diff options
| author | Marek Lindner <marek.lindner@kaiwoo.ai> | 2018-11-25 21:46:54 +0800 |
|---|---|---|
| committer | Petr Štetiar <ynezz@true.cz> | 2020-12-22 19:11:50 +0100 |
| commit | ea5bb6bbfee06f44f714aff40c8929505face221 (patch) | |
| tree | c3ae619246530a997fffbc38ffde4a2e80b357e7 /package | |
| parent | 8a891bfaa01d9592ea86c6b0cbbd5c04688c09f8 (diff) | |
| download | upstream-ea5bb6bbfee06f44f714aff40c8929505face221.tar.gz upstream-ea5bb6bbfee06f44f714aff40c8929505face221.tar.bz2 upstream-ea5bb6bbfee06f44f714aff40c8929505face221.zip | |
ipq40xx: add support for Plasma Cloud PA1200
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Diffstat (limited to 'package')
| -rw-r--r-- | package/boot/uboot-envtools/files/ipq40xx | 3 | ||||
| -rw-r--r-- | package/firmware/ipq-wifi/Makefile | 2 | ||||
| -rw-r--r-- | package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 | bin | 0 -> 24324 bytes |
3 files changed, 4 insertions, 1 deletions
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index 27aab6b286..9252c0ffac 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -36,7 +36,8 @@ edgecore,ecw5211 |\ glinet,gl-b1300 |\ luma,wrtq-329acn |\ openmesh,a42 |\ -openmesh,a62) +openmesh,a62 |\ +plasmacloud,pa1200) ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000" ;; buffalo,wtr-m2133hp) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 9aa6852046..e26269a710 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -42,6 +42,7 @@ ALLWIFIBOARDS:= \ linksys_mr8300-v0 \ luma_wrtq-329acn \ mobipromo_cm520-79f \ + plasmacloud_pa1200 \ qxwlan_e2600ac ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) @@ -120,6 +121,7 @@ $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300)) $(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN)) $(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F)) +$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 b/package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 Binary files differnew file mode 100644 index 0000000000..99d6df8c8c --- /dev/null +++ b/package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 |