diff options
| author | Sven Eckelmann <sven.eckelmann@openmesh.com> | 2017-08-09 13:52:07 +0200 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-04-23 22:07:22 +0200 |
| commit | 0b204902075157dbb002ea04f41a5b1a4fbe848c (patch) | |
| tree | aab0a3eabea2d909bb41909c6a6d0b5583967495 /package/boot/uboot-envtools/files/ipq40xx | |
| parent | c6aac196b80039ae1716b9af635c06992e62171f (diff) | |
| download | upstream-0b204902075157dbb002ea04f41a5b1a4fbe848c.tar.gz upstream-0b204902075157dbb002ea04f41a5b1a4fbe848c.tar.bz2 upstream-0b204902075157dbb002ea04f41a5b1a4fbe848c.zip | |
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Diffstat (limited to 'package/boot/uboot-envtools/files/ipq40xx')
| -rw-r--r-- | package/boot/uboot-envtools/files/ipq40xx | 3 |
1 files changed, 2 insertions, 1 deletions
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index 4eae506fb1..d475e56629 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -31,7 +31,8 @@ ubootenv_mtdinfo () { } case "$board" in -openmesh,a42) +openmesh,a42 |\ +openmesh,a62) ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000" ;; esac |