(6/6) bcm57xx: package

This is the bcm57xx package.  I have tested default vlan functions,
but I dont have the equipment to test more advanced setups.  The default
vlan setup seems to be working fine.  I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.

I'm not sure which method is best for autoload.  For the wrt350n, I
need the activate_gpio parameter.  But its probably not a good idea
to add that to the autoload file.  On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on?  I tried using 'request_module' from
there, but had no success.  For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.

Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 52 insertions, 0 deletions

diff --git a/package/broadcom-57xx/src/proto/vlan.h b/package/broadcom-57xx/src/proto/vlan.h
new file mode 100644
index 0000000000..79cd5891e1
--- /dev/null
+++ b/package/broadcom-57xx/src/proto/vlan.h
@@ -0,0 +1,52 @@
+/*
+ * 802.1Q VLAN protocol definitions
+ *
+ * Copyright 2007, Broadcom Corporation
+ * All Rights Reserved.
+ * 
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ * $Id: vlan.h,v 1.1.1.4 2007/05/31 08:00:41 michael Exp $
+ */
+
+#ifndef _vlan_h_
+#define _vlan_h_
+
+/* enable structure packing */
+#if defined(__GNUC__)
+#define	PACKED	__attribute__((packed))
+#else
+#pragma pack(1)
+#define	PACKED
+#endif
+
+#define VLAN_VID_MASK		0xfff	/* low 12 bits are vlan id */
+#define	VLAN_CFI_SHIFT		12	/* canonical format indicator bit */
+#define VLAN_PRI_SHIFT		13	/* user priority */
+
+#define VLAN_PRI_MASK		7	/* 3 bits of priority */
+
+#define	VLAN_TAG_LEN		4
+#define	VLAN_TAG_OFFSET		(2 * ETHER_ADDR_LEN)	/* offset in Ethernet II packet only */
+
+#define VLAN_TPID		0x8100	/* VLAN ethertype/Tag Protocol ID */
+
+struct ethervlan_header {
+	uint8	ether_dhost[ETHER_ADDR_LEN];
+	uint8	ether_shost[ETHER_ADDR_LEN];
+	uint16	vlan_type;		/* 0x8100 */
+	uint16	vlan_tag;		/* priority, cfi and vid */
+	uint16	ether_type;
+};
+
+#define	ETHERVLAN_HDR_LEN	(ETHER_HDR_LEN + VLAN_TAG_LEN)
+
+#undef PACKED
+#if !defined(__GNUC__)
+#pragma pack()
+#endif
+
+#endif /* _vlan_h_ */