linux: add support of Synopsys ARCHS38-based boards

This patch introduces support of new boards with ARC HS38 cores.

ARC HS38 is a new generation of ARC cores which utilize ARCv2 ISA.
As with ARC770 we're addind support for 2 boards for now:

 [1] Synopsys SDP board (AXS103)
     This is the same base-board as in AXS101 but with
     FPGA-based CPU-tile where ARCHs38 core is implemented.

 [2] nSIM
     Again this is the same simulation engine but configured for
     new instruction set and features of new CPU.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 48740

5 files changed, 486 insertions, 0 deletions

diff --git a/target/linux/archs38/dts/axc003_idu.dtsi b/target/linux/archs38/dts/axc003_idu.dtsi
new file mode 100644
index 0000000000..06a9f294a2
--- /dev/null
+++ b/target/linux/archs38/dts/axc003_idu.dtsi
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2014, 2015 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Device tree for AXC003 CPU card: HS38x2 (Dual Core) with IDU intc
+ */
+
+/ {
+	compatible = "snps,arc";
+	clock-frequency = <90000000>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpu_card {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		ranges = <0x00000000 0xf0000000 0x10000000>;
+
+		cpu_intc: archs-intc@cpu {
+			compatible = "snps,archs-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		idu_intc: idu-interrupt-controller {
+			compatible = "snps,archs-idu-intc";
+			interrupt-controller;
+			interrupt-parent = <&cpu_intc>;
+
+			/*
+			 * <hwirq  distribution>
+			 * distribution: 0=RR; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3
+			 */
+			#interrupt-cells = <2>;
+
+			/*
+			 * upstream irqs to core intc - downstream these are
+			 * "COMMON" irq 0,1..
+			 */
+			interrupts = <24 25>;
+		};
+
+		/*
+		 * this GPIO block ORs all interrupts on CPU card (creg,..)
+		 * to uplink only 1 IRQ to ARC core intc
+		 */
+		dw-apb-gpio@0x2000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = < 0x2000 0x80 >;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ictl_intc: gpio-controller@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <30>;
+				reg = <0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupt-parent = <&idu_intc>;
+
+				/*
+				 * cmn irq 1 -> cpu irq 25
+				 * Distribute to cpu0 only
+				 */
+				interrupts = <1 1>;
+			};
+		};
+
+		debug_uart: dw-apb-uart@0x5000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x5000 0x100>;
+			clock-frequency = <33333000>;
+			interrupt-parent = <&ictl_intc>;
+			interrupts = <2 4>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		arcpct0: pct {
+			compatible = "snps,archs-pct";
+			#interrupt-cells = <1>;
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <20>;
+		};
+	};
+
+	/*
+	 * This INTC is actually connected to DW APB GPIO
+	 * which acts as a wire between MB INTC and CPU INTC.
+	 * GPIO INTC is configured in platform init code
+	 * and here we mimic direct connection from MB INTC to
+	 * CPU INTC, thus we set "interrupts = <0 1>" instead of
+	 * "interrupts = <12>"
+	 *
+	 * This intc actually resides on MB, but we move it here to
+	 * avoid duplicating the MB dtsi file given that IRQ from
+	 * this intc to cpu intc are different for axs101 and axs103
+	 */
+	mb_intc: dw-apb-ictl@0xe0012000 {
+		#interrupt-cells = <1>;
+		compatible = "snps,dw-apb-ictl";
+		reg = < 0xe0012000 0x200 >;
+		interrupt-controller;
+		interrupt-parent = <&idu_intc>;
+		interrupts = <0 1>;	/* cmn irq 0 -> cpu irq 24
+					   distribute to cpu0 only */
+	};
+
+	memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0x80000000 0x40000000>;
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;	/* 512MiB */
+	};
+};
diff --git a/target/linux/archs38/dts/axs103_idu.dts b/target/linux/archs38/dts/axs103_idu.dts
