move lots of kernel related packages to the new system/ folder

SVN-Revision: 33830

3 files changed, 0 insertions, 209 deletions

diff --git a/package/i2c-gpio-custom/src/Kconfig b/package/i2c-gpio-custom/src/Kconfig
deleted file mode 100644
index e2e3a68d92..0000000000
--- a/package/i2c-gpio-custom/src/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-config I2C_GPIO_CUSTOM
-	tristate "Custom GPIO-based I2C driver"
-	depends on GENERIC_GPIO
-	select I2C_GPIO
-	help
-	  This is an I2C driver to register 1 to 4 custom I2C buses using
-	  GPIO lines.
-
-	  This support is also available as a module.  If so, the module
-	  will be called i2c-gpio-custom.
diff --git a/package/i2c-gpio-custom/src/Makefile b/package/i2c-gpio-custom/src/Makefile
deleted file mode 100644
index dcb2e2abe2..0000000000
--- a/package/i2c-gpio-custom/src/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-${CONFIG_I2C_GPIO_CUSTOM}	+= i2c-gpio-custom.o
\ No newline at end of file
diff --git a/package/i2c-gpio-custom/src/i2c-gpio-custom.c b/package/i2c-gpio-custom/src/i2c-gpio-custom.c
deleted file mode 100644
index 76ab5f39cc..0000000000
--- a/package/i2c-gpio-custom/src/i2c-gpio-custom.c
+++ /dev/null
@@ -1,198 +0,0 @@
-/*
- *  Custom GPIO-based I2C driver
- *
- *  Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License version 2 as
- *  published by the Free Software Foundation.
- *
- * ---------------------------------------------------------------------------
- *
- *  The behaviour of this driver can be altered by setting some parameters
- *  from the insmod command line.
- *
- *  The following parameters are adjustable:
- *
- *	bus0	These four arguments can be arrays of
- *	bus1	1-8 unsigned integers as follows:
- *	bus2
- *	bus3	<id>,<sda>,<scl>,<udelay>,<timeout>,<sda_od>,<scl_od>,<scl_oo>
- *
- *  where:
- *
- *  <id>	ID to used as device_id for the corresponding bus (required)
- *  <sda>	GPIO pin ID to used for SDA (required)
- *  <scl>	GPIO pin ID to used for SCL (required)
- *  <udelay>	signal toggle delay.
- *  <timeout>	clock stretching timeout.
- *  <sda_od>	SDA is configured as open drain.
- *  <scl_od>	SCL is configured as open drain.
- *  <scl_oo>	SCL output drivers cannot be turned off.
- *
- *  See include/i2c-gpio.h for more information about the parameters.
- *
- *  If this driver is built into the kernel, you can use the following kernel
- *  command line parameters, with the same values as the corresponding module
- *  parameters listed above:
- *
- *	i2c-gpio-custom.bus0
- *	i2c-gpio-custom.bus1
- *	i2c-gpio-custom.bus2
- *	i2c-gpio-custom.bus3
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include <linux/i2c-gpio.h>
-
-#define DRV_NAME	"i2c-gpio-custom"
-#define DRV_DESC	"Custom GPIO-based I2C driver"
-#define DRV_VERSION	"0.1.1"
-
-#define PFX		DRV_NAME ": "
-
-#define BUS_PARAM_ID		0
-#define BUS_PARAM_SDA		1
-#define BUS_PARAM_SCL		2
-#define BUS_PARAM_UDELAY	3
-#define BUS_PARAM_TIMEOUT	4
-#define BUS_PARAM_SDA_OD	5
-#define BUS_PARAM_SCL_OD	6
-#define BUS_PARAM_SCL_OO	7
-
-#define BUS_PARAM_REQUIRED	3
-#define BUS_PARAM_COUNT		8
-#define BUS_COUNT_MAX		4
-
