, 4 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 1af6f96be0..8c10cb8979 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -145,6 +145,10 @@ case "$FIRMWARE" in
ubnt,unifi)
ath9k_eeprom_extract "art" 4096 2048
;;
+ wd,mynet-wifi-rangeextender)
+ ath9k_eeprom_extract "art" 4096 4096
+ ath9k_patch_fw_mac_crc $(nvram get wl0_hwaddr) "$mac" 2
+ ;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;