new file mode 100644
index 0000000000..9c4bf0f28f
--- /dev/null
+++ b/target/linux/archs38/dts/axs103_idu.dts
@@ -0,0 +1,25 @@
+/*
+ * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Device Tree for AXS103 SDP with AXS10X Main Board and
+ * AXC003 FPGA Card (with SMP bitfile)
+ */
+/dts-v1/;
+
+/include/ "axc003_idu.dtsi"
+/include/ "axs10x_mb.dtsi"
+
+/ {
+	model = "Synopsys AXS103 Development Board";
+	compatible = "snps,axs103", "snps,arc-sdp";
+
+	chosen {
+		bootargs = "earlycon=uart8250,mmio32,0xe0022000,115200n8 console=ttyS3,115200n8";
+	};
+};
diff --git a/target/linux/archs38/dts/axs10x_mb.dtsi b/target/linux/archs38/dts/axs10x_mb.dtsi
new file mode 100644
index 0000000000..44a578c107
--- /dev/null
+++ b/target/linux/archs38/dts/axs10x_mb.dtsi
@@ -0,0 +1,225 @@
+/*
+ * Support for peripherals on the AXS10x mainboard
+ *
+ * Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	axs10x_mb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0xe0000000 0x10000000>;
+		interrupt-parent = <&mb_intc>;
+
+		clocks {
+			i2cclk: i2cclk {
+				compatible = "fixed-clock";
+				clock-frequency = <50000000>;
+				#clock-cells = <0>;
+			};
+
+			apbclk: apbclk {
+				compatible = "fixed-clock";
+				clock-frequency = <50000000>;
+				#clock-cells = <0>;
+			};
+
+			mmcclk: mmcclk {
+				compatible = "fixed-clock";
+				clock-frequency = <50000000>;
+				#clock-cells = <0>;
+			};
+		};
+
+		ethernet@0x18000 {
+			#interrupt-cells = <1>;
+			compatible = "snps,dwmac";
+			reg = < 0x18000 0x2000 >;
+			interrupts = < 4 >;
+			interrupt-names = "macirq";
+			phy-mode = "rgmii";
+			snps,pbl = < 32 >;
+			clocks = <&apbclk>;
+			clock-names = "stmmaceth";
+			max-speed = <100>;
+		};
+
+		ehci@0x40000 {
+			compatible = "generic-ehci";
+			reg = < 0x40000 0x100 >;
+			interrupts = < 8 >;
+		};
+
+		ohci@0x60000 {
+			compatible = "generic-ohci";
+			reg = < 0x60000 0x100 >;
+			interrupts = < 8 >;
+		};
+
+		/*
+		 * According to DW Mobile Storage databook it is required
+		 * to use  "Hold Register" if card is enumerated in SDR12 or
+		 * SDR25 modes.
+		 *
+		 * Utilization of "Hold Register" is already implemented via
+		 * dw_mci_pltfm_prepare_command() which in its turn gets
+		 * used through dw_mci_drv_data->prepare_command call-back.
+		 * This call-back is used in Altera Socfpga platform and so
+		 * we may reuse it saying that we're compatible with their
+		 * "altr,socfpga-dw-mshc".
+		 *
+		 * Most probably "Hold Register" utilization is platform-
+		 * independent requirement which means that single unified
+		 * "snps,dw-mshc" should be enough for all users of DW MMC once
+		 * dw_mci_pltfm_prepare_command() is used in generic platform
+		 * code.
+		 */
+		mmc@0x15000 {
+			compatible = "altr,socfpga-dw-mshc";
+			reg = < 0x15000 0x400 >;
+			num-slots = < 1 >;
+			fifo-depth = < 16 >;
+			card-detect-delay = < 200 >;
+			clocks = <&apbclk>, <&mmcclk>;
+			clock-names = "biu", "ciu";
+			interrupts = < 7 >;
+			bus-width = < 4 >;
+		};
+
+		uart@0x20000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x20000 0x100>;
+			clock-frequency = <33333333>;
+			interrupts = <17>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		uart@0x21000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x21000 0x100>;
+			clock-frequency = <33333333>;
+			interrupts = <18>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		/* UART muxed with USB data port (ttyS3) */
+		uart@0x22000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x22000 0x100>;
+			clock-frequency = <33333333>;
+			interrupts = <19>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		i2c@0x1d000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x1d000 0x100>;
+			clock-frequency = <400000>;
+			clocks = <&i2cclk>;
+			interrupts = <14>;
+		};
+
