iwinfo: add per-station rate and mcs info to assoclist op

SVN-Revision: 30682

4 files changed, 1073 insertions, 33 deletions

diff --git a/package/iwinfo/src/include/iwinfo.h b/package/iwinfo/src/include/iwinfo.h
index 40b85a0492..72e2333617 100644
--- a/package/iwinfo/src/include/iwinfo.h
+++ b/package/iwinfo/src/include/iwinfo.h
@@ -49,10 +49,22 @@ extern const char *IWINFO_KMGMT_NAMES[];
 extern const char *IWINFO_AUTH_NAMES[];
 
 
+struct iwinfo_rate_entry {
+	uint16_t rate;
+	uint8_t mcs;
+	uint8_t is_40mhz:1;
+	uint8_t is_short_gi:1;
+};
+
 struct iwinfo_assoclist_entry {
 	uint8_t	mac[6];
 	int8_t signal;
 	int8_t noise;
+	uint32_t inactive;
+	uint32_t rx_packets;
+	uint32_t tx_packets;
+	struct iwinfo_rate_entry rx_rate;
+	struct iwinfo_rate_entry tx_rate;
 };
 
 struct iwinfo_txpwrlist_entry {
diff --git a/package/iwinfo/src/include/iwinfo/api/broadcom.h b/package/iwinfo/src/include/iwinfo/api/broadcom.h
index bae69c7f75..50eedd9e49 100644
--- a/package/iwinfo/src/include/iwinfo/api/broadcom.h
+++ b/package/iwinfo/src/include/iwinfo/api/broadcom.h
@@ -64,6 +64,30 @@ typedef struct wl_sta_rssi {
 	uint16_t				foo;
 } wl_sta_rssi_t;
 
+#define WL_NUMRATES     255 /* max # of rates in a rateset */
+typedef struct wl_rateset {
+    uint32_t  				count;          /* # rates in this set */
+    uint8_t   				rates[WL_NUMRATES]; /* rates in 500kbps units w/hi bit set if basic */
+} wl_rateset_t;
+
+typedef struct wl_sta_info {
+    uint16_t				ver;        /* version of this struct */
+    uint16_t				len;        /* length in bytes of this structure */
+    uint16_t				cap;        /* sta's advertised capabilities */
+    uint32_t				flags;      /* flags defined below */
+    uint32_t				idle;       /* time since data pkt rx'd from sta */
+    unsigned char			ea[6];      /* Station address */
+    wl_rateset_t			rateset;    /* rateset in use */
+    uint32_t				in;   		/* seconds elapsed since associated */
+    uint32_t				listen_interval_inms; /* Min Listen interval in ms for this STA */
+    uint32_t				tx_pkts;    /* # of packets transmitted */
+    uint32_t				tx_failures;    /* # of packets failed */
+    uint32_t				rx_ucast_pkts;  /* # of unicast packets received */
+    uint32_t				rx_mcast_pkts;  /* # of multicast packets received */
+    uint32_t				tx_rate;    /* Rate of last successful tx frame */
+    uint32_t				rx_rate;    /* Rate of last successful rx frame */
+} wl_sta_info_t;
+
 typedef struct wlc_ssid {
 	uint32_t				ssid_len;
 	unsigned char			ssid[32];
diff --git a/package/iwinfo/src/include/iwinfo/api/madwifi.h b/package/iwinfo/src/include/iwinfo/api/madwifi.h
index fe4b3e62af..80d32e1959 100644
--- a/package/iwinfo/src/include/iwinfo/api/madwifi.h
+++ b/package/iwinfo/src/include/iwinfo/api/madwifi.h
@@ -22,8 +22,10 @@
 #define _MADWIFI_H
 
 /* ieee80211.h */
-#define	IEEE80211_ADDR_LEN		6
-#define	IEEE80211_RATE_VAL		0x7f
+#define	IEEE80211_ADDR_LEN			6
+#define	IEEE80211_RATE_VAL			0x7f
+#define	IEEE80211_SEQ_SEQ_MASK		0xfff0
+#define	IEEE80211_SEQ_SEQ_SHIFT		4
 
 
 /* ieee80211_crypto.h */
diff --git a/package/iwinfo/src/include/iwinfo/api/nl80211.h b/package/iwinfo/src/include/iwinfo/api/nl80211.h
index 999e354218..d73dcb8e81 100644
--- a/package/iwinfo/src/include/iwinfo/api/nl80211.h
+++ b/package/iwinfo/src/include/iwinfo/api/nl80211.h
@@ -6,7 +6,7 @@
  * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
  * Copyright 2008 Michael Wu <flamingice@sourmilk.net>
  * Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com>
- * Copyright 2008 Michael Buesch <mb@bu3sch.de>
+ * Copyright 2008 Michael Buesch <m@bues.ch>
  * Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
  * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
  * Copyright 2008 Colin McCabe <colin@cozybit.com>
@@ -77,6 +77,39 @@
  */
 
