ar71xx:add support for E558 v2

Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>

12 files changed, 217 insertions, 0 deletions

diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index b0f4975e5c..3db4305043 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -372,6 +372,9 @@ e1700ac-v2)
 	ucidef_set_led_usbdev "usb" "USB" "$board:green:usb" "1-1"
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
 	;;
+e558-v2)
+	ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
+	;;
 esr900)
 	ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "engenius:blue:wlan-2g" "phy0tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "engenius:blue:wlan-5g" "phy1tpt"
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index c04ecc838e..be5d9ad95d 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -390,6 +390,11 @@ ar71xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:lan" "3:wan"
 		;;
+	e558-v2)
+		ucidef_set_interfaces_lan_wan "eth1.1" "eth0.2"
+		ucidef_add_switch "switch0" \
+			"0@eth1" "4:lan" "5:lan" "6@eth0"  "3:wan"
+		;;
 	ebr-2310-c1)
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth1"
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 129df16097..2a2fda3ac8 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -24,6 +24,7 @@ get_status_led() {
 	antminer-s3|\
 	antminer-r1|\
 	e1700ac-v2|\
+	e558-v2|\
 	e600gac-v2|\
 	eap120|\
 	minibox-v1|\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 82b902545c..7c0d53b4cb 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -675,6 +675,9 @@ ar71xx_board_detect() {
 	*"E2100L")
 		name="e2100l"
 		;;
+	*"E558 v2")
+		name="e558-v2"
+		;;
 	*"E600G v2")
 		name="e600g-v2"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 3607fc22a6..2110eb238e 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -250,6 +250,7 @@ platform_check_image() {
 	dr531|\
 	dragino2|\
 	e1700ac-v2|\
+	e558-v2|\
 	e600g-v2|\
 	e600gac-v2|\
 	ebr-2310-c1|\
diff --git a/target/linux/ar71xx/config-4.9 b/target/linux/ar71xx/config-4.9
index ffee43d12e..58cd40962a 100644
--- a/target/linux/ar71xx/config-4.9
+++ b/target/linux/ar71xx/config-4.9
@@ -101,6 +101,7 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_DRAGINO2 is not set
 # CONFIG_ATH79_MACH_E1700AC_V2 is not set
 # CONFIG_ATH79_MACH_E2100L is not set
+# CONFIG_ATH79_MACH_E558_V2 is not set
 # CONFIG_ATH79_MACH_E600G_V2 is not set
 # CONFIG_ATH79_MACH_EAP120 is not set
 # CONFIG_ATH79_MACH_EAP300V2 is not set
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 4ae6e6dcc8..3cd90a446b 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -711,6 +711,17 @@ config ATH79_MACH_E2100L
 	select ATH79_DEV_WMAC
 	select ATH79_NVRAM
 