-static unsigned int bus0[BUS_PARAM_COUNT] __initdata;
-static unsigned int bus1[BUS_PARAM_COUNT] __initdata;
-static unsigned int bus2[BUS_PARAM_COUNT] __initdata;
-static unsigned int bus3[BUS_PARAM_COUNT] __initdata;
-
-static unsigned int bus_nump[BUS_COUNT_MAX] __initdata;
-
-#define BUS_PARM_DESC \
-	" config -> id,sda,scl[,udelay,timeout,sda_od,scl_od,scl_oo]"
-
-module_param_array(bus0, uint, &bus_nump[0], 0);
-MODULE_PARM_DESC(bus0, "bus0" BUS_PARM_DESC);
-module_param_array(bus1, uint, &bus_nump[1], 0);
-MODULE_PARM_DESC(bus1, "bus1" BUS_PARM_DESC);
-module_param_array(bus2, uint, &bus_nump[2], 0);
-MODULE_PARM_DESC(bus2, "bus2" BUS_PARM_DESC);
-module_param_array(bus3, uint, &bus_nump[3], 0);
-MODULE_PARM_DESC(bus3, "bus3" BUS_PARM_DESC);
-
-static struct platform_device *devices[BUS_COUNT_MAX];
-static unsigned int nr_devices;
-
-static void i2c_gpio_custom_cleanup(void)
-{
-	int i;
-
-	for (i = 0; i < nr_devices; i++)
-		if (devices[i])
-			platform_device_put(devices[i]);
-}
-
-static int __init i2c_gpio_custom_add_one(unsigned int id, unsigned int *params)
-{
-	struct platform_device *pdev;
-	struct i2c_gpio_platform_data pdata;
-	int err;
-
-	if (!bus_nump[id])
-		return 0;
-
-	if (bus_nump[id] < BUS_PARAM_REQUIRED) {
-		printk(KERN_ERR PFX "not enough parameters for bus%d\n", id);
-		err = -EINVAL;
-		goto err;
-	}
-
-	pdev = platform_device_alloc("i2c-gpio", params[BUS_PARAM_ID]);
-	if (!pdev) {
-		err = -ENOMEM;
-		goto err;
-	}
-
-	pdata.sda_pin = params[BUS_PARAM_SDA];
-	pdata.scl_pin = params[BUS_PARAM_SCL];
-	pdata.udelay = params[BUS_PARAM_UDELAY];
-	pdata.timeout = params[BUS_PARAM_TIMEOUT];
-	pdata.sda_is_open_drain = params[BUS_PARAM_SDA_OD] != 0;
-	pdata.scl_is_open_drain = params[BUS_PARAM_SCL_OD] != 0;
-	pdata.scl_is_output_only = params[BUS_PARAM_SCL_OO] != 0;
-
-	err = platform_device_add_data(pdev, &pdata, sizeof(pdata));
-	if (err)
-		goto err_put;
-
-	err = platform_device_add(pdev);
-	if (err)
-		goto err_put;
-
-	devices[nr_devices++] = pdev;
-	return 0;
-
-err_put:
-	platform_device_put(pdev);
-err:
-	return err;
-}
-
-static int __init i2c_gpio_custom_probe(void)
-{
-	int err;
-
-	printk(KERN_INFO DRV_DESC " version " DRV_VERSION "\n");
-
-	err = i2c_gpio_custom_add_one(0, bus0);
-	if (err) goto err;
-
-	err = i2c_gpio_custom_add_one(1, bus1);
-	if (err) goto err;
-
-	err = i2c_gpio_custom_add_one(2, bus2);
-	if (err) goto err;
-
-	err = i2c_gpio_custom_add_one(3, bus3);
-	if (err) goto err;
-
-	if (!nr_devices) {
-		printk(KERN_ERR PFX "no bus parameter(s) specified\n");
-		err = -ENODEV;
-		goto err;
-	}
-
-	return 0;
-
-err:
-	i2c_gpio_custom_cleanup();
-	return err;
-}
-
-#ifdef MODULE
-static int __init i2c_gpio_custom_init(void)
-{
-	return i2c_gpio_custom_probe();
-}
-module_init(i2c_gpio_custom_init);
-
-static void __exit i2c_gpio_custom_exit(void)
-{
-	i2c_gpio_custom_cleanup();
-}
-module_exit(i2c_gpio_custom_exit);
-#else
-subsys_initcall(i2c_gpio_custom_probe);
-#endif /* MODULE*/
-
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Gabor Juhos <juhosg@openwrt.org >");
-MODULE_DESCRIPTION(DRV_DESC);
-MODULE_VERSION(DRV_VERSION);