 /**
+ * DOC: Virtual interface / concurrency capabilities
+ *
+ * Some devices are able to operate with virtual MACs, they can have
+ * more than one virtual interface. The capability handling for this
+ * is a bit complex though, as there may be a number of restrictions
+ * on the types of concurrency that are supported.
+ *
+ * To start with, each device supports the interface types listed in
+ * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
+ * types there no concurrency is implied.
+ *
+ * Once concurrency is desired, more attributes must be observed:
+ * To start with, since some interface types are purely managed in
+ * software, like the AP-VLAN type in mac80211 for example, there's
+ * an additional list of these, they can be added at any time and
+ * are only restricted by some semantic restrictions (e.g. AP-VLAN
+ * cannot be added without a corresponding AP interface). This list
+ * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
+ *
+ * Further, the list of supported combinations is exported. This is
+ * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
+ * it exports a list of "groups", and at any point in time the
+ * interfaces that are currently active must fall into any one of
+ * the advertised groups. Within each group, there are restrictions
+ * on the number of interfaces of different types that are supported
+ * and also the number of different channels, along with potentially
+ * some other restrictions. See &enum nl80211_if_combination_attrs.
+ *
+ * All together, these attributes define the concurrency of virtual
+ * interfaces that a given device supports.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -128,6 +161,13 @@
  * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface
  *	using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD,
  *	%NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes.
+ *	Following attributes are provided for drivers that generate full Beacon
+ *	and Probe Response frames internally: %NL80211_ATTR_SSID,
+ *	%NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
+ *	%NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
+ *	%NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
+ *	%NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP,
+ *	%NL80211_ATTR_IE_ASSOC_RESP.
  * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface,
  *	parameters are like for %NL80211_CMD_SET_BEACON.
  * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it
@@ -148,6 +188,10 @@
  * @NL80211_CMD_SET_MPATH:  Set mesh path attributes for mesh path to
  * 	destination %NL80211_ATTR_MAC on the interface identified by
  * 	%NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
+ *	%NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
+ * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
+ *	%NL80211_ATTR_MAC.
  * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
  *	the interface identified by %NL80211_ATTR_IFINDEX.
  * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
@@ -172,10 +216,10 @@
  * 	to the specified ISO/IEC 3166-1 alpha2 country code. The core will
  * 	store this as a valid request and then query userspace for it.
  *
- * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
+ * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
  *	interface identified by %NL80211_ATTR_IFINDEX
  *
- * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the
+ * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
  *      interface identified by %NL80211_ATTR_IFINDEX
  *
  * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
@@ -194,11 +238,36 @@
  *
  * @NL80211_CMD_GET_SCAN: get scan results
  * @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
+ *	%NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
+ *	probe requests at CCK rate or not.
  * @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
  *	NL80211_CMD_GET_SCAN and on the "scan" multicast group)
  * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
  *	partial scan results may be available
  *
+ * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
+ *	intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL.
+ *	Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
+ *	are passed, they are used in the probe requests.  For
+ *	broadcast, a broadcast SSID must be passed (ie. an empty
+ *	string).  If no SSID is passed, no probe requests are sent and
+ *	a passive scan is performed.  %NL80211_ATTR_SCAN_FREQUENCIES,
+ *	if passed, define which channels should be scanned; if not
+ *	passed, all channels allowed for the current regulatory domain
+ *	are used.  Extra IEs can also be passed from the userspace by
+ *	using the %NL80211_ATTR_IE attribute.
+ * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan.  Returns -ENOENT
+ *	if scheduled scan is not running.
+ * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
+ *	results available.
+ * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
+ *	stopped.  The driver may issue this event at any time during a
+ *	scheduled scan.  One reason for stopping the scan is if the hardware
+ *	does not support starting an association or a normal scan while running
+ *	a scheduled scan.  This event is also sent when the
+ *	%NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
+ *	is brought down while a scheduled scan was running.
+ *
  * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
  *      or noise level
  * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
@@ -358,11 +427,18 @@
  *	user space application). %NL80211_ATTR_FRAME is used to specify the
  *	frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
  *	optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on
- *	which channel the frame is to be transmitted or was received. This
- *	channel has to be the current channel (remain-on-channel or the
- *	operational channel). When called, this operation returns a cookie
- *	(%NL80211_ATTR_COOKIE) that will be included with the TX status event
- *	pertaining to the TX request.
+ *	which channel the frame is to be transmitted or was received. If this
+ *	channel is not the current channel (remain-on-channel or the
+ *	operational channel) the device will switch to the given channel and
+ *	transmit the frame, optionally waiting for a response for the time
+ *	specified using %NL80211_ATTR_DURATION. When called, this operation
+ *	returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
+ *	TX status event pertaining to the TX request.
+ *	%NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
+ *	management frames at CCK rate or not in 2GHz band.
+ * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
+ *	command may be used with the corresponding cookie to cancel the wait
+ *	time if it is known that it is no longer necessary.
  * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
  * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
  *	transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
@@ -389,11 +465,87 @@
  *
  * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
  *
+ * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
+ *	mesh config parameters may be given.
+ * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
+ *	network is determined by the network interface.
+ *
+ * @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame
+ *	notification. This event is used to indicate that an unprotected
+ *	deauthentication frame was dropped when MFP is in use.
+ * @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame
+ *	notification. This event is used to indicate that an unprotected
+ *	disassociation frame was dropped when MFP is in use.
+ *
+ * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
+ *      beacon or probe response from a compatible mesh peer.  This is only
+ *      sent while no station information (sta_info) exists for the new peer
+ *      candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set.  On
+ *      reception of this notification, userspace may decide to create a new
+ *      station (@NL80211_CMD_NEW_STATION).  To stop this notification from
+ *      reoccurring, the userspace authentication daemon may want to create the
+ *      new station with the AUTHENTICATED flag unset and maybe change it later
+ *      depending on the authentication result.
+ *
+ * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
+ * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
+ *	Since wireless is more complex than wired ethernet, it supports
+ *	various triggers. These triggers can be configured through this
+ *	command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
+ *	more background information, see
+ *	http://wireless.kernel.org/en/users/Documentation/WoWLAN.
+ *
+ * @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver
+ *	the necessary information for supporting GTK rekey offload. This
+ *	feature is typically used during WoWLAN. The configuration data
+ *	is contained in %NL80211_ATTR_REKEY_DATA (which is nested and
+ *	contains the data in sub-attributes). After rekeying happened,
+ *	this command may also be sent by the driver as an MLME event to
+ *	inform userspace of the new replay counter.
+ *
+ * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
+ *	of PMKSA caching dandidates.
+ *
+ * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
+ * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame.
+ *
+ * @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP
+ *	(or GO) interface (i.e. hostapd) to ask for unexpected frames to
+ *	implement sending deauth to stations that send unexpected class 3
+ *	frames. Also used as the event sent by the kernel when such a frame
+ *	is received.
+ *	For the event, the %NL80211_ATTR_MAC attribute carries the TA and
+ *	other attributes like the interface index are present.
+ *	If used as the command it must have an interface index and you can
+ *	only unsubscribe from the event by closing the socket. Subscription
+ *	is also for %NL80211_CMD_UNEXPECTED_4ADDR_FRAME events.
+ *
+ * @NL80211_CMD_UNEXPECTED_4ADDR_FRAME: Sent as an event indicating that the
+ *	associated station identified by %NL80211_ATTR_MAC sent a 4addr frame
+ *	and wasn't already in a 4-addr VLAN. The event will be sent similarly
+ *	to the %NL80211_CMD_UNEXPECTED_FRAME event, to the same listener.
+ *
+ * @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
+ *	by sending a null data frame to it and reporting when the frame is
+ *	acknowleged. This is used to allow timing out inactive clients. Uses
+ *	%NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
+ *	direct reply with an %NL80211_ATTR_COOKIE that is later used to match
+ *	up the event with the request. The event includes the same data and
+ *	has %NL80211_ATTR_ACK set if the frame was ACKed.
+ *
+ * @NL80211_CMD_REGISTER_BEACONS: Register this socket to receive beacons from
+ *	other BSSes when any interfaces are in AP mode. This helps implement
+ *	OLBC handling in hostapd. Beacons are reported in %NL80211_CMD_FRAME
+ *	messages. Note that per PHY only one application may register.
+ *
+ * @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether
+ *      No Acknowledgement Policy should be applied.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
 enum nl80211_commands {
-/* don't change the order or add anything inbetween, this is ABI! */
+/* don't change the order or add anything between, this is ABI! */
 	NL80211_CMD_UNSPEC,
 
 	NL80211_CMD_GET_WIPHY,		/* can dump */
@@ -431,8 +583,8 @@ enum nl80211_commands {
 	NL80211_CMD_SET_REG,
 	NL80211_CMD_REQ_SET_REG,
 
-	NL80211_CMD_GET_MESH_PARAMS,
-	NL80211_CMD_SET_MESH_PARAMS,
+	NL80211_CMD_GET_MESH_CONFIG,
+	NL80211_CMD_SET_MESH_CONFIG,
 
 	NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
 
@@ -493,6 +645,41 @@ enum nl80211_commands {
 	NL80211_CMD_SET_CHANNEL,
 	NL80211_CMD_SET_WDS_PEER,
 
