aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot/uboot-envtools
diff options
context:
space:
mode:
authorMichael Pratt <mcpratt@pm.me>2021-06-12 15:08:18 -0400
committerHauke Mehrtens <hauke@hauke-m.de>2022-09-11 21:54:00 +0200
commit9f6e24785439d7838fc7a338505cbfac9687a90d (patch)
treeaccf7d388db0c3758b819356bbfbe8d9305d89f8 /package/boot/uboot-envtools
parent146aaeafb7e364ca667f6ddf5c1857148e8bffb2 (diff)
downloadupstream-9f6e24785439d7838fc7a338505cbfac9687a90d.tar.gz
upstream-9f6e24785439d7838fc7a338505cbfac9687a90d.tar.bz2
upstream-9f6e24785439d7838fc7a338505cbfac9687a90d.zip
ath79: add support for Senao WatchGuard AP200
FCC ID: U2M-CAP4200AG WatchGuard AP200 is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP600 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - AR9382 WLAN PCI card 168c:0030, 5 GHz, 2x2, 26dBm - AR8035-A EPHY RGMII GbE with PoE+ IN - 25 MHz clock - 16 MB FLASH mx25l12805d - 2x 64 MB RAM - UART console J11, populated - GPIO watchdog GPIO 16, 20 sec toggle - 4 antennas 5 dBi, internal omni-directional plates - 5 LEDs power, eth0 link/data, 2G, 5G - 1 button reset **MAC addresses:** Label has no MAC Only one Vendor MAC address in flash at art 0x0 eth0 ---- *:be art 0x0 -2 phy1 ---- *:bf art 0x0 -1 phy0 ---- *:be art 0x0 -2 **Installation:** Method 1: OEM webpage use OEM webpage for firmware upgrade to upload factory.bin Method 2: root shell It may be necessary to use a Watchguard router to flash the image to the AP and / or to downgrade the software on the AP to access SSH For some Watchguard devices, serial console over UART is disabled. NOTE: DHCP is not enabled by default after flashing **TFTP recovery:** reset button has no function at boot time only possible with modified uboot environment, (see commit message for Watchguard AP300) **Return to OEM:** user should make backup of MTD partitions and write the backups back to mtd devices in order to revert to OEM reliably It may be possible to use sysupgrade with an OEM image as well... (not tested) **OEM upgrade info:** The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. **Note on eth0 PLL-data:** The default Ethernet Configuration register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For AR934x series, the PLL registers for eth0 can be see in the DTSI as 0x2c. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 **Note on WatchGuard Magic string:** The OEM upgrade script is a modified version of the generic Senao sysupgrade script which is used on EnGenius devices. On WatchGuard boards produced by Senao, images are verified using a md5sum checksum of the upgrade image concatenated with a magic string. this checksum is then appended to the end of the final image. This variable does not apply to all the senao devices so set to null string as default Tested-by: Steve Wheeler <stephenw10@gmail.com> Tested-by: John Delaney <johnd@ankco.net> Signed-off-by: Michael Pratt <mcpratt@pm.me>
Diffstat (limited to 'package/boot/uboot-envtools')
-rw-r--r--package/boot/uboot-envtools/files/ath791
1 files changed, 1 insertions, 0 deletions
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 64b2b34d8a..588c7dee02 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -67,6 +67,7 @@ openmesh,om5p-ac-v1|\
openmesh,om5p-ac-v2|\
samsung,wam250|\
ubnt,nanostation-m|\
+watchguard,ap200|\
watchguard,ap300|\
yuncore,a770|\
yuncore,a782|\