+config ATH79_MACH_E558_V2
+	bool "Qxwlan E558 v2 support"
+	select SOC_QCA955X
+	select ATH79_DEV_AP9X_PCI if PCI
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_E600G_V2
 	bool "Qxwlan E600G/E600GAC v2 support"
 	select SOC_QCA953X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 996fd4c68a..690738e1e6 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -112,6 +112,7 @@ obj-$(CONFIG_ATH79_MACH_DR344)			+= mach-dr344.o
 obj-$(CONFIG_ATH79_MACH_DR531)			+= mach-dr531.o
 obj-$(CONFIG_ATH79_MACH_DRAGINO2)		+= mach-dragino2.o
 obj-$(CONFIG_ATH79_MACH_E1700AC_V2)		+= mach-e1700ac-v2.o
+obj-$(CONFIG_ATH79_MACH_E558_V2)		+= mach-e558-v2.o
 obj-$(CONFIG_ATH79_MACH_E600G_V2)		+= mach-e600g-v2.o
 obj-$(CONFIG_ATH79_MACH_EAP120)			+= mach-eap120.o
 obj-$(CONFIG_ATH79_MACH_EAP300V2)		+= mach-eap300v2.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c
new file mode 100644
index 0000000000..c067d58bbb
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c
@@ -0,0 +1,170 @@
+/*
+ * Qxwlan E558 v2 board support
+ *
+ *  Copyright (C) 2017 Peng Zhang <sd20@qxwlan.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define E558_V2_GPIO_LED_WLAN	13
+#define E558_V2_GPIO_LED_SYSTEM	14
+#define E558_V2_GPIO_LED_QSS	15
+
+#define E558_V2_GPIO_BTN_RESET	16
+
+#define E558_V2_KEYS_POLL_INTERVAL	20	/* msecs */
+#define E558_V2_KEYS_DEBOUNCE_INTERVAL (3 * E558_V2_KEYS_POLL_INTERVAL)
+
+static struct gpio_led e558_v2_leds_gpio[] __initdata = {
+	{
+		.name		= "e558-v2:green:qss",
+		.gpio		= E558_V2_GPIO_LED_QSS,
+		.active_low	= 1,
+	},
+	{
+		.name		= "e558-v2:green:system",
+		.gpio		= E558_V2_GPIO_LED_SYSTEM,
+		.active_low	= 1,
+	},
+	{
+		.name		= "e558-v2:green:wlan",
+		.gpio		= E558_V2_GPIO_LED_WLAN,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button e558_v2_gpio_keys[] __initdata = {
+	{
+		.desc		= "reset",
+		.type		= EV_KEY,
+		.code		= KEY_RESTART,
+		.debounce_interval = E558_V2_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= E558_V2_GPIO_BTN_RESET,
+		.active_low	= 1,
+	},
+};
+
+/* GMAC0 of the AR8327 switch is connected to the QCA9558 SoC via SGMII */
+static struct ar8327_pad_cfg e558_v2_ar8327_pad0_cfg = {
+	.mode = AR8327_PAD_MAC_SGMII,
+	.sgmii_delay_en = true,
+};
+
+/* GMAC6 of the AR8327 switch is connected to the QCA9558 SoC via RGMII */
+static struct ar8327_pad_cfg e558_v2_ar8327_pad6_cfg = {
+	.mode = AR8327_PAD_MAC_RGMII,
+	.txclk_delay_en = true,
+	.rxclk_delay_en = true,
+	.txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
+	.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
+};
+
+static const struct ar8327_led_info e558_v2_leds_qca8334[] = {
+	AR8327_LED_INFO(PHY2_0, HW, "e558-v2:green:wan"),
+	AR8327_LED_INFO(PHY3_0, HW, "e558-v2:green:lan1"),
+	AR8327_LED_INFO(PHY4_0, HW, "e558-v2:green:lan2"),
+};
+
+static struct ar8327_led_cfg e558_v2_ar8327_led_cfg = {
+	.led_ctrl0 = 0xc737c737,
+	.led_ctrl1 = 0x00000000,
+	.led_ctrl2 = 0x00000000,
+	.led_ctrl3 = 0x0030c300,
+	.open_drain = false,
+};
+
+static struct ar8327_platform_data e558_v2_ar8327_data = {
+	.pad0_cfg = &e558_v2_ar8327_pad0_cfg,
+	.pad6_cfg = &e558_v2_ar8327_pad6_cfg,
+	.port0_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+	.port6_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+	.led_cfg = &e558_v2_ar8327_led_cfg,
+	.leds = e558_v2_leds_qca8334,
+	.num_leds = ARRAY_SIZE(e558_v2_leds_qca8334),
+};
+
+static struct mdio_board_info e558_v2_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 0,
+		.platform_data = &e558_v2_ar8327_data,
+	},
+};
+
+static void __init e558_v2_setup(void)
+{
+	u8 *mac = (u8 *) KSEG1ADDR(0x1f050400);
+	u8 *art = (u8 *) KSEG1ADDR(0x1f061000);
+
+	ath79_register_m25p80(NULL);
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(e558_v2_leds_gpio),
+				 e558_v2_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, E558_V2_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(e558_v2_gpio_keys),
+					e558_v2_gpio_keys);
+
+	ath79_register_mdio(0, 0x0);
+	mdiobus_register_board_info(e558_v2_mdio0_info,
+				    ARRAY_SIZE(e558_v2_mdio0_info));
+
+	ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN);
+
+	/* GMAC0 is connected to the RMGII interface */
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+	ath79_eth0_pll_data.pll_1000 = 0x56000000;
+	ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
+	ath79_register_eth(0);
+
+	/* GMAC1 is connected to the SGMII interface */
+	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+	ath79_eth1_data.speed = SPEED_1000;
+	ath79_eth1_data.duplex = DUPLEX_FULL;
+	ath79_eth1_pll_data.pll_1000 = 0x03000101;
+	ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
+	ath79_register_eth(1);
+
+	ath79_register_pci();
+	ath79_register_usb();
+	ath79_register_wmac(art, NULL);
+}
+
+MIPS_MACHINE(ATH79_MACH_E558_V2, "E558-V2", "Qxwlan E558 v2",
+		e558_v2_setup);
+
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 09b62ddee8..de1efab3a2 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -105,6 +105,7 @@ enum ath79_mach_type {
 	ATH79_MACH_DR531,			/* Wallys DR531 */
 	ATH79_MACH_DRAGINO2,			/* Dragino Version 2 */
 	ATH79_MACH_E1700AC_V2,			/* Qxwlan E1700AC v2 */
+	ATH79_MACH_E558_V2,			/* Qxwlan E558 v2 */
 	ATH79_MACH_E600G_V2,			/* Qxwlan E600G v2 */
 	ATH79_MACH_E600GAC_V2,			/* Qxwlan E600GAC v2 */
 	ATH79_MACH_EAP120,			/* TP-LINK EAP120 */
diff --git a/target/linux/ar71xx/generic/config-default b/target/linux/ar71xx/generic/config-default
index 98c40f870e..df492da60e 100644
--- a/target/linux/ar71xx/generic/config-default
+++ b/target/linux/ar71xx/generic/config-default
@@ -73,6 +73,7 @@ CONFIG_ATH79_MACH_DR531=y
 CONFIG_ATH79_MACH_DRAGINO2=y
 CONFIG_ATH79_MACH_E1700AC_V2=y
 CONFIG_ATH79_MACH_E2100L=y
+CONFIG_ATH79_MACH_E558_V2=y
 CONFIG_ATH79_MACH_E600G_V2=y
 CONFIG_ATH79_MACH_EAP120=y
 CONFIG_ATH79_MACH_EAP300V2=y
diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
index 3da57e4698..dedc19d52c 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -326,6 +326,25 @@ define Device/e1700ac-v2-8M
 endef
 TARGET_DEVICES += e1700ac-v2-8M
 
+define Device/e558-v2-16M
+  DEVICE_TITLE := Qxwlan E558 v2 (16MB flash)
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 -swconfig
+  BOARDNAME := E558-V2
+  SUPPORTED_DEVICES := e558-v2
+  IMAGE_SIZE := 15936k
+  MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art),-(firmware)
+  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+	append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e558-v2-16M
+
+define Device/e558-v2-8M
+  $(Device/e558-v2-16M)
+  DEVICE_TITLE := Qxwlan E558 v2 (8MB flash)
+  IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e558-v2-8M
+
 define Device/e600g-v2-16M
   DEVICE_TITLE := Qxwlan E600G v2 (16MB flash)
   DEVICE_PACKAGES := kmod-usb-core kmod-usb2 -swconfig