+	NL80211_CMD_FRAME_WAIT_CANCEL,
+
+	NL80211_CMD_JOIN_MESH,
+	NL80211_CMD_LEAVE_MESH,
+
+	NL80211_CMD_UNPROT_DEAUTHENTICATE,
+	NL80211_CMD_UNPROT_DISASSOCIATE,
+
+	NL80211_CMD_NEW_PEER_CANDIDATE,
+
+	NL80211_CMD_GET_WOWLAN,
+	NL80211_CMD_SET_WOWLAN,
+
+	NL80211_CMD_START_SCHED_SCAN,
+	NL80211_CMD_STOP_SCHED_SCAN,
+	NL80211_CMD_SCHED_SCAN_RESULTS,
+	NL80211_CMD_SCHED_SCAN_STOPPED,
+
+	NL80211_CMD_SET_REKEY_OFFLOAD,
+
+	NL80211_CMD_PMKSA_CANDIDATE,
+
+	NL80211_CMD_TDLS_OPER,
+	NL80211_CMD_TDLS_MGMT,
+
+	NL80211_CMD_UNEXPECTED_FRAME,
+
+	NL80211_CMD_PROBE_CLIENT,
+
+	NL80211_CMD_REGISTER_BEACONS,
+
+	NL80211_CMD_UNEXPECTED_4ADDR_FRAME,
+
+	NL80211_CMD_SET_NOACK_MAP,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -513,6 +700,13 @@ enum nl80211_commands {
 #define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
 #define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
 
+#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
+
+/* source-level API compatibility */
+#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
+#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
+#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
+
 /**
  * enum nl80211_attrs - nl80211 netlink attributes
  *
@@ -583,7 +777,7 @@ enum nl80211_commands {
  *	consisting of a nested array.
  *
  * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
- * @NL80211_ATTR_PLINK_ACTION: action to perform on the mesh peer link.
+ * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link.
  * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
  * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
  * 	info given for %NL80211_CMD_GET_MPATH, nested attribute described at
@@ -628,8 +822,14 @@ enum nl80211_commands {
  *
  * @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with
  *	a single scan request, a wiphy attribute.
+ * @NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS: number of SSIDs you can
+ *	scan with a single scheduled scan request, a wiphy attribute.
  * @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements
  *	that can be added to a scan request
+ * @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information
+ *	elements that can be added to a scheduled scan request
+ * @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be
+ *	used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute.
  *
  * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
  * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
@@ -710,18 +910,20 @@ enum nl80211_commands {
  * @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT
  *	event (u16)
  * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating
- *	that protected APs should be used.
+ *	that protected APs should be used. This is also used with NEW_BEACON to
+ *	indicate that the BSS is to use protection.
  *
- * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT and ASSOCIATE to
- *	indicate which unicast key ciphers will be used with the connection
+ * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON
+ *	to indicate which unicast key ciphers will be used with the connection
  *	(an array of u32).
- * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT and ASSOCIATE to indicate
- *	which group key cipher will be used with the connection (a u32).
- * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT and ASSOCIATE to indicate
- *	which WPA version(s) the AP we want to associate with is using
+ * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
+ *	indicate which group key cipher will be used with the connection (a
+ *	u32).
+ * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
+ *	indicate which WPA version(s) the AP we want to associate with is using
  *	(a u32 with flags from &enum nl80211_wpa_versions).
- * @NL80211_ATTR_AKM_SUITES: Used with CONNECT and ASSOCIATE to indicate
- *	which key management algorithm(s) to use (an array of u32).
+ * @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
+ *	indicate which key management algorithm(s) to use (an array of u32).
  *
  * @NL80211_ATTR_REQ_IE: (Re)association request information elements as
  *	sent out by the card, for ROAM and successful CONNECT events.
@@ -758,6 +960,9 @@ enum nl80211_commands {
  *	cache, a wiphy attribute.
  *
  * @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32.
+ * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
+ *	specifies the maximum duration that can be requested with the
+ *	remain-on-channel operation, in milliseconds, u32.
  *
  * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
  *
@@ -804,13 +1009,195 @@ enum nl80211_commands {
  * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
  *	means support for per-station GTKs.
  *
+ * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
+ *	This can be used to mask out antennas which are not attached or should
+ *	not be used for transmitting. If an antenna is not selected in this
+ *	bitmap the hardware is not allowed to transmit on this antenna.
+ *
+ *	Each bit represents one antenna, starting with antenna 1 at the first
+ *	bit. Depending on which antennas are selected in the bitmap, 802.11n
+ *	drivers can derive which chainmasks to use (if all antennas belonging to
+ *	a particular chain are disabled this chain should be disabled) and if
+ *	a chain has diversity antennas wether diversity should be used or not.
+ *	HT capabilities (STBC, TX Beamforming, Antenna selection) can be
+ *	derived from the available chains after applying the antenna mask.
+ *	Non-802.11n drivers can derive wether to use diversity or not.
+ *	Drivers may reject configurations or RX/TX mask combinations they cannot
+ *	support by returning -EINVAL.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
+ *	This can be used to mask out antennas which are not attached or should
+ *	not be used for receiving. If an antenna is not selected in this bitmap
+ *	the hardware should not be configured to receive on this antenna.
+ *	For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available
+ *	for configuration as TX antennas via the above parameters.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available
+ *	for configuration as RX antennas via the above parameters.
+ *
  * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
  *
+ * @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be
+ *	transmitted on another channel when the channel given doesn't match
+ *	the current channel. If the current channel doesn't match and this
+ *	flag isn't set, the frame will be rejected. This is also used as an
+ *	nl80211 capability flag.
+ *
+ * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16)
+ *
+ * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
+ *	attributes, specifying what a key should be set as default as.
+ *	See &enum nl80211_key_default_types.
+ *
+ * @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters.  These cannot be
+ *	changed once the mesh is active.
+ * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
+ *	containing attributes from &enum nl80211_meshconf_params.
+ * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
+ *	allows auth frames in a mesh to be passed to userspace for processing via
+ *	the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
+ * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as
+ *	defined in &enum nl80211_plink_state. Used when userspace is
+ *	driving the peer link management state machine.
+ *	@NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled.
+ *
+ * @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy
+ *	capabilities, the supported WoWLAN triggers
+ * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to
+ *	indicate which WoW triggers should be enabled. This is also
+ *	used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN
+ *	triggers.
+
+ * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
+ *	cycles, in msecs.
+
+ * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more
+ *	sets of attributes to match during scheduled scans.  Only BSSs
+ *	that match any of the sets will be reported.  These are
+ *	pass-thru filter rules.
+ *	For a match to succeed, the BSS must match all attributes of a
+ *	set.  Since not every hardware supports matching all types of
+ *	attributes, there is no guarantee that the reported BSSs are
+ *	fully complying with the match sets and userspace needs to be
+ *	able to ignore them by itself.
+ *	Thus, the implementation is somewhat hardware-dependent, but
+ *	this is only an optimization and the userspace application
+ *	needs to handle all the non-filtered results anyway.
+ *	If the match attributes don't make sense when combined with
+ *	the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID
+ *	is included in the probe request, but the match attributes
+ *	will never let it go through), -EINVAL may be returned.
+ *	If ommited, no filtering is done.
+ *
+ * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
+ *	interface combinations. In each nested item, it contains attributes
+ *	defined in &enum nl80211_if_combination_attrs.
+ * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like
+ *	%NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that
+ *	are managed in software: interfaces of these types aren't subject to
+ *	any restrictions in their number or combinations.
+ *
+ * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information
+ *	necessary for GTK rekeying in the device, see &enum nl80211_rekey_data.
+ *
+ * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan,
+ *	nested array attribute containing an entry for each band, with the entry
+ *	being a list of supported rates as defined by IEEE 802.11 7.3.2.2 but
+ *	without the length restriction (at most %NL80211_MAX_SUPP_RATES).
+ *
+ * @NL80211_ATTR_HIDDEN_SSID: indicates whether SSID is to be hidden from Beacon
+ *	and Probe Response (when response to wildcard Probe Request); see
+ *	&enum nl80211_hidden_ssid, represented as a u32
+ *
+ * @NL80211_ATTR_IE_PROBE_RESP: Information element(s) for Probe Response frame.
+ *	This is used with %NL80211_CMD_NEW_BEACON and %NL80211_CMD_SET_BEACON to
+ *	provide extra IEs (e.g., WPS/P2P IE) into Probe Response frames when the
+ *	driver (or firmware) replies to Probe Request frames.
+ * @NL80211_ATTR_IE_ASSOC_RESP: Information element(s) for (Re)Association
+ *	Response frames. This is used with %NL80211_CMD_NEW_BEACON and
+ *	%NL80211_CMD_SET_BEACON to provide extra IEs (e.g., WPS/P2P IE) into
+ *	(Re)Association Response frames when the driver (or firmware) replies to
+ *	(Re)Association Request frames.
+ *
+ * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration
+ *	of the station, see &enum nl80211_sta_wme_attr.
+ * @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working
+ *	as AP.
+ *
+ * @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of
+ *	roaming to another AP in the same ESS if the signal lever is low.
+ *
+ * @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching
+ *	candidate information, see &enum nl80211_pmksa_candidate_attr.
+ *
+ * @NL80211_ATTR_TX_NO_CCK_RATE: Indicates whether to use CCK rate or not
+ *	for management frames transmission. In order to avoid p2p probe/action
+ *	frames are being transmitted at CCK rate in 2GHz band, the user space
+ *	applications use this attribute.
+ *	This attribute is used with %NL80211_CMD_TRIGGER_SCAN and
+ *	%NL80211_CMD_FRAME commands.
+ *
+ * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup
+ *	request, link setup confirm, link teardown, etc.). Values are
+ *	described in the TDLS (802.11z) specification.
+ * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a
+ *	TDLS conversation between two devices.
+ * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see
+ *	&enum nl80211_tdls_operation, represented as a u8.
+ * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate
+ *	as a TDLS peer sta.
+ * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown
+ *	procedures should be performed by sending TDLS packets via
+ *	%NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be
+ *	used for asking the driver to perform a TDLS operation.
+ *
+ * @NL80211_ATTR_DEVICE_AP_SME: This u32 attribute may be listed for devices
+ *	that have AP support to indicate that they have the AP SME integrated
+ *	with support for the features listed in this attribute, see
+ *	&enum nl80211_ap_sme_features.
+ *
+ * @NL80211_ATTR_DONT_WAIT_FOR_ACK: Used with %NL80211_CMD_FRAME, this tells
+ *	the driver to not wait for an acknowledgement. Note that due to this,
+ *	it will also not give a status callback nor return a cookie. This is
+ *	mostly useful for probe responses to save airtime.
+ *
+ * @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from
+ *	&enum nl80211_feature_flags and is advertised in wiphy information.
+ * @NL80211_ATTR_PROBE_RESP_OFFLOAD: Indicates that the HW responds to probe
+ *
+ *	requests while operating in AP-mode.
+ *	This attribute holds a bitmap of the supported protocols for
+ *	offloading (see &enum nl80211_probe_resp_offload_support_attr).
+ *
+ * @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire
+ *	probe-response frame. The DA field in the 802.11 header is zero-ed out,
+ *	to be filled by the FW.
+ * @NL80211_ATTR_DISABLE_HT:  Force HT capable interfaces to disable
+ *      this feature.  Currently, only supported in mac80211 drivers.
+ * @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the
+ *      ATTR_HT_CAPABILITY to which attention should be paid.
+ *      Currently, only mac80211 NICs support this feature.
+ *      The values that may be configured are:
+ *       MCS rates, MAX-AMSDU, HT-20-40 and HT_CAP_SGI_40
+ *       AMPDU density and AMPDU factor.
+ *      All values are treated as suggestions and may be ignored
+ *      by the driver as required.  The actual values may be seen in
+ *      the station debugfs ht_caps file.
+ *
+ * @NL80211_ATTR_DFS_REGION: region for regulatory rules which this country
+ *    abides to when initiating radiation on DFS channels. A country maps
+ *    to one DFS region.
+ *
+ * @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of
+ *      up to 16 TIDs.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_attrs {
-/* don't change the order or add anything inbetween, this is ABI! */
+/* don't change the order or add anything between, this is ABI! */
 	NL80211_ATTR_UNSPEC,
 
