diff options
| author | David Bauer <mail@david-bauer.net> | 2018-04-24 19:52:13 +0200 |
|---|---|---|
| committer | John Crispin <john@phrozen.org> | 2018-05-07 10:42:26 +0200 |
| commit | b6a4c674684585902ee07a4ba7c89d988d633650 (patch) | |
| tree | 37fe2cf0fcaf56bd88f3a5b293acd2337ba60cfd /target/linux/ar71xx/base-files/etc | |
| parent | 66c8afd115f4d03fefc0e650b90dd922487cc50f (diff) | |
| download | upstream-b6a4c674684585902ee07a4ba7c89d988d633650.tar.gz upstream-b6a4c674684585902ee07a4ba7c89d988d633650.tar.bz2 upstream-b6a4c674684585902ee07a4ba7c89d988d633650.zip | |
ar71xx: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ar71xx/base-files/etc')
3 files changed, 10 insertions, 0 deletions
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 906c4b715f..52f1ac3ecf 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -372,6 +372,12 @@ epg5000) ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "$board:blue:wlan-2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "$board:blue:wlan-5g" "phy0tpt" ;; +fritz4020) + ucidef_set_led_default "power" "Power" "$board:green:power" "1" + ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth1" + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0" + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ;; gl-ar300m) ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt" ;; diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index cbbcf53946..5898261b3d 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -243,6 +243,7 @@ ar71xx_setup_interfaces() ;; archer-c58-v1|\ archer-c59-v1|\ + fritz4020|\ rb-450g) ucidef_set_interfaces_lan_wan "eth1.1" "eth0" ucidef_add_switch "switch0" \ diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 41ab43f7cb..6eb946468d 100644 --- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -75,6 +75,9 @@ case "$FIRMWARE" in ath9k_eeprom_extract "art" 4096 2048 ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1) ;; + fritz4020) + ath9k_eeprom_extract_reverse "urlader" 5441 1088 + ;; mr18) . /lib/upgrade/nand.sh |