diff options
| author | Roger Pueyo Centelles <roger.pueyo@guifi.net> | 2018-12-29 20:44:43 +0100 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2019-02-28 11:26:10 +0100 |
| commit | 59c2f8af8c4400baffb09d6f8ab4d2826e38726a (patch) | |
| tree | d495cc764f35ee83d25e01bb245dad62df4c645b /target/linux/ath79/base-files/etc/board.d | |
| parent | e6f047fa368ca9c90691b93aa5e03068fe1f4178 (diff) | |
| download | upstream-59c2f8af8c4400baffb09d6f8ab4d2826e38726a.tar.gz upstream-59c2f8af8c4400baffb09d6f8ab4d2826e38726a.tar.bz2 upstream-59c2f8af8c4400baffb09d6f8ab4d2826e38726a.zip | |
ath79: add support for COMFAST CF-E120A v3
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Diffstat (limited to 'target/linux/ath79/base-files/etc/board.d')
| -rwxr-xr-x | target/linux/ath79/base-files/etc/board.d/01_leds | 9 |
1 files changed, 9 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 804f1fca82..a56fe58f76 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -38,6 +38,15 @@ comfast,cf-e110n-v2) ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssimediumhigh" "wlan0" "51" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh" "wlan0" "76" "100" ;; + comfast,cf-e120a-v3) + ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0" + ucidef_set_led_switch "wan" "WAN" "$boardname:green:wan" "switch0" "0x04" + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow" "wlan0" "1" "100" + ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "$boardname:red:rssimediumlow" "wlan0" "26" "100" + ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssimediumhigh" "wlan0" "51" "100" + ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh" "wlan0" "76" "100" + ;; dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" ;; |