+		i2c@0x1e000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x1e000 0x100>;
+			clock-frequency = <400000>;
+			clocks = <&i2cclk>;
+			interrupts = <15>;
+		};
+
+		i2c@0x1f000 {
+			compatible = "snps,designware-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f000 0x100>;
+			clock-frequency = <400000>;
+			clocks = <&i2cclk>;
+			interrupts = <16>;
+
+			eeprom@0x54{
+				compatible = "24c01";
+				reg = <0x54>;
+				pagesize = <0x8>;
+			};
+
+			eeprom@0x57{
+				compatible = "24c04";
+				reg = <0x57>;
+				pagesize = <0x8>;
+			};
+		};
+
+		gpio0:gpio@13000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x13000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio0_banka: gpio-controller@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+				reg = <0>;
+			};
+
+			gpio0_bankb: gpio-controller@1 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <8>;
+				reg = <1>;
+			};
+
+			gpio0_bankc: gpio-controller@2 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <8>;
+				reg = <2>;
+			};
+		};
+
+		gpio1:gpio@14000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x14000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio1_banka: gpio-controller@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <30>;
+				reg = <0>;
+			};
+
+			gpio1_bankb: gpio-controller@1 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <10>;
+				reg = <1>;
+			};
+
+			gpio1_bankc: gpio-controller@2 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <8>;
+				reg = <2>;
+			};
+		};
+	};
+};
diff --git a/target/linux/archs38/dts/nsim_hs_idu.dts b/target/linux/archs38/dts/nsim_hs_idu.dts
new file mode 100644
index 0000000000..75f539bb0d
--- /dev/null
+++ b/target/linux/archs38/dts/nsim_hs_idu.dts
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+/ {
+	model = "Synopsys ARC HS38 nSIM simulator";
+	compatible = "snps,nsim_hs";
+	interrupt-parent = <&core_intc>;
+
+	chosen {
+		bootargs = "earlycon=arc_uart,mmio32,0xc0fc1000,115200n8 console=ttyARC0,115200n8";
+	};
+
+	aliases {
+		serial0 = &arcuart0;
+	};
+
+	fpga {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* child and parent address space 1:1 mapped */
+		ranges;
+
+		core_intc: core-interrupt-controller {
+			compatible = "snps,archs-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		idu_intc: idu-interrupt-controller {
+			compatible = "snps,archs-idu-intc";
+			interrupt-controller;
+			interrupt-parent = <&core_intc>;
+
+			/*
+			 * <hwirq  distribution>
+			 * distribution: 0=RR; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3
+			 */
+			#interrupt-cells = <2>;
+
+			/*
+			 * upstream irqs to core intc - downstream these are
+			 * "COMMON" irq 0,1..
+			 */
+			interrupts = <24 25 26 27 28 29 30 31>;
+		};
+
+		arcuart0: serial@c0fc1000 {
+			compatible = "snps,arc-uart";
+			reg = <0xc0fc1000 0x100>;
+			interrupt-parent = <&idu_intc>;
+			interrupts = <0 0>;
+			clock-frequency = <80000000>;
+			current-speed = <115200>;
+			status = "okay";
+		};
+
+		arcpct0: pct {
+			compatible = "snps,archs-pct";
+			#interrupt-cells = <1>;
+			interrupts = <20>;
+		};
+	};
+};
diff --git a/target/linux/archs38/dts/skeleton.dtsi b/target/linux/archs38/dts/skeleton.dtsi
new file mode 100644
index 0000000000..296d371a33
--- /dev/null
+++ b/target/linux/archs38/dts/skeleton.dtsi
@@ -0,0 +1,37 @@
+/*
+ * Copyright (C) 2012 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Skeleton device tree; the bare minimum needed to boot; just include and
+ * add a compatible value.
+ */
+
+/ {
+	compatible = "snps,arc";
+	clock-frequency = <80000000>;	/* 80 MHZ */
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+	aliases { };
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "snps,arc770d";
+			reg = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;	/* 256M */
+	};
+};