aboutsummaryrefslogtreecommitdiffstats
path: root/package/firmware/ipq-wifi
diff options
context:
space:
mode:
authorFelix Matouschek <felix@matouschek.org>2021-07-15 21:48:11 +0200
committerHauke Mehrtens <hauke@hauke-m.de>2021-11-28 18:39:01 +0100
commit1cc3b95efcc616fba91a7f34e9781743229cc640 (patch)
treef412fc5d20cbc34fdda146b87a17032ce3bd4352 /package/firmware/ipq-wifi
parent67f52012760ce553ba6393aaba77359a458deeda (diff)
downloadupstream-1cc3b95efcc616fba91a7f34e9781743229cc640.tar.gz
upstream-1cc3b95efcc616fba91a7f34e9781743229cc640.tar.bz2
upstream-1cc3b95efcc616fba91a7f34e9781743229cc640.zip
ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org>
Diffstat (limited to 'package/firmware/ipq-wifi')
-rw-r--r--package/firmware/ipq-wifi/Makefile4
-rw-r--r--package/firmware/ipq-wifi/board-teltonika_rutx.qca4019bin0 -> 24276 bytes
2 files changed, 3 insertions, 1 deletions
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 6835363cb6..ebaac48c24 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -51,7 +51,8 @@ ALLWIFIBOARDS:= \
p2w_r619ac \
plasmacloud_pa1200 \
plasmacloud_pa2200 \
- qxwlan_e2600ac
+ qxwlan_e2600ac \
+ teltonika_rutx
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
@@ -139,5 +140,6 @@ $(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa2200,Plasma Cloud PA2200))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
+$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-teltonika_rutx.qca4019 b/package/firmware/ipq-wifi/board-teltonika_rutx.qca4019
new file mode 100644
index 0000000000..440c63af41
--- /dev/null
+++ b/package/firmware/ipq-wifi/board-teltonika_rutx.qca4019
Binary files differ