aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files/lib/ar71xx.sh
diff options
context:
space:
mode:
authorPiotr Dymacz <pepe2k@gmail.com>2017-03-16 00:54:08 +0100
committerPiotr Dymacz <pepe2k@gmail.com>2017-03-23 17:59:47 +0100
commit4436979c83e0d9ef4d7c3162e9d573bb521f61ff (patch)
tree04aa1a21b5537e00a312314fb179d17fa63d43cf /target/linux/ar71xx/base-files/lib/ar71xx.sh
parent0d9adb4832e2c9ef4303b0b7aeff86c0ed4e5d89 (diff)
downloadupstream-4436979c83e0d9ef4d7c3162e9d573bb521f61ff.tar.gz
upstream-4436979c83e0d9ef4d7c3162e9d573bb521f61ff.tar.bz2
upstream-4436979c83e0d9ef4d7c3162e9d573bb521f61ff.zip
ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ar71xx/base-files/lib/ar71xx.sh')
-rwxr-xr-xtarget/linux/ar71xx/base-files/lib/ar71xx.sh6
1 files changed, 6 insertions, 0 deletions
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 267cb6ad58..eedcb7829c 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -508,6 +508,9 @@ ar71xx_board_detect() {
name="cpe210"
tplink_pharos_board_detect
;;
+ *"CPE505N")
+ name="cpe505n"
+ ;;
*"CPE510/520")
name="cpe510"
tplink_pharos_board_detect
@@ -802,6 +805,9 @@ ar71xx_board_detect() {
*"Qihoo 360 C301")
name="qihoo-c301"
;;
+ *"R602N")
+ name="r602n"
+ ;;
*"R6100")
name="r6100"
;;