(6/6) bcm57xx: package

This is the bcm57xx package.  I have tested default vlan functions,
but I dont have the equipment to test more advanced setups.  The default
vlan setup seems to be working fine.  I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.

I'm not sure which method is best for autoload.  For the wrt350n, I
need the activate_gpio parameter.  But its probably not a good idea
to add that to the autoload file.  On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on?  I tried using 'request_module' from
there, but had no success.  For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.

Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>

SVN-Revision: 11471

1 files changed, 101 insertions, 0 deletions

diff --git a/package/broadcom-57xx/src/proto/bcmeth.h b/package/broadcom-57xx/src/proto/bcmeth.h
new file mode 100644
index 0000000000..fffce6e7b5
--- /dev/null
+++ b/package/broadcom-57xx/src/proto/bcmeth.h
@@ -0,0 +1,101 @@
+/*
+ * Broadcom Ethernettype  protocol definitions
+ *
+ * Copyright 2007, Broadcom Corporation
+ * All Rights Reserved.
+ * 
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ * $Id: bcmeth.h,v 1.1.1.5 2007/05/31 08:00:41 michael Exp $
+ */
+
+/*
+ * Broadcom Ethernet protocol defines
+ */
+
+#ifndef _BCMETH_H_
+#define _BCMETH_H_
+
+/* enable structure packing */
+#if defined(__GNUC__)
+#define	PACKED	__attribute__((packed))
+#else
+#pragma pack(1)
+#define	PACKED
+#endif
+
+/* ETHER_TYPE_BRCM is defined in ethernet.h */
+
+/*
+ * Following the 2byte BRCM ether_type is a 16bit BRCM subtype field
+ * in one of two formats: (only subtypes 32768-65535 are in use now)
+ *
+ * subtypes 0-32767:
+ *     8 bit subtype (0-127)
+ *     8 bit length in bytes (0-255)
+ *
+ * subtypes 32768-65535:
+ *     16 bit big-endian subtype
+ *     16 bit big-endian length in bytes (0-65535)
+ *
+ * length is the number of additional bytes beyond the 4 or 6 byte header
+ *
+ * Reserved values:
+ * 0 reserved
+ * 5-15 reserved for iLine protocol assignments
+ * 17-126 reserved, assignable
+ * 127 reserved
+ * 32768 reserved
+ * 32769-65534 reserved, assignable
+ * 65535 reserved
+ */
+
+/* 
+ * While adding the subtypes and their specific processing code make sure
+ * bcmeth_bcm_hdr_t is the first data structure in the user specific data structure definition
+ */
+
+#define	BCMILCP_SUBTYPE_RATE		1
+#define	BCMILCP_SUBTYPE_LINK		2
+#define	BCMILCP_SUBTYPE_CSA		3
+#define	BCMILCP_SUBTYPE_LARQ		4
+#define BCMILCP_SUBTYPE_VENDOR		5
+#define	BCMILCP_SUBTYPE_FLH		17
+
+#define BCMILCP_SUBTYPE_VENDOR_LONG	32769
+#define BCMILCP_SUBTYPE_CERT		32770
+#define BCMILCP_SUBTYPE_SES		32771
+
+
+#define BCMILCP_BCM_SUBTYPE_RESERVED	0
+#define BCMILCP_BCM_SUBTYPE_EVENT		1
+#define BCMILCP_BCM_SUBTYPE_SES			2
+/*
+ * The EAPOL type is not used anymore. Instead EAPOL messages are now embedded
+ * within BCMILCP_BCM_SUBTYPE_EVENT type messages
+ */
+/* #define BCMILCP_BCM_SUBTYPE_EAPOL		3 */
+
+#define BCMILCP_BCM_SUBTYPEHDR_MINLENGTH	8
+#define BCMILCP_BCM_SUBTYPEHDR_VERSION		0
+
+/* These fields are stored in network order */
+typedef  struct bcmeth_hdr
+{
+	uint16	subtype;	/* Vendor specific..32769 */
+	uint16	length;
+	uint8	version;	/* Version is 0 */
+	uint8	oui[3];		/* Broadcom OUI */
+	/* user specific Data */
+	uint16	usr_subtype;
+} PACKED bcmeth_hdr_t;
+
+#undef PACKED
+#if !defined(__GNUC__)
+#pragma pack()
+#endif
+
+#endif	/*  _BCMETH_H_ */