 	NL80211_ATTR_WIPHY,
@@ -860,7 +1247,7 @@ enum nl80211_attrs {
 	NL80211_ATTR_REG_ALPHA2,
 	NL80211_ATTR_REG_RULES,
 
-	NL80211_ATTR_MESH_PARAMS,
+	NL80211_ATTR_MESH_CONFIG,
 
 	NL80211_ATTR_BSS_BASIC_RATES,
 
@@ -975,8 +1362,82 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_SUPPORT_IBSS_RSN,
 
+	NL80211_ATTR_WIPHY_ANTENNA_TX,
+	NL80211_ATTR_WIPHY_ANTENNA_RX,
+
 	NL80211_ATTR_MCAST_RATE,
 
+	NL80211_ATTR_OFFCHANNEL_TX_OK,
+
+	NL80211_ATTR_BSS_HT_OPMODE,
+
+	NL80211_ATTR_KEY_DEFAULT_TYPES,
+
+	NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
+
+	NL80211_ATTR_MESH_SETUP,
+
+	NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX,
+	NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX,
+
+	NL80211_ATTR_SUPPORT_MESH_AUTH,
+	NL80211_ATTR_STA_PLINK_STATE,
+
+	NL80211_ATTR_WOWLAN_TRIGGERS,
+	NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED,
+
+	NL80211_ATTR_SCHED_SCAN_INTERVAL,
+
+	NL80211_ATTR_INTERFACE_COMBINATIONS,
+	NL80211_ATTR_SOFTWARE_IFTYPES,
+
+	NL80211_ATTR_REKEY_DATA,
+
+	NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS,
+	NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN,
+
+	NL80211_ATTR_SCAN_SUPP_RATES,
+
+	NL80211_ATTR_HIDDEN_SSID,
+
+	NL80211_ATTR_IE_PROBE_RESP,
+	NL80211_ATTR_IE_ASSOC_RESP,
+
+	NL80211_ATTR_STA_WME,
+	NL80211_ATTR_SUPPORT_AP_UAPSD,
+
+	NL80211_ATTR_ROAM_SUPPORT,
+
+	NL80211_ATTR_SCHED_SCAN_MATCH,
+	NL80211_ATTR_MAX_MATCH_SETS,
+
+	NL80211_ATTR_PMKSA_CANDIDATE,
+
+	NL80211_ATTR_TX_NO_CCK_RATE,
+
+	NL80211_ATTR_TDLS_ACTION,
+	NL80211_ATTR_TDLS_DIALOG_TOKEN,
+	NL80211_ATTR_TDLS_OPERATION,
+	NL80211_ATTR_TDLS_SUPPORT,
+	NL80211_ATTR_TDLS_EXTERNAL_SETUP,
+
+	NL80211_ATTR_DEVICE_AP_SME,
+
+	NL80211_ATTR_DONT_WAIT_FOR_ACK,
+
+	NL80211_ATTR_FEATURE_FLAGS,
+
+	NL80211_ATTR_PROBE_RESP_OFFLOAD,
+
+	NL80211_ATTR_PROBE_RESP,
+
+	NL80211_ATTR_DFS_REGION,
+
+	NL80211_ATTR_DISABLE_HT,
+	NL80211_ATTR_HT_CAPABILITY_MASK,
+
+	NL80211_ATTR_NOACK_MAP,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -985,6 +1446,7 @@ enum nl80211_attrs {
 
 /* source-level API compatibility */
 #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
+#define	NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
 
 /*
  * Allow user space programs to use #ifdef on new attributes by defining them
@@ -1010,8 +1472,10 @@ enum nl80211_attrs {
 #define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES
 #define NL80211_ATTR_KEY NL80211_ATTR_KEY
 #define NL80211_ATTR_KEYS NL80211_ATTR_KEYS
+#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
 
 #define NL80211_MAX_SUPP_RATES			32
+#define NL80211_MAX_SUPP_HT_RATES		77
 #define NL80211_MAX_SUPP_REG_RULES		32
 #define NL80211_TKIP_DATA_OFFSET_ENCR_KEY	0
 #define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY	16
@@ -1028,7 +1492,9 @@ enum nl80211_attrs {
  * @NL80211_IFTYPE_ADHOC: independent BSS member
  * @NL80211_IFTYPE_STATION: managed BSS member
  * @NL80211_IFTYPE_AP: access point
- * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points
+ * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces
+ *	are a bit special in that they must always be tied to a pre-existing
+ *	AP type interface.
  * @NL80211_IFTYPE_WDS: wireless distribution interface
  * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
  * @NL80211_IFTYPE_MESH_POINT: mesh point
@@ -1070,6 +1536,12 @@ enum nl80211_iftype {
  *	with short barker preamble
  * @NL80211_STA_FLAG_WME: station is WME/QoS capable
  * @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
+ * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should
+ *	only be used in managed mode (even in the flags mask). Note that the
+ *	flag can't be changed, it is only valid while adding a station, and
+ *	attempts to change it will silently be ignored (rather than rejected
+ *	as errors.)
  * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
  * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
@@ -1079,6 +1551,8 @@ enum nl80211_sta_flags {
 	NL80211_STA_FLAG_SHORT_PREAMBLE,
 	NL80211_STA_FLAG_WME,
 	NL80211_STA_FLAG_MFP,
+	NL80211_STA_FLAG_AUTHENTICATED,
+	NL80211_STA_FLAG_TDLS_PEER,
 
 	/* keep last */
 	__NL80211_STA_FLAG_AFTER_LAST,
@@ -1124,6 +1598,36 @@ enum nl80211_rate_info {
 };
 
 /**
+ * enum nl80211_sta_bss_param - BSS information collected by STA
+ *
+ * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
+ * when getting information about the bitrate of a station.
+ *
+ * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
+ * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag)
+ * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE:  whether short preamble is enabled
+ *	(flag)
+ * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME:  whether short slot time is enabled
+ *	(flag)
+ * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8)
+ * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16)
+ * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined
+ * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use
+ */
+enum nl80211_sta_bss_param {
+	__NL80211_STA_BSS_PARAM_INVALID,
+	NL80211_STA_BSS_PARAM_CTS_PROT,
+	NL80211_STA_BSS_PARAM_SHORT_PREAMBLE,
+	NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME,
+	NL80211_STA_BSS_PARAM_DTIM_PERIOD,
+	NL80211_STA_BSS_PARAM_BEACON_INTERVAL,
+
+	/* keep last */
+	__NL80211_STA_BSS_PARAM_AFTER_LAST,
+	NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_sta_info - station information
  *
  * These attribute types are used with %NL80211_ATTR_STA_INFO
@@ -1133,16 +1637,30 @@ enum nl80211_rate_info {
  * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
  * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station)
  * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
- * @__NL80211_STA_INFO_AFTER_LAST: internal
- * @NL80211_STA_INFO_MAX: highest possible station info attribute
  * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
  * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
- * 	containing info as possible, see &enum nl80211_sta_info_txrate.
+ * 	containing info as possible, see &enum nl80211_rate_info
  * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
  * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
  *	station)
  * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
  * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
+ * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
+ * @NL80211_STA_INFO_LLID: the station's mesh LLID
+ * @NL80211_STA_INFO_PLID: the station's mesh PLID
+ * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
+ *	(see %enum nl80211_plink_state)
+ * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested
+ *	attribute, like NL80211_STA_INFO_TX_BITRATE.
+ * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
+ *     containing info as possible, see &enum nl80211_sta_bss_param
+ * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
+ * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
+ * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
+ * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
+ * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
+ * @__NL80211_STA_INFO_AFTER_LAST: internal
+ * @NL80211_STA_INFO_MAX: highest possible station info attribute
  */
 enum nl80211_sta_info {
 	__NL80211_STA_INFO_INVALID,
@@ -1158,6 +1676,14 @@ enum nl80211_sta_info {
 	NL80211_STA_INFO_TX_PACKETS,
 	NL80211_STA_INFO_TX_RETRIES,
 	NL80211_STA_INFO_TX_FAILED,
+	NL80211_STA_INFO_SIGNAL_AVG,
+	NL80211_STA_INFO_RX_BITRATE,
+	NL80211_STA_INFO_BSS_PARAM,
+	NL80211_STA_INFO_CONNECTED_TIME,
+	NL80211_STA_INFO_STA_FLAGS,
+	NL80211_STA_INFO_BEACON_LOSS,
+	NL80211_STA_INFO_CHAIN_SIGNAL,
+	NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
 
 	/* keep last */
 	__NL80211_STA_INFO_AFTER_LAST,
@@ -1311,7 +1837,11 @@ enum nl80211_bitrate_attr {
  * 	wireless core it thinks its knows the regulatory domain we should be in.
  * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
  * 	802.11 country information element with regulatory information it
- * 	thinks we should consider.
+ * 	thinks we should consider. cfg80211 only processes the country
+ *	code from the IE, and relies on the regulatory domain information
+ *	structure passed by userspace (CRDA) from our wireless-regdb.
+ *	If a channel is enabled but the country code indicates it should
+ *	be disabled we disable the channel and re-enable it upon disassociation.
  */
 enum nl80211_reg_initiator {
 	NL80211_REGDOM_SET_BY_CORE,
@@ -1383,6 +1913,26 @@ enum nl80211_reg_rule_attr {
 };
 
 /**
+ * enum nl80211_sched_scan_match_attr - scheduled scan match attributes
+ * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved
+ * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching,
+ * only report BSS with matching SSID.
+ * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
+ *	attribute number currently defined
+ * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
+ */
+enum nl80211_sched_scan_match_attr {
+	__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID,
+
+	NL80211_ATTR_SCHED_SCAN_MATCH_SSID,
+
+	/* keep last */
+	__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
+	NL80211_SCHED_SCAN_MATCH_ATTR_MAX =
+		__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_reg_rule_flags - regulatory rule flags
  *
  * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed
@@ -1408,6 +1958,21 @@ enum nl80211_reg_rule_flags {
 };
 
 /**
+ * enum nl80211_dfs_regions - regulatory DFS regions
+ *
+ * @NL80211_DFS_UNSET: Country has no DFS master region specified
+ * @NL80211_DFS_FCC_: Country follows DFS master rules from FCC
+ * @NL80211_DFS_FCC_: Country follows DFS master rules from ETSI
+ * @NL80211_DFS_JP_: Country follows DFS master rules from JP/MKK/Telec
+ */
+enum nl80211_dfs_regions {
+	NL80211_DFS_UNSET	= 0,
+	NL80211_DFS_FCC		= 1,
+	NL80211_DFS_ETSI	= 2,
+	NL80211_DFS_JP		= 3,
+};
+
+/**
  * enum nl80211_survey_info - survey information
  *
  * These attribute types are used with %NL80211_ATTR_SURVEY_INFO
@@ -1480,14 +2045,15 @@ enum nl80211_mntr_flags {
 /**
  * enum nl80211_meshconf_params - mesh configuration parameters
  *
- * Mesh configuration parameters
+ * Mesh configuration parameters. These can be changed while the mesh is
+ * active.
  *
  * @__NL80211_MESHCONF_INVALID: internal use
  *
  * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
  * millisecond units, used by the Peer Link Open message
  *
- * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the inital confirm timeout, in
+ * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in
  * millisecond units, used by the peer link management to close a peer link
  *
  * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
@@ -1527,7 +2093,24 @@ enum nl80211_mntr_flags {
  * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
  * that it takes for an HWMP information element to propagate across the mesh
  *
- * @NL80211_MESHCONF_ROOTMODE: whether root mode is enabled or not
+ * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
+ *
+ * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
+ * source mesh point for path selection elements.
+ *
+ * @NL80211_MESHCONF_HWMP_RANN_INTERVAL:  The interval of time (in TUs) between
+ * root announcements are transmitted.
+ *
+ * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has
+ * access to a broader network beyond the MBSS.  This is done via Root
+ * Announcement frames.
+ *
+ * @NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL: The minimum interval of time (in
+ * TUs) during which a mesh STA can send only one Action frame containing a
+ * PERR element.
+ *
+ * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
+ * or forwarding entity (default is TRUE - forwarding entity)
  *
  * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
  *
@@ -1549,6 +2132,11 @@ enum nl80211_meshconf_params {
 	NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL,
 	NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME,
 	NL80211_MESHCONF_HWMP_ROOTMODE,
+	NL80211_MESHCONF_ELEMENT_TTL,
+	NL80211_MESHCONF_HWMP_RANN_INTERVAL,
+	NL80211_MESHCONF_GATE_ANNOUNCEMENTS,
+	NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL,
+	NL80211_MESHCONF_FORWARDING,
 
 	/* keep last */
 	__NL80211_MESHCONF_ATTR_AFTER_LAST,
@@ -1556,6 +2144,54 @@ enum nl80211_meshconf_params {
 };
 
 /**
+ * enum nl80211_mesh_setup_params - mesh setup parameters
+ *
+ * Mesh setup parameters.  These are used to start/join a mesh and cannot be
+ * changed while the mesh is active.
+ *
+ * @__NL80211_MESH_SETUP_INVALID: Internal use
+ *
+ * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a
+ * vendor specific path selection algorithm or disable it to use the default
+ * HWMP.
+ *
+ * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a
+ * vendor specific path metric or disable it to use the default Airtime
+ * metric.
+ *
+ * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
+ * robust security network ie, or a vendor specific information element that
+ * vendors will use to identify the path selection methods and metrics in use.
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
+ * daemon will be authenticating mesh candidates.
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication
+ * daemon will be securing peer link frames.  AMPE is a secured version of Mesh
+ * Peering Management (MPM) and is implemented with the assistance of a
+ * userspace daemon.  When this flag is set, the kernel will send peer
+ * management frames to a userspace daemon that will implement AMPE
+ * functionality (security capabilities selection, key confirmation, and key
+ * management).  When the flag is unset (default), the kernel can autonomously
+ * complete (unsecured) mesh peering without the need of a userspace daemon.
+ *
+ * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
+ * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
+ */
+enum nl80211_mesh_setup_params {
+	__NL80211_MESH_SETUP_INVALID,
+	NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL,
+	NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC,
+	NL80211_MESH_SETUP_IE,
+	NL80211_MESH_SETUP_USERSPACE_AUTH,
+	NL80211_MESH_SETUP_USERSPACE_AMPE,
+
+	/* keep last */
+	__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
+	NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_txq_attr - TX queue parameter attributes
  * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
  * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*)
@@ -1713,6 +2349,23 @@ enum nl80211_wpa_versions {
 };
 
 /**
+ * enum nl80211_key_default_types - key default types
+ * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid
+ * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default
+ *	unicast key
+ * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default
+ *	multicast key
+ * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types
+ */
+enum nl80211_key_default_types {
+	__NL80211_KEY_DEFAULT_TYPE_INVALID,
+	NL80211_KEY_DEFAULT_TYPE_UNICAST,
+	NL80211_KEY_DEFAULT_TYPE_MULTICAST,
+
+	NUM_NL80211_KEY_DEFAULT_TYPES
+};
+
+/**
  * enum nl80211_key_attributes - key attributes
  * @__NL80211_KEY_INVALID: invalid
  * @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of
@@ -1728,6 +2381,9 @@ enum nl80211_wpa_versions {
  * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
  *	specified the default depends on whether a MAC address was
  *	given with the command using the key or not (u32)
+ * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
+ *	attributes, specifying what a key should be set as default as.
+ *	See &enum nl80211_key_default_types.
  * @__NL80211_KEY_AFTER_LAST: internal
  * @NL80211_KEY_MAX: highest key attribute
  */
@@ -1740,6 +2396,7 @@ enum nl80211_key_attributes {
 	NL80211_KEY_DEFAULT,
 	NL80211_KEY_DEFAULT_MGMT,
 	NL80211_KEY_TYPE,
+	NL80211_KEY_DEFAULT_TYPES,
 
 	/* keep last */
 	__NL80211_KEY_AFTER_LAST,
@@ -1753,12 +2410,15 @@ enum nl80211_key_attributes {
  *	in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
  *	1 = 500 kbps) but without the IE length restriction (at most
  *	%NL80211_MAX_SUPP_RATES in a single array).
+ * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection
+ *	in an array of MCS numbers.
  * @__NL80211_TXRATE_AFTER_LAST: internal
  * @NL80211_TXRATE_MAX: highest TX rate attribute
  */
 enum nl80211_tx_rate_attributes {
 	__NL80211_TXRATE_INVALID,
 	NL80211_TXRATE_LEGACY,
+	NL80211_TXRATE_MCS,
 
 	/* keep last */
 	__NL80211_TXRATE_AFTER_LAST,
@@ -1790,6 +2450,8 @@ enum nl80211_ps_state {
  *	the minimum amount the RSSI level must change after an event before a
  *	new event may be issued (to reduce effects of RSSI oscillation).
  * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event
+ * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many
+ *	consecutive packets were not acknowledged by the peer
  * @__NL80211_ATTR_CQM_AFTER_LAST: internal
  * @NL80211_ATTR_CQM_MAX: highest key attribute
  */
@@ -1798,6 +2460,7 @@ enum nl80211_attr_cqm {
 	NL80211_ATTR_CQM_RSSI_THOLD,
 	NL80211_ATTR_CQM_RSSI_HYST,
 	NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT,
+	NL80211_ATTR_CQM_PKT_LOSS_EVENT,
 
 	/* keep last */
 	__NL80211_ATTR_CQM_AFTER_LAST,
@@ -1829,4 +2492,343 @@ enum nl80211_tx_power_setting {
 	NL80211_TX_POWER_FIXED,
 };
 
+/**
+ * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
+ * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ *	a zero bit are ignored
+ * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ *	a bit for each byte in the pattern. The lowest-order bit corresponds
+ *	to the first byte of the pattern, but the bytes of the pattern are
+ *	in a little-endian-like format, i.e. the 9th byte of the pattern
+ *	corresponds to the lowest-order bit in the second byte of the mask.
+ *	For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where
+ *	xx indicates "don't care") would be represented by a pattern of
+ *	twelve zero bytes, and a mask of "0xed,0x07".
+ *	Note that the pattern matching is done as though frames were not
+ *	802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
+ *	first (including SNAP header unpacking) and then matched.
+ * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
+ * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ */
+enum nl80211_wowlan_packet_pattern_attr {
+	__NL80211_WOWLAN_PKTPAT_INVALID,
+	NL80211_WOWLAN_PKTPAT_MASK,
+	NL80211_WOWLAN_PKTPAT_PATTERN,
+
+	NUM_NL80211_WOWLAN_PKTPAT,
+	MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+};
+
+/**
+ * struct nl80211_wowlan_pattern_support - pattern support information
+ * @max_patterns: maximum number of patterns supported
+ * @min_pattern_len: minimum length of each pattern
+ * @max_pattern_len: maximum length of each pattern
+ *
+ * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
+ * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
+ * capability information given by the kernel to userspace.
+ */
+struct nl80211_wowlan_pattern_support {
+	__u32 max_patterns;
+	__u32 min_pattern_len;
+	__u32 max_pattern_len;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
+ * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
+ * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put
+ *	the chip into a special state -- works best with chips that have
+ *	support for low-power operation already (flag)
+ * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect
+ *	is detected is implementation-specific (flag)
+ * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed
+ *	by 16 repetitions of MAC addr, anywhere in payload) (flag)
+ * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns
+ *	which are passed in an array of nested attributes, each nested attribute
+ *	defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern.
+ *	Each pattern defines a wakeup packet. The matching is done on the MSDU,
+ *	i.e. as though the packet was an 802.3 packet, so the pattern matching
+ *	is done after the packet is converted to the MSDU.
+ *
+ *	In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
+ *	carrying a &struct nl80211_wowlan_pattern_support.
+ * @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be
+ *	used when setting, used only to indicate that GTK rekeying is supported
+ *	by the device (flag)
+ * @NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE: wake up on GTK rekey failure (if
+ *	done by the device) (flag)
+ * @NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST: wake up on EAP Identity Request
+ *	packet (flag)
+ * @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag)
+ * @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released
+ *	(on devices that have rfkill in the device) (flag)
+ * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
+ * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
+ */
+enum nl80211_wowlan_triggers {
+	__NL80211_WOWLAN_TRIG_INVALID,
+	NL80211_WOWLAN_TRIG_ANY,
+	NL80211_WOWLAN_TRIG_DISCONNECT,
+	NL80211_WOWLAN_TRIG_MAGIC_PKT,
+	NL80211_WOWLAN_TRIG_PKT_PATTERN,
+	NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED,
+	NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE,
+	NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST,
+	NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE,
+	NL80211_WOWLAN_TRIG_RFKILL_RELEASE,
+
+	/* keep last */
+	NUM_NL80211_WOWLAN_TRIG,
+	MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
+};
+
+/**
+ * enum nl80211_iface_limit_attrs - limit attributes
+ * @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
+ * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that
+ *	can be chosen from this set of interface types (u32)
+ * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a
+ *	flag attribute for each interface type in this set
+ * @NUM_NL80211_IFACE_LIMIT: number of attributes
+ * @MAX_NL80211_IFACE_LIMIT: highest attribute number
+ */
+enum nl80211_iface_limit_attrs {
+	NL80211_IFACE_LIMIT_UNSPEC,
+	NL80211_IFACE_LIMIT_MAX,
+	NL80211_IFACE_LIMIT_TYPES,
+
+	/* keep last */
+	NUM_NL80211_IFACE_LIMIT,
+	MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1
+};
+
+/**
+ * enum nl80211_if_combination_attrs -- interface combination attributes
+ *
+ * @NL80211_IFACE_COMB_UNSPEC: (reserved)
+ * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits
+ *	for given interface types, see &enum nl80211_iface_limit_attrs.
+ * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of
+ *	interfaces that can be created in this group. This number doesn't
+ *	apply to interfaces purely managed in software, which are listed
+ *	in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE.
+ * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that
+ *	beacon intervals within this group must be all the same even for
+ *	infrastructure and AP/GO combinations, i.e. the GO(s) must adopt
+ *	the infrastructure network's beacon interval.
+ * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
+ *	different channels may be used within this group.
+ * @NUM_NL80211_IFACE_COMB: number of attributes
+ * @MAX_NL80211_IFACE_COMB: highest attribute number
+ *
+ * Examples:
+ *	limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2
+ *	=> allows an AP and a STA that must match BIs
+ *
+ *	numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8
+ *	=> allows 8 of AP/GO
+ *
+ *	numbers = [ #{STA} <= 2 ], channels = 2, max = 2
+ *	=> allows two STAs on different channels
+ *
+ *	numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
+ *	=> allows a STA plus three P2P interfaces
+ *
+ * The list of these four possiblities could completely be contained
+ * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
+ * that any of these groups must match.
+ *
+ * "Combinations" of just a single interface will not be listed here,
+ * a single interface of any valid interface type is assumed to always
+ * be possible by itself. This means that implicitly, for each valid
+ * interface type, the following group always exists:
+ *	numbers = [ #{<type>} <= 1 ], channels = 1, max = 1
+ */
+enum nl80211_if_combination_attrs {
+	NL80211_IFACE_COMB_UNSPEC,
+	NL80211_IFACE_COMB_LIMITS,
+	NL80211_IFACE_COMB_MAXNUM,
+	NL80211_IFACE_COMB_STA_AP_BI_MATCH,
+	NL80211_IFACE_COMB_NUM_CHANNELS,
+
+	/* keep last */
+	NUM_NL80211_IFACE_COMB,
+	MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1
+};
+
+
+/**
+ * enum nl80211_plink_state - state of a mesh peer link finite state machine
+ *
+ * @NL80211_PLINK_LISTEN: initial state, considered the implicit
+ *	state of non existant mesh peer links
+ * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
+ *	this mesh peer
+ * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
+ *	from this mesh peer
+ * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been
+ *	received from this mesh peer
+ * @NL80211_PLINK_ESTAB: mesh peer link is established
+ * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled
+ * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh
+ *	plink are discarded
+ * @NUM_NL80211_PLINK_STATES: number of peer link states
+ * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states
+ */
+enum nl80211_plink_state {
+	NL80211_PLINK_LISTEN,
+	NL80211_PLINK_OPN_SNT,
+	NL80211_PLINK_OPN_RCVD,
+	NL80211_PLINK_CNF_RCVD,
+	NL80211_PLINK_ESTAB,
+	NL80211_PLINK_HOLDING,
+	NL80211_PLINK_BLOCKED,
+
+	/* keep last */
+	NUM_NL80211_PLINK_STATES,
+	MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
+};
+
+#define NL80211_KCK_LEN			16
+#define NL80211_KEK_LEN			16
+#define NL80211_REPLAY_CTR_LEN		8
+
+/**
+ * enum nl80211_rekey_data - attributes for GTK rekey offload
+ * @__NL80211_REKEY_DATA_INVALID: invalid number for nested attributes
+ * @NL80211_REKEY_DATA_KEK: key encryption key (binary)
+ * @NL80211_REKEY_DATA_KCK: key confirmation key (binary)
+ * @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary)
+ * @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal)
+ * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
+ */
+enum nl80211_rekey_data {
+	__NL80211_REKEY_DATA_INVALID,
+	NL80211_REKEY_DATA_KEK,
+	NL80211_REKEY_DATA_KCK,
+	NL80211_REKEY_DATA_REPLAY_CTR,
+
+	/* keep last */
+	NUM_NL80211_REKEY_DATA,
+	MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1
+};
+
+/**
+ * enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID
+ * @NL80211_HIDDEN_SSID_NOT_IN_USE: do not hide SSID (i.e., broadcast it in
+ *	Beacon frames)
+ * @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element
+ *	in Beacon frames
+ * @NL80211_HIDDEN_SSID_ZERO_CONTENTS: hide SSID by using correct length of SSID
+ *	element in Beacon frames but zero out each byte in the SSID
+ */
+enum nl80211_hidden_ssid {
+	NL80211_HIDDEN_SSID_NOT_IN_USE,
+	NL80211_HIDDEN_SSID_ZERO_LEN,
+	NL80211_HIDDEN_SSID_ZERO_CONTENTS
+};
+
+/**
+ * enum nl80211_sta_wme_attr - station WME attributes
+ * @__NL80211_STA_WME_INVALID: invalid number for nested attribute
+ * @NL80211_STA_WME_UAPSD_QUEUES: bitmap of uapsd queues. the format
+ *	is the same as the AC bitmap in the QoS info field.
+ * @NL80211_STA_WME_MAX_SP: max service period. the format is the same
+ *	as the MAX_SP field in the QoS info field (but already shifted down).
+ * @__NL80211_STA_WME_AFTER_LAST: internal
+ * @NL80211_STA_WME_MAX: highest station WME attribute
+ */
+enum nl80211_sta_wme_attr {
+	__NL80211_STA_WME_INVALID,
+	NL80211_STA_WME_UAPSD_QUEUES,
+	NL80211_STA_WME_MAX_SP,
+
+	/* keep last */
+	__NL80211_STA_WME_AFTER_LAST,
+	NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates
+ * @__NL80211_PMKSA_CANDIDATE_INVALID: invalid number for nested attributes
+ * @NL80211_PMKSA_CANDIDATE_INDEX: candidate index (u32; the smaller, the higher
+ *	priority)
+ * @NL80211_PMKSA_CANDIDATE_BSSID: candidate BSSID (6 octets)
+ * @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag)
+ * @NUM_NL80211_PMKSA_CANDIDATE: number of PMKSA caching candidate attributes
+ *	(internal)
+ * @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute
+ *	(internal)
+ */
+enum nl80211_pmksa_candidate_attr {
+	__NL80211_PMKSA_CANDIDATE_INVALID,
+	NL80211_PMKSA_CANDIDATE_INDEX,
+	NL80211_PMKSA_CANDIDATE_BSSID,
+	NL80211_PMKSA_CANDIDATE_PREAUTH,
+
+	/* keep last */
+	NUM_NL80211_PMKSA_CANDIDATE,
+	MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1
+};
+
+/**
+ * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION
+ * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request
+ * @NL80211_TDLS_SETUP: Setup TDLS link
+ * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established
+ * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link
+ * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link
+ */
+enum nl80211_tdls_operation {
+	NL80211_TDLS_DISCOVERY_REQ,
+	NL80211_TDLS_SETUP,
+	NL80211_TDLS_TEARDOWN,
+	NL80211_TDLS_ENABLE_LINK,
+	NL80211_TDLS_DISABLE_LINK,
+};
+
+/*
+ * enum nl80211_ap_sme_features - device-integrated AP features
+ * Reserved for future use, no bits are defined in
+ * NL80211_ATTR_DEVICE_AP_SME yet.
+enum nl80211_ap_sme_features {
+};
+ */
+
+/**
+ * enum nl80211_feature_flags - device/driver features
+ * @NL80211_FEATURE_SK_TX_STATUS: This driver supports reflecting back
+ *	TX status to the socket error queue when requested with the
+ *	socket option.
+ * @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates.
+ */
+enum nl80211_feature_flags {
+	NL80211_FEATURE_SK_TX_STATUS	= 1 << 0,
+	NL80211_FEATURE_HT_IBSS		= 1 << 1,
+};
+
+/**
+ * enum nl80211_probe_resp_offload_support_attr - optional supported
+ *	protocols for probe-response offloading by the driver/FW.
+ *	To be used with the %NL80211_ATTR_PROBE_RESP_OFFLOAD attribute.
+ *	Each enum value represents a bit in the bitmap of supported
+ *	protocols. Typically a subset of probe-requests belonging to a
+ *	supported protocol will be excluded from offload and uploaded
+ *	to the host.
+ *
+ * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS: Support for WPS ver. 1
+ * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2: Support for WPS ver. 2
+ * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P: Support for P2P
+ * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U: Support for 802.11u
+ */
+enum nl80211_probe_resp_offload_support_attr {
+	NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS =	1<<0,
+	NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 =	1<<1,
+	NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P =	1<<2,
+	NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U =	1<<3,
+};
+
 #endif /* __LINUX_NL80211_H */