diff options
| author | Petr Štetiar <ynezz@true.cz> | 2018-11-17 08:01:55 +0100 |
|---|---|---|
| committer | Petr Štetiar <ynezz@true.cz> | 2019-04-08 18:37:04 +0200 |
| commit | 0f8cdc28af2619d412b4a8f594b77ac6e7d27edd (patch) | |
| tree | 9890f9edb484c7edbd97d61bcdc63c032d67d099 /target/linux/ar71xx/base-files | |
| parent | 6009b3fd586a1fd91400074080afb9545c6cf7e2 (diff) | |
| download | upstream-0f8cdc28af2619d412b4a8f594b77ac6e7d27edd.tar.gz upstream-0f8cdc28af2619d412b4a8f594b77ac6e7d27edd.tar.bz2 upstream-0f8cdc28af2619d412b4a8f594b77ac6e7d27edd.zip | |
ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Diffstat (limited to 'target/linux/ar71xx/base-files')
5 files changed, 7 insertions, 0 deletions
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 79f452d8cf..41dd8c52ea 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -179,6 +179,7 @@ bsb) ucidef_set_led_default "sys" "SYS" "$board:red:sys" "1" ;; bullet-m|\ +bullet-m-xw|\ loco-m-xw|\ nanostation-m|\ nanostation-m-xw|\ diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index a7b97bb3dd..8e5ff101d6 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -68,6 +68,7 @@ ar71xx_setup_interfaces() ap91-5g|\ aw-nr580|\ bullet-m|\ + bullet-m-xw|\ c-55|\ cap324|\ cap4200ag|\ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 55654263af..558f338cd6 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -129,6 +129,7 @@ get_status_led() { status_led="$board:red:sys" ;; bullet-m|\ + bullet-m-xw|\ loco-m-xw|\ nano-m|\ nanostation-m|\ diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 56a4fab80c..990683a55b 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -530,6 +530,9 @@ ar71xx_board_detect() { name="bullet-m" ubnt_xm_board_detect ;; + *"Bullet M XW") + name="bullet-m-xw" + ;; *"BXU2000n-2 rev. A1") name="bxu2000n-2-a1" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 7fc3d4e3b3..81735017e5 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -218,6 +218,7 @@ platform_check_image() { archer-c7-v4|\ archer-c7-v5|\ bullet-m|\ + bullet-m-xw|\ c-55|\ carambola2|\ cf-e316n-v2|\ |