diff options
| author | Piotr Dymacz <pepe2k@gmail.com> | 2018-01-05 11:35:45 +0100 |
|---|---|---|
| committer | Piotr Dymacz <pepe2k@gmail.com> | 2018-01-14 21:30:16 +0100 |
| commit | 4b0eebe9dfa49f995474322f2c6998026534a5f8 (patch) | |
| tree | 22e8ca9428a42da7aa590188145c3d408f749fc4 /target/linux/ar71xx/base-files/etc | |
| parent | 62610129b23db2ff995191940b88a6e56d0a87d6 (diff) | |
| download | upstream-4b0eebe9dfa49f995474322f2c6998026534a5f8.tar.gz upstream-4b0eebe9dfa49f995474322f2c6998026534a5f8.tar.bz2 upstream-4b0eebe9dfa49f995474322f2c6998026534a5f8.zip | |
ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ar71xx/base-files/etc')
| -rwxr-xr-x | target/linux/ar71xx/base-files/etc/board.d/01_leds | 10 | ||||
| -rw-r--r-- | target/linux/ar71xx/base-files/etc/diag.sh | 3 |
2 files changed, 11 insertions, 2 deletions
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 97bf33052c..f2d66b2986 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -129,13 +129,21 @@ dr531) ;; esac ;; -ap91-5g) +ap91-5g|\ +n5q) ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" ucidef_set_rssimon "wlan0" "200000" "1" ucidef_set_led_rssi "signal1" "SIGNAL1" "$board:red:signal1" "wlan0" "1" "100" ucidef_set_led_rssi "signal2" "SIGNAL2" "$board:orange:signal2" "wlan0" "25" "100" ucidef_set_led_rssi "signal3" "SIGNAL3" "$board:green:signal3" "wlan0" "50" "100" ucidef_set_led_rssi "signal4" "SIGNAL4" "$board:green:signal4" "wlan0" "75" "100" + + case "$board" in + n5q) + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ;; + esac ;; bhr-4grv2) ucidef_set_led_default "power" "POWER" "buffalo:green:power" "1" diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 2f2d2c3103..63a9ebc1ec 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -80,7 +80,8 @@ get_status_led() { gl-mifi) status_led="$board:green:lan" ;; - ap91-5g) + ap91-5g|\ + n5q) status_led="$board:green:signal4" ;